Search results

This paper aims to design an active shock absorber scheme for use in conjunction with a passive shock absorber to suppress the horizontal vibration of elevator cars in a smaller range and shorter time. The developed active shock absorber will also improve the safety and comfort of passengers driving in ultra-high-speed elevators.

A six-degree of freedom dynamic model is established according to the position and condition of the car. Then the active shock absorber and disturbance compensation-based adaptive control scheme are designed and simulated in MATLAB/Simulink. The results are analysed and compared with the traditional shock absorber.

The results show that, compared with traditional spring-based passive damping systems, the designed active shock absorber can reduce vibration displacement by 60%, peak acceleration by 50% and oscillation time by 2/3 and is more robust to different spring stiffness, damping coefficient and load.

The developed active shock absorber and its control algorithm can significantly reduce vibration amplitude and converged time. It can also adjust the damping strength according to the actual load of the elevator car, which is more suitable for high-speed elevators.

The purpose of this study is to numerically model the rigid pavement resting on two-parameter soil and to examine its modal parameters.

This study is carried out using a one-dimensional beam element with three rotational and three translational degrees of freedom based on the finite element method. MATLAB programming is used to perform the free vibration analysis of the rigid pavement.

Cyclic frequency and their corresponding mode shapes were determined. It has been investigated how cyclic frequency changes as a result of variations in the thickness, span length of pavement, shear modulus, modulus of subgrade, different boundary conditions and element discretization. Thickness of the pavement and span length has greater effect on the cyclic frequency. Maximum increase of 29.7% is found on increasing the thickness, whereas the cyclic frequency decreases by 63.49% on increasing span length of pavement.

The pavement's free vibration is the sole subject of the current investigation. This study limits for the preliminary design phase of rigid pavements, where a complete three-dimensional finite element analysis is unnecessary. The current approach can be extended to future research using a different method, such as finite element grilling technique, mesh-free technique on reinforced concrete pavements or jointed concrete pavements.

The finite element approach adopted in this paper involves six degrees of freedom for each node. Furthermore, to the best of the authors’ knowledge, no prior study has done seven separate parametric investigations on the modal analysis of rigid pavement resting on two-parameter soil.

This paper aims to analyze deeply the effect of surface roughness conditions of the common interface of the two-layered riveted cantilever beams on their frictional damping during free lateral vibration at first mode. Here, the product, (µ × α), and damping ratio, ξ, are the parameters whose variations are analyzed in this investigation. For this, the influencing parameters considered are the natural frequency of vibration, f; the amplitude of initial excitation, y; and surface roughness value, Ra.

For experimentally evaluating logarithmic damping decrement, d, the frequency response function analyzer for the case of free lateral vibrations was used. Later, for evaluating the product, µ × α (where µ is the kinematic coefficient of friction and α is the dynamic slip ratio), and then, the damping ratio, ξ, the empirical relation suggested for logarithmic damping decrement, d, of riveted cantilever beams was used. After this, the full and reduced quadratic models of the product, µ × α, ξ, response surface methodology (RSM) with the help of Design Expert 11 software was used. Corresponding main effects plots, surface plots and prediction comparison plots were obtained to observe the variations of the product, µ × α, ξ for the variations of influencing parameters: f, y and Ra. Finally, a machine learning technique such as artificial neural networks (ANNs) using “nntool” present in MATLAB R13a software was used to predict the ξ for the different combinations of f, y and Ra.

The full and reduced quadratic regression models for the product, (µ × α) and the damping ratio, ξ of riveted cantilever beams for free lateral vibrations of the first mode in terms of the parameters: f, y and Ra were obtained. In addition, the main effects plots, surface plots and prediction comparison plots for the product, µ × α, ξ, with the corresponding experimental values of the product, µ × α, ξ, were obtained. Also, the execution of ANNs using MATLAB R13a software is proved to be the more accurate tool for the prediction of damping ratios in comparison to quadratic regression equations obtained from Design Expert 11 software. In the end, the assumption that the effect of surface roughness value on the product, (µ × α), and the damping ratio, ξ, is negligible is proved to be true using the main effects plots for the product, (µ × α) and ξ obtained from the Design Expert 11 software.

Obtaining the full and reduced quadratic regression equations for the product, (µ × α), and ξ of the two-layered riveted cantilever beams in terms of parameters: f, y and Ra was done. In addition, the conditions for the corresponding minimum and maximum values of the product, (µ × α), and ξ were obtained. Later, the main effects plots, surface plots and comparison plots of the predicted product, (µ × α), and ξ versus experimental product, (µ × α), and ξ were also obtained. Finally, the predicted values of the product, (µ × α), and ξ using the ANNs tool are observed to be the more accurate values in comparison to that obtained from RSM using the Design Expert 11 software.

This paper aims to compare and evaluate the influence of package designs and characteristics on the mechanical reliability of electronic assemblies when subjected to harmonic vibrations.

Using finite element analysis (FEA), the effect of package design-related parameters, including the interconnect array configuration, i.e. full vs perimeter, and package size, on solder mechanical stresses are fully addressed.

The results of FEA simulations revealed that the number of solder rows or columns available in the array, could significantly affect solder stresses. In addition, smaller packages result in lower solder stresses and differing distributions.

In literature, there are no papers that discuss the effect of solder array layout on electronic packages vibration reliability. In addition, general rules for designing electronic assemblies subjected to harmonic vibration loadings are proposed in this paper.

The purpose of this paper is to present the influence of inter-turn short circuit faults (ITSF) on electromagnetic vibration in high-voltage line-starting permanent magnet synchronous motor (HVLSPMSMS).

In this paper, the ampere–conductor wave model of HVLSPMSM after ITSF is established. Second, a mathematical model of the magnetic field after ITSF is established, and the influence law of the ITSF on the air-gap magnetic field is analyzed. Further, the mathematical expression of the electromagnetic force density is established based on the Maxwell tensor method. The impact of HVLSPMSM torque ripple frequency, radial electromagnetic force spatial–temporal distribution and rotor unbalanced magnetic tension force by ITSF is revealed. Finally, the electromagnetic–mechanical coupling model of HVLSPMSM is established, and the vibration spectra of the motor with different degrees of ITSF are solved by numerical calculation.

In this study, it is found that the 2np order flux density harmonics and (2 N + 1) p order electromagnetic forces are not generated when ITSF occurs in HVLSPMSM.

By analyzing the multi-harmonics of HVLSPMSM after ITSF, this paper provides a reliable method for troubleshooting from the perspective of vibration and torque fluctuation and rotor unbalanced electromagnetic force.

This study aims to investigate the morphing concepts able to manipulate the dynamics of the downstream unsteadiness in the separated shear layers and, in the wake, be able to modify the upstream shock–boundary layer interaction (SBLI) around an A320 morphing prototype to control these instabilities, with emphasis to the attenuation or even suppression of the transonic buffet. The modification of the aerodynamic performances according to a large parametric study carried out at Reynolds number of 4.5 × 10⁶, Mach number of 0.78 and various angles of attack in the range of (0, 2.4)° according to two morphing concepts (travelling waves and trailing edge vibration) are discussed, and the final benefits in aerodynamic performance increase are evaluated.

This article examines through high fidelity (Hi-Fi) numerical simulation the effects of the trailing edge (TE) actuation and of travelling waves along a specific area of the suction side starting from practically the most downstream position of the shock wave motion according to the buffet and extending up to nearly the TE. The present paper studies through spectral analysis the coherent structures development in the near wake and the comparison of the aerodynamic forces to the non-actuated case. Thus, the physical mechanisms of the morphing leading to the increase of the lift-to-drag ratio and the drag and noise sources reduction are identified.

This study investigates the influence of shear-layer and near-wake vortices on the SBLI around an A320 aerofoil and attenuation of the related instabilities thanks to novel morphing: travelling waves generated along the suction side and trailing-edge vibration. A drag reduction of 14% and a lift-to-drag increase in the order of 8% are obtained. The morphing has shown a lift increase in the range of (1.8, 2.5)% for angle of attack of 1.8° and 2.4°, where a significant lift increase of 7.7% is obtained for the angle of incidence of 0° with a drag reduction of 3.66% yielding an aerodynamic efficiency of 11.8%.

This paper presents results of morphing A320 aerofoil, with a chord of 70cm and subjected to two actuation kinds, original in the state of the art at M = 0.78 and Re = 4.5 million. These Hi-Fi simulations are rather rare; a majority of existing ones concern smaller dimensions. This study showed for the first time a modified buffet mode, displaying periodic high-lift “plateaus” interspersed by shorter lift-decrease intervals. Through trailing-edge vibration, this pattern is modified towards a sinusoidal-like buffet, with a considerable amplitude decrease. Lock-in of buffet frequency to the actuation is obtained, leading to this amplitude reduction and a drastic aerodynamic performance increase.

The purpose of this paper was to study the possibility of using smartphone roughness measurements for developing pavement roughness regression models as a function of pavement age, traffic loading and traffic volume variables. Also, the effects of patching and pavement distresses on pavement roughness were investigated. The work focused on establishing pavement roughness prediction models and applying these models to pavement management systems (PMS) to help decision-makers choose the best maintenance and rehabilitation (M&R) options by using cost-effective methods.

Signal processing techniques including filtering and processing techniques were used to obtain the International Roughness Index (IRI) from raw acceleration data collected from smartphone accelerometer sensors. The obtained IRI values were inputted as a dependent variable in analytical regression models as well as several independent variables with proper transformations.

According to the study results, several regression models were developed with a big variation in the coefficients of determination (R²). However, the best models included pavement age, accumulated traffic volume (∑TV) and construction quality factor (CQF) with R² equal to 0.63. It was also found that the effects of pavement distresses and patching was significant at a-level < 0.05. The patching effect on pavement roughness was found higher than the effect of other pavement distresses.

The presented results and methods in this paper could be used in the future predictions of pavement roughness and help the decision-makers to estimate M&R needs. The work focused on establishing IRI prediction models and applying these models to the PMS to help decision-makers choose the best M & R options.

To develop sound pavement roughness models, it is essential to collect roughness data using automated procedures. However, applying these procedures in developing countries faces several difficulties such as the high price and operation costs of roughness equipment and lack of technical experience. The advantage of using IRI values taken from smartphones is that the roughness evaluation survey may be expanded to cover the full road network at a cheaper cost than with automated instruments. Therefore, if the roughness survey covers more roads, the prediction model’s accuracy will be improved.

The purpose of this paper is to investigate the vehicle-based sensor effect and pavement temperature on road condition assessment, as well as to compute a threshold value for the classification of pavement conditions.

Four sensors were placed on the vehicle’s control arms and one inside the vehicle to collect vibration acceleration data for analysis. The Analysis of Variance (ANOVA) tests were performed to diagnose the effect of the vehicle-based sensors’ placement in the field. To classify road conditions and identify pavement distress (point of interest), the probability distribution was applied based on the magnitude values of vibration data.

Results from ANOVA indicate that pavement sensing patterns from the sensors placed on the front control arms were statistically significant, and there is no difference between the sensors placed on the same side of the vehicle (e.g., left or right side). A reference threshold (i.e., 1.7 g) was computed from the distribution fitting method to classify road conditions and identify the road distress based on the magnitude values that combine all acceleration along three axes. In addition, the pavement temperature was found to be highly correlated with the sensing patterns, which is noteworthy for future projects.

The paper investigates the effect of pavement sensors’ placement in assessing road conditions, emphasizing the implications for future road condition assessment projects. A threshold value for classifying road conditions was proposed and applied in class assignments (I-17 highway projects).

Nowadays, in building structures, dampers are connected to the building structure to reduce the damages caused by seismicity in addition to enhancing structural stability, and to connect dampers with the structure, joints are used. In this paper, three different configurations of double-lap joints were designed, developed and tested.

This paper aims to analyze three different categories of double-lap single-bolted joints that are used in connecting dampers with concrete and steel frame structures. These joints were designed and tested using computational, numerical and experimental methods. The studies were conducted to examine the reactions of the joints during loading conditions and to select the best joints for the structures that allow easy maintenance of the dampers and also withstand structural deformation when the damper is active during seismicity. Also, a computational analysis was performed on the designed joints integrated with the M25 concrete beam column junction. In this investigation, experimental study was carried out in addition to numerical and computational methods during cyclic load.

It was observed from the result that during deformation the double-base multiplate lap joint was suitable for buildings because the deformations on the joint base was negligible when compared with other joints. From the computational analysis, it was revealed that the three double joints while integrated with the beam column junction of M25 grade concrete structure, the damages induced by the double-base multiplate joint was negligible when compared with other two joints used in this study.

To prevent the collapse of the building during seismicity, dampers are used and further connecting the damper with the building structures, joints are used. In this paper, three double-lap joints in different design configuration were studied using computational, numerical and experimental techniques.

Surface roughness has a serious impact on the fatigue strength, wear resistance and life of mechanical products. Realizing the evolution of surface quality through theoretical modeling takes a lot of effort. To predict the surface roughness of milling processing, this paper aims to construct a neural network based on deep learning and data augmentation.

This study proposes a method consisting of three steps. Firstly, the machine tool multisource data acquisition platform is established, which combines sensor monitoring with machine tool communication to collect processing signals. Secondly, the feature parameters are extracted to reduce the interference and improve the model generalization ability. Thirdly, for different expectations, the parameters of the deep belief network (DBN) model are optimized by the tent-SSA algorithm to achieve more accurate roughness classification and regression prediction.

The adaptive synthetic sampling (ADASYN) algorithm can improve the classification prediction accuracy of DBN from 80.67% to 94.23%. After the DBN parameters were optimized by Tent-SSA, the roughness prediction accuracy was significantly improved. For the classification model, the prediction accuracy is improved by 5.77% based on ADASYN optimization. For regression models, different objective functions can be set according to production requirements, such as root-mean-square error (RMSE) or MaxAE, and the error is reduced by more than 40% compared to the original model.

A roughness prediction model based on multiple monitoring signals is proposed, which reduces the dependence on the acquisition of environmental variables and enhances the model's applicability. Furthermore, with the ADASYN algorithm, the Tent-SSA intelligent optimization algorithm is introduced to optimize the hyperparameters of the DBN model and improve the optimization performance.