Search results

This paper aims to investigate the scuffing load‐carrying capacity of three gear oils: a standard mineral lubricant containing extreme pressure and anti‐wear additives (M0) and two biodegradable saturated esters containing low toxicity additives (E1 and E2).

Four‐ball wear tests were performed, according to standard ASTM D4172. Results from the wear scar diameter and from ferrographic analysis of the test oil samples are presented and related to the lubricant properties. The physical, chemical and biodegradability properties of the lubricants are presented and compared.FZG gear scuffing tests were performed, according to standard DIN 51535, in order to evaluate the scuffing load‐carrying capacity of the two oils. Two reference tests were performed, A20/16.6/90 and A10/16.6/90.

Test results include scuffing load stage, maximum oil bath temperature, pinion weight loss and surface roughness measurement of the teeth flanks.

The paper provides information on the scuffing load‐carrying capacity of three gear oils.

The purpose of this paper is to investigate applicability of hexagonal boron nitride (h-BN) powder as a solid lubricant additive in coconut oil and to determine the tribological behavior of PEEK rubbed with DIN2080 tool steel, under prepared green lubricating condition.

In this study, tiribological performance of PEEK against the DIN2080 tool steel is investigated with green lubricant. Coconut oil was used as green lubricant and 4 per cent wt. h-BN powder was added as lubricant additive into the coconut oil. Reciprocal pin-plate tribological test were applied under dry, coconut oil and coconut oil+h-BN lubrication condition. Friction coefficients were recorded and wear behavior of the samples investigated by mass loss measurement and topographical inspection of wear track by optical profilometer.

Using coconut oil as lubricant provided 80 per cent reduction of friction coefficient and 33.4 per cent reduction of wear rate. Addition of h-BN into the coconut oil provide 84 per cent reduction of friction coefficient and 56 per cent reduction of wear rate. The results showed that vegetable oil is promising lubricant for sustainable manufacturing. h-BN serves to increase lubricant performance and decrease wear of the surfaces.

Petrochemical lubricants are one of the major sources of environmental pollution and health hazards. Development and use of environmental and health friendly lubricants support sustainability and reduce wear, friction and energy consumption. With this consciousness, recent studies have focused on green tribology and green lubricants such as vegetable oils, ionic liquid bio-lubricants and bio-based polymers.

In literature study coconut oil was proposed as green lubricant while h-BN powder was proposed as solid lubricant. However, applicability of h-BN powder in coconut oil has not been explored yet. Moreover, wear and friction property of PEEK material with DIN 2080 tool steel pair surface has not been studied yet with green lubricants.

The purpose of this paper is to assess lubricating performances of selected locally produced vegetable oil‐based lubricants with a view to utilizing them as a possible alternative to petroleum‐based lubricants in metal‐forming processes.

The ring compression testing and twin disks upsetting testing methods were employed.

The results obtained from these two tests showed that the red palm oil performed better than others at room temperature, followed by sheabutter oil, while palm kernel oil performed the least. High‐temperatures compression ring tests gave sheabutter oil lower values of friction coefficients than red palm oil.

Further work should be done on numerous vegetable oil‐based lubricants. Also those that show promising performance could be further investigated with locally available additives.

These are numerous since increase in environmental interest has resulted in a renewed interest in vegetable oil‐based lubricants.

The research work has broken new ground in finding applications for environmentally friendly lubricants in various areas of metal‐forming processes.

The purpose of this paper is to present the results of research into using an additive to SAE 15W/40 engine oil during operation and its influence on lubricating properties (normalised tests) on weld point Pz, non-seizure load Pn, load wear index Ih and on seizure load Pt. The friction pair consisted of a group of four balls and the tested lubricant. Moreover, the author tested the influence of an additive to engine oil (non-normalised tests) on tribological properties, including friction force, wear and the temperature of friction area for the C45 steel/210Cr12 steel friction joint. She also determined the influence of an additive to engine oil on the formation of the operating surface layer. The research results helped to build the model of the boundary layer that was formed as a result of adding an additive to engine oil.

The lubricant properties of engine oil and engine oil to which an additive was added during operation were determined according to PN-76/C-04147. The following are the indexes of lubricant properties: weld point Pz, load wear index Ih, non-seizure load Pn, seizure load and average scar diameter. The Pz, Pn and Ih indexes were determined at abruptly increasing load to the moment of welding of the friction pair. The Pt index was determined at the increasing load of the friction pair from 0 to 800 daN at the speed of 408.8 N/s. The tests of tribological properties (friction force, wear and the temperature of friction area) were conducted for the C45/210 Cr12 friction pair in the presence of a lubricant and a lubricant with an additive.

The modification of SAE 15W/40 engine oil with the additive added during operation resulted in improved indexes of lubricant properties Pz, Pn, Ih and Pt and average scar diameter. The boundary layer for the modified oil breaks after a longer time and at lesser friction force. The modification of the engine oil reduced the wear of the friction pair. After the friction process, element composition in the surface layer of the wear trace and its distribution were determined in relation to applied lubricants. A significant amount of sulphur, phosphorus and oxygen, as well as an insignificant amount of copper, was observed in the wear trace after the friction process in the presence of the lubricant medium. The distribution of elements in the wear trace when the engine oil with the additive was used is steady in the wear trace and outside it. Some sulphur, phosphorus and chlorine were found in the wear trace.

The results of tests on tribological properties (non-normalised tests) confirmed the positive affect of the additive to engine oil on lubricant properties (normalised tests). The modification of the engine oil caused reduced friction force and the reduced wear of the friction pair. The reduction of friction force and wear was the result of the formation of the surface of a greater amplitude density of unevenness tops in the friction process. Moreover, the operating surface layer, created in the friction process when the additive was added to the engine oil, had greater load participation at 50 per cent C. This operational surface layer improved tribological properties, i.e. it reduced value of friction force and wear. The test results were used to build a model of the boundary layer created as a result of the additive added to engine oil.

The purpose of the paper is to assess the influence of the volume fraction solid lubricants like talc lead and graphite in oil separately and in combination towards controlling the sliding wear behaviour of a grey cast iron and understand the factors controlling the response of the material in a given set of experimental conditions.

The composition of the lubricating medium (oil) has been changed by dispersing 5 per cent graphite, talc and lead particles separately and in combination. Sliding wear tests were conducted on grey cast iron samples over a range of applied pressures. Parameters determined were wear rate and frictional heating. The wear behaviour of the samples was further substantiated through the features of wear surfaces, subsurface regions and debris particles. Material removal mechanisms and factors responsible for a specific response of the samples have also been analysed.

The wear rate increased with increasing applied pressure. Addition of graphite and lead to the oil separately or in combination brought about a reduction in the wear rate of the samples; talc and talc + lead produced a reverse trend. Temperature near the specimen surface increased with test duration and applied pressure. The test environment influenced the frictional heating in a manner similar to that of the wear rate. Adhesion and abrasion were observed to be the operating material removal mechanisms. Smearing of the solid lubricating phase and delamination resulting from cracking tendency also controlled the wear response.

Oil is a very popular lubricant used in engineering applications involving friction and wear. Solid lubricants are used along with the oil. The nature, characteristics and content of the solid lubricants very much control the performance. Limited information is available pertaining to assessing the influence of the type and fraction of solid lubricants in the oil towards controlling the wear behaviour of cast irons (popularly known tribomaterials). The present study enables to understand the effectiveness of talc, lead and graphite in oil towards governing the wear characteristics of cast iron and analyse wear mechanisms and controlling parameters.

Graphite and talc are available in nature in abundance. Graphite is a popularly known solid lubricant, while talc is less explored. Lead is also well-known as a solid lubricant but poses health hazard in practice due to its toxic nature. The present study explores the lubricating capability of talc when mixed with oil separately or in combination with lead and graphite towards controlling the wear response of a grey cast iron. It enables to understand the factors responsible for the specific response of talc.

Assessment of the lubricating potential of talc as a possible substitute to lead is important in view of the toxic nature of the latter. If successful, the exercise could enable to replace lead with talc.

The present manuscript is an original piece of the author's research work.

A number of oleochemicals have found application in the formulation of metal processing lubricants. Calcium palmitate can act as a gelling inhibitor for lubricants for non‐chip metal forming, and diglyceryl oleate and sodium oleyl sulphate have been employed in chipless forming and machining lubricants. Glyceryl monooleate has been used together with paraffin wax and xylene for forming aluminium sheets, and isopropyl oleate has been blended into lubricants for cold forming of metal. Lubrication in cold forming of steel and aluminium alloys has been promoted by the use of sodium stearate and phosphating processes. Stearic acid has also been utlized in metal forming. Butyl butanamine stearamide is applicable in lubricants for non‐ferrous metal working, and coatings that can prevent galling when titanium is cold worked can be formed on the metal by the use of 0.5 grams of hydrofluoric acid, with 10 grams stearic acid in 100 ml. of a solvent, the process being accelerated by the inclusion of phosphoric acid at 0.85 grams. Calcium stearate has also been used in solvent‐based metalworking Iubricants, in acrylic electrophoretic lubricant coatings on metal, and in bentonite‐containing metalworking oils. Mixtures of cetyl alcohol and tricresyl phosphate have been cast into slabs and used on metalworking tools.

The optimal performance of the machinery is based on lubricants that require frequent monitoring and the analysis of characteristics such as chemical content, contamination and viscosity. The application of nanoparticles dispersed lubricant in tribology has received remarkable attention in recent years. This paper aims to investigate the tribological properties of SN500 grade lubricating oil containing garnet nanoparticles.

In this study, 45-nm-sized garnet particles are ultrasonically dispersed in SN500 grade base lubricant oil. The effects of viscosity and additive concentration on tribological properties are investigated using a four-ball tester.

Rolling, reinforcing and film-forming behaviour of dispersed nano-sized garnet additives in the rubbing zone were investigated using scanning electron microscopy equipped with energy dispersive spectroscopy. The results indicate that the garnet additives can improve the wear resistance and resistance to relative motion and decrease the friction coefficient of rubbing steel interface by surface polishing and formation of tribo-film containing Si, C and Mn.

Because of the complex two-phase solid–liquid mixture, there are still limited physical understandings of the friction and wear reduction mechanisms. Therefore, the present research was undertaken to interpret the possible phenomena.

The purpose of this paper is to understand the sliding wear response of a cast iron as influenced by applied load and changing concentration of solid lubricant (graphite) particles in oil lubricant, and operating material removal mechanisms in different sets of experimental conditions.

The sliding wear response of a grey cast iron has been examined as a function of test environment and load. Properties evaluated were wear rate, friction coefficient and frictional heating. The wear behaviour of the samples has been substantiated through the characteristics of their wear surfaces, subsurface regions and debris particles.

The wear rate and frictional heating increased with load while friction coefficient was affected in an opposite manner. The presence of oil lubricant led to a substantial improvement in wear response (in terms of decreasing wear rate, friction coefficient and frictional heating) while the presence of graphite particles in the oil lubricant proved to be still better. A critical content of graphite in the oil lubricant becomes most effective towards improving the wear response of the samples. Formation of dark patches on the wear surface, substantial subsurface deformation and fine debris led to improved wear response.

The study enables one to understand the wear behaviour of a cast iron as influenced by the changing concentration of solid lubricant (graphite) particles in the oil lubricant. It also enables one to understand the operating material removal mechanisms responsible for the observed wear characteristics of the samples under varying test conditions. The investigation helps one to see that only a critical concentration of the solid lubricant particles in oil can lead to the best wear performance of materials.

From a practical standpoint, the observations made here gain importance from the fact that solid lubricants are added frequently in oil in engineering applications but it becomes imperative to understand that only a critical concentration can lead to the best wear behaviour of materials.

Economic pressures are driving fleets to substantially increase their maintenance intervals. To meet this challenge, both the original equipment manufacturers (OEM) and the lubricant suppliers have developed new and better products to give users the benefits of extended service intervals while at the same time maintaining equipment life and reducing operating costs. This paper will examine the options available in formulating extended drain transmission and axle lubricants by comparing four products designed to meet the OEM extended service interval requirements. Bench test and field test data will be reviewed which show that by optimizing the base oil as well as the additive system, both synthetic as well as properly formulated mineral oil products can give excellent extended drain performance. With mounting economic pressures in the trucking industry, these new products will give maintenance personnel additional product choices as they move their fleets to extended drain transmission and axle lubricants in an effort to safely extend equipment life and reduce total maintenance costs.

The purpose of this paper is to investigate alternatives for four stroke 10w40 motorcycle engine oils. Today, mineral and synthetic‐based lubricants are widely used but because of ecological aspects, which are gaining in importance nowadays and limited resources of mineral oils, environmentally‐friendly biobased lubricants are gaining in importance. Biobased lubricants are also important for using national resources rather than importing crude oils which are limited. The main consumption of lubricant market is motor oils. In this study, starting from mineral, synthetic and biobased lubricants; mineral, synthetic, biomineral and biosynthetic based four stroke motorcycle engine oils (10w40) are prepared, then lubricity properties of the motor oils are determined.

The lubricity tests of the samples are done in a fixed forced lubricity test rig and the motorcycle motor oil preparation are conducted according to ASTM test methods.

The results show that 5 per cent of biobased lubricants will be suitable for preparing 10w40 motor oils in both mineral and synthetic based motor oils. Also improvements in the lubricity properties with the blend with biobased lubricants are seen.

The paper presents biomineral and biosynthetic 10w40 motor oils as alternative candidates for motorcycle motor oils.