Search results

This paper aims to design the nano-titanium dioxide (TiO₂) coating system which has superhydrophilic property, self-cleaning mechanism and antifog property as well as strong adhesion on glass substrate.

Two hydrophilic materials have been used such as TiO₂ nanoparticles as fillers and hydrophilic copolymer, Pluronic F-127 by using simple sol–gel approach. The prepared solution was applied onto glass through dip- and spray-coating techniques and then left for drying at ambient temperature.

The nano-TiO₂ superhydrophilic coating has achieved the water contact angle of 4.9° ± 0.5°. The superhydrophilic coating showed great self-cleaning effect against concentrated syrup and methylene blue where thin layer of water washes the dirt contaminants away. The nano-TiO₂ coating exhibits great antifog performance that maintains high transparency of around 89% when the coated glass is placed above hot-fog vapor for 10 min. The fog droplets were condensed into water film which allowed the transmission of light through the glass. The strong adhesion of coated glass shows no total failure at scratch profile when impacted with scratch load of 500, 800 and 1,200 mN.

Findings will be useful in the development of self-cleaning superhydrophilic coating that is applicable on building glass and photovoltaic panel.

The developed nano-TiO₂ coating is developed by the combination of hydrophilic organic copolymer–inorganic TiO₂ network to achieve great superhydrophilic property, optimum self-cleaning ability and supreme antifog performance.

The findings will be useful for residents in building glass window where the application will reduce dust accumulation and keep the glass clean for longer period.

The synthesis of nano-TiO₂ superhydrophilic coating which can be sprayed on large glass panel and cured at ambient temperature.

The paper aims to design the optimum formulation of the nano-titanium dioxide (TiO2) hydrophilic coating system using the synthetic polypropylene glycol (PPG), which can create the reflection and absorption property.

TiO2 nanoparticles are used as fillers, and PPG has been blended at the proper ratio of 1PPG: 0.2TiO2. The prepared resin has been applied onto the glass substrate at different numbers of glass immersions during the dip-coating fabrication process. One-time glass immersion is labeled as T1 coating, two-time glass immersion is labeled as T2 coating and three-time glass immersion is labeled as T3 coating. All the prepared coating systems were left dry at ambient temperature.

T3 coating showed the lowest reading of WCA value at 40.50°, due to higher surface energy at 61.73 mN/m. The T3 coating also shows the greatest absorbance property among the prepared coating systems among the prepared coating. In terms of reflectance property, the T2 coating system has great reflectance in UV region and near-infrared region, which is 16.47% and 2.77 and 2.73%, respectively. The T2 coating also has great optical transmission about 75.00% at the visible region.

The development of thermal insulation coating by studying the relationship between convection heat and reflectance at different wavelengths of incident light.

The developed coating shows high potential for glass window application.

The application of the hydrophilic coating on light absorption, reflectance and transmission at different wavelengths.

The purpose of this study is to perform comprehensive investigation to assess the mechanical properties of nano-modified ternary cement concrete blend. Nano silica (NS) (1%, 2% and 3%) and waste marble dust powder (MD) (5%, 10% and 15%) was incorporated as a fractional substitution of cement in the concrete matrix.

In this experimental study, 10 cementitious blends were prepared and tested for compressive strength, flexural strength, splitting tensile strength and static modulus of elasticity. The microstructural characteristics of these blends were also explored using a scanning electron microscope along with energy dispersive spectroscopy and X-ray reflection.

The results indicate an enhancement in mechanical properties and refinement in pore structure due to improved pozzolanic activities of NS and the filling effect of MD.

To the best of the authors’ knowledge, no study has reported the mechanical and microstructural behavior of concrete containing marble and NS.

This study aims to evaluate the thermal performance of sodium alginate (SA) aerogel attached to nano SiO₂ and its radiative cooling effect on firefighting clothing without environmental pollution.

SA/SiO₂ aerogel with refractory heat insulation and enhanced radiative cooling performance was fabricated by freeze-drying method, which can be used in firefighting clothing. The microstructure, chemical composition, thermal stability, and thermal emissivity were analyzed using Fourier transform infrared spectroscopy, scanning electron microscopy, thermogravimetric analyzer and infrared emissivity measurement instrument. The radiative cooling effect of aerogel was studied using thermal infrared imager and thermocouple.

When the addition of SiO₂ is 25% of SA, the prepared aerogel has excellent heat insulation and a high radiative cooling effect. Under a clear sky, the temperature of SA/SiO₂ aerogel is 9.4°C lower than that of pure SA aerogel and 22.1°C lower than that of the simulated environment. In addition, aerogel has more exceptional heat insulation effect than other common fabrics in the heat insulation performance test.

SA/SiO₂ aerogel has passive radiative cooling function, which can efficaciously economize global energy, and it is paramount to environment-friendly cooling.

This method could pave the way for high-performance cooling materials designed for firefighting clothing to keep maintain the wearing comfort of firefighters.

SA/SiO₂ aerogel used in firefighting clothing can release heat to the low-temperature outer space in the form of thermal radiation to achieve its own cooling purpose, without additional energy supply.

The purpose of this study is to investigate the influence of varying concentrations of nano-SiO₂ particle doping on the structure and properties of the micro-arc oxidation (MAO) coating of 7075 aluminum alloy. This research aims to provide novel insights and methodologies for the surface treatment and protection of 7075 aluminum alloy.

The surface morphology of the MAO coating was characterized using scanning electron microscope. Energy spectrometer was used to characterize the elemental content and distribution on the surface and cross section of the MAO coating. The phase composition of the MAO coating was characterized using X-ray diffractometer. The corrosion resistance of the MAO coating was characterized using an electrochemical workstation.

The results showed that when the addition of nano-SiO₂ particles is 3 g/L, the corrosion resistance is optimal.

This study investigated the influence of different concentrations of nano-SiO₂ particles on the structure and properties of the MAO coating of 7075 aluminum alloy.

The purpose of this paper is to explore the effect of ZnO on the structure and properties of micro-arc oxidation (MAO) coating on rare earth magnesium alloy under large concentration gradient.

The macroscopic and microscopic morphology, thickness, surface roughness, chemical composition and structure of the coating were characterized by different characterization methods. The corrosion resistance of the film was studied by electrochemical and scanning Kelvin probe force microscopy. The results show that the addition of ZnO can significantly improve the compactness and corrosion resistance of the MAO coating, but the high concentration of ZnO will cause microcracks, which will reduce the corrosion resistance to a certain extent.

When the concentration of zinc oxide is 8 g/L, the compactness and corrosion resistance of the coating are the best, and the thickness of the coating is positively correlated with the concentration of ZnO.

Too high concentration of ZnO reduces the performance of MAO coating.

The MAO coating prepared by adding ZnO has good corrosion resistance. Combined with organic coatings, it can be applied in corrosive marine environments, such as ship parts and hulls. To a certain extent, it can reduce the economic loss caused by corrosion.

The effect of ZnO on the corrosion resistance of MAO coating in electrolyte solution was studied systematically, and the conclusion was new to the common knowledge.

This study aims to characterize the mechanical properties of sintered nano-silver under various sintering processes by nano-indentation tests.

Through microstructure observations and characterization, the influences of sintering process on the microstructure evolutions of sintered nano-silver were presented. And, the indentation load, indentation displacement curves of sintered silver under various sintering processes were measured by using nano-indentation test. Based on the nano-indentation test, a reverse analysis of the finite element calculation was used to determine the yielding stress and hardening exponent.

The porosity decreases with the increase of the sintering temperature, while the average particle size of sintered nano-silver increases with the increase of sintering temperature and sintering time. In addition, the porosity reduced from 34.88%, 30.52%, to 25.04% if the ramp rate was decreased from 25°C/min, 15°C/min, to 5°C/min, respectively. The particle size appears more frequently within 1 µm and 2 µm under the lower ramp rate. With reverse analysis, the strain hardening exponent gradually heightened with the increase of temperature, while the yielding stress value decreased significantly with the increase of temperature. When the sintering time increased, the strain hardening exponent increased slightly.

The mechanical properties of sintered nano-silver under different sintering processes are clearly understood.

This paper could provide a novel perspective on understanding the sintering process effects on the mechanical properties of sintered nano-silver.

This paper aims to investigate the thermal stability and hydrophobicity of difference alkyl chain of silanes with silicon (Si) micro- and nanoparticles.

Sol-gel methods have been used to design superhydrophobic glass substrates through surface modification by using low-surface-energy Isooctyl trimethoxysilane (ITMS) and Ethyl trimethoxysilane (ETMS) solution. Hierarchical double-rough scale solid surface was built by Si micro- and nanoparticles to enhance the surface roughness. The prepared sol was applied onto glass substrate using dip-coating method and was dried at control temperature of 400°C inside the tube furnace.

The glass substrate achieved the water contact angle as high as 154 ± 2° and 150.4 ± 2° for Si/ITMS and Si/ETMS films, respectively. The Si/ITMS and Si/ETMS also were equipped with low sliding angle as low as 3° and 5°, respectively. The Si micro- and nanoparticles in the coating system have created nanopillars between them, which will suspend the water droplets. Both superhydrophobic coatings have showed good stability against high temperature up to 200°C as there are no changes in WCA shown by both coatings. Si/ITMS film sustains its superhydrophobicity after impacting with further temperature up to 400°C and turns hydrophobic state at 450°C.

Findings will be useful to develop superhydrophobic coatings with high thermal stability.

Sol method provides a suitable medium for the combination of organic-inorganic network to achieve high hydrophobicity with optimum surface roughness.

Application of different alkyl chain groups of silane resin blending with micro- and nanoparticles of Si pigments develops superhydrophobic coatings with high thermal stability.

This study aims to optimize the preparation conditions and modify the nanofiltration (NF) membranes to prepare high-performance polysulfone/sulfonated polysulfone composite nanofiltration (PSF/SPSF-NF) membranes through interfacial polymerization.

Investigating the impacts of anhydrous piperazine (PIP) concentration, trimesoyl chloride (TMC) concentration and basement membrane type on NF membrane performance, the optimal membrane was prepared. In addition, nano-SiO₂ was added to the active separation layer to modify the NF membranes.

The comprehensive performance of PSF/SPSF-NF membranes was optimized when the concentration of PIP was 0.75 Wt.% and the concentration of TMC was 0.15 Wt.%, at which time the water flux was 66.1 L·m⁻²·h⁻¹ and the retention rate of Na₂SO₄ was 98.1%. The comprehensive performance of polysulfone/sulfonated polysulfone-SiO₂ nanofiltration (PSF/SPSF-SiO₂-NF) membranes was optimized when the blending ratio of nano-SiO₂ to PIP was 2:3, with a pure water flux of 81.9 L·m⁻²·h⁻¹ and a Na₂SO₄ retention rate of 95.9%. Compared to polysulfone nanofiltration (PSF-NF) membranes and PSF/SPSF-NF membranes, NF membranes with nano-SiO₂ increased the flux recovery rate by 22.9% and 8.7%.

PSF/SPSF-SiO2-NF membrane exhibits excellent antifouling properties.

There is currently no literature available on the preparation of NF membranes using polysulfone/sulfonated polysulfone (PSF/SPFS) as a substrate. This provides a method for modifying NF membranes, starting with the modification of the basement membrane and then modifying the active separation layer.

This study aimed to review various existing methods for improving the quality of recycled concrete aggregates (RCAs) as a possible substitution for natural aggregates (NAs) in concrete. It is vital as the old paste attached to the RCA weakens its structure. It is due to the porous structure of the RCA with cracks, weakening the interfacial transition zone (ITZ) between the RCA and binding material, negatively impacting the concrete's properties. To this end, various methods for reinforcement of the RCA, cleaning the RCA's old paste and enhancing the quality of the RCA-based concrete without RCA modification are studied in terms of environmental effects, cost and technical matters. Furthermore, this research sought to identify gaps in knowledge and future research directions.

The review of the relevant journal papers revealed that various methods exist for improving the properties of RCAs and RCA-based concrete. A decision matrix was developed and implemented for ranking these techniques based on environmental, economic and technical criteria.

The identified methods for reinforcement of the RCA include accelerated carbonation, bio deposition, soaking in polymer emulsions, soaking in waterproofing admixture, soaking in sodium silicate, soaking in nanoparticles and coating with geopolymer slurry. Moreover, cleaning the RCA's old paste is possible using acid, water, heating, thermal and mechanical treatment, thermo-mechanical and electro-dynamic treatment. Added to these treatment techniques, using RCA in saturated surface dry (SSD) mixing approaches and adding fibres or pozzolana enhance the quality of the RCA-based concrete without RCA modification. The study ranked these techniques based on environmental, economic and technical criteria. Ultimately, adding fibres, pozzolana and coating RCA with geopolymer slurry were introduced as the best techniques based on the nominated criteria.

The study supported the need for better knowledge regarding the existing treatment techniques for RCA improvement. The outcomes of this research offer an understanding of each RCA enrichment technique's importance in environmental, economic and technical criteria.

The practicality of the RCA treatment techniques is based on economic, environmental and technical specifications for rating the existing treatment techniques.