Search results

The purpose of this study is to investigate the effect of electron beam surface melting (EBSM) on the properties of Plasma Transfer Arc (PTA) deposited Stellite 12 hardfacing.

For this purpose, structural characterization and dry sliding wear tests have been conducted on the hardfacings at room temperature. The wear tracks formed on the surfaces of the hardfacings were examined by a stylus-type profilometer and a scanning electron microscope.

Refinement of the matrix and the carbides following EBSM process led to about 15 per cent increment in hardness as compared to PTA state. Despite an increase in the surface hardness, EBSM’ed hardfacing exhibited about 50 per cent lower sliding wear resistance than PTA hardfacing against alumina ball. According to the worn surface examinations, reduction in the wear resistance of Stellite 12 after EBSM process has been associated with the extensive refinement of the carbides which made them easier to be removed from the matrix during the sliding contact.

The authors of current study have applied EBSM to PTA deposited Stellite 12 hardfacing alloy to investigate if the surface structure and properties could be improved. More specifically the dry sliding wear performance of PTA and EBSM’ed hardfacings have been focused in the scope of this study. To the best of the authors’ knowledge, this approach, i.e. use of EBSM as a post deposition treatment of Stellite 12 hardfacings, has not been reported in open literature.

The purpose of the study is to examine the sliding wear performance of plasma transfer arc (PTA) deposited and laser surface melted (LSM) Mo modified Stellite 12 hardfacings under high contact stresses (i.e. >20 GPa).

For this purpose, after structural characterization, sliding wear tests have been conducted using sphero-conical diamond indenter as the counterface with different normal loads. The wear tracks formed on the hardfacings were examined by atomic force microscopy and scanning electron microscopy.

Both hardfacings showed severe wear (at high contact stress levels ranging from 24 to 41 GPa), which progressed by plastic deformation, although the wear resistance of LSMed hardfacings was better than the PTA hardfacings by a factor of two due to its near surface microstructure characterized as carbide-rich zone.

Sliding wear characterization of a promising 10 Wt.% Mo modified version of commercial Stellite 12 hardfacings (as reported previously by authors) was done in as PTA and LSMed states using nanomechanical test system. To the best of authors’ knowledge, no report is available in the open literature on such hardfacings under these testing conditions.

Hardsurfacing with Ni/Cr‐base alloys gives additional advantages in protection against corrosion and atmospheric and high‐temperature oxidation. The latter effects frequently contribute greatly to the rate of wear. The self‐fluxing characteristics of such boron‐containing alloys, coupled with a wide melting range, enables the coating of contoured surfaces and application by spraying and fusing. Using a bonding agent very thin protective coatings may be applied by furnace fusion.

This paper aims to present a comparative study of the wear properties of ferrous welded materials like EN8, EN9 and mild steel (MS).

The material is cut into specific dimension after hardfacing and is studied for the wear properties of the material. The wear testing is done on a pin-on-disc apparatus. The microhardness of the material is studied using the Vickers microhardness measuring apparatus.

The wear properties of ferrous welded materials like EN8, EN9 and MS are studied. It is found the MS has the least wear when compared to EN8 and EN9. The microhardness of MS is higher than EN8 and EN9, thus making it more wear-resistant than EN8 and EN9. The coefficient of friction in the dry sliding condition is found to be constant throughout the experiment.

Major restriction is the amount of time required for use-wear analysis and replication experiments that are necessary to produce reliable results. These limitations mean that the analysis of total assemblages with the intention of producing specific results, especially of worked materials, is not feasible.

Generally, the complexity and rigour of the analysis depend primarily on the engineering needs and secondarily on the wear situation. It has been the author’s experience that simple and basic wear analyses, conducted in the proper manner, are often adequate in many engineering situations. Integral and fundamental to the wear analysis approach is the treatment of wear and wear behaviour as a system property. As a consequence, wear analysis is not limited to the evaluation of the effects of materials on wear behaviour. Wear analysis often enables the identification of nonmaterial solutions or nonmaterial elements in a solution to wear problems. For example, changes in or recommendations for contact geometry, roughness, tolerance and so on are often the results of a wear analysis.

The value of the work lies in the utility of the results obtained to researchers and users of the EN8, EN9 and EN24 material for their components.

This paper aims to study microstructure and high temperature tribological performance of hypo-eutectic CoCrWC hardfacing alloy (Stellite 12) deposited on steel substrate by plasma-transferred arc (PTA) welding technique.

Microstructural characterization of the deposited coating was made using electron probe microanalysis, X-ray diffraction and microhardness tester. Dry sliding wear tests were carried out with a ball-on-disc type tribometer at room and elevated temperature. Worn surfaces of the samples were examined by the EDX equipped SEM and Raman spectroscopy.

Results revealed that at room temperature and 300°C plasticity dominated wear mechanism was operative. Under oxidation dominated wear conditions (400, 500, 600 and 700°C), testing temperature plays a crucial role on the characteristics of the oxide tribolayers formed on worn surfaces. Development of Cr2O3 in the tribolayer at 600 and 700°C was beneficial in increasing wear resistance of examined coating.

While the sliding wear performance of Stellite alloys at room temperature has been investigated in details, published studies on tribological behavior of Stellite alloys with varying temperature are scarce. Therefore, the present work was undertaken to study the wear mechanisms and the type of tribolayers formed during sliding wear of PTA welding deposited hypo-eutectic Stellite 12 coating with increasing temperature up to 700°C.

TWI, as The Welding Institute prefers to be called these days, is one of the success stories of the late 1980s. At a time when many research associations were suffering decline TWI has expanded both technically and commercially. At its open days last June it presented an air of quiet confidence to its many visistors.

Platinised Titanium Anodes. Platinised titanium anodes have been developed and introduced for protection of condenser water boxes and the internal protection of pipelines.

The present work aims at developing the laser cladding technology by means of an active fiber laser source applicable for hardfacing of martensitic steel turbine blades. It also aims to investigate two process parameter conditions to reproduce two different heat inputs, in order to highlight the effect of the thermal input on the thermal alteration and dilution of the substrate material and clad layer.

The experimentation was performed initially at a sample level, reproducing the material and thickness of the blade leading edge, then on an industrial real component. Cladding process parameters were experimentally selected and two different process parameter conditions, at different specific energy, were determined. The microstructural and geometrical features of the clad samples were analyzed both by optical microscopy and scanning electron microscopy, in this latter case combining the information supplied by different probes, among which the EDX microanalysis to obtain chemical profiles. Hardness distribution was also evaluated by means of Vickers hardness tester.

All the two investigated conditions were suitable for laser cladding of the blade leading edge, since a crack and pore free clad layer with a strong metallurgical bond to the substrate was obtained. The experimented two different heat inputs affected the extension of the HAZ as well the chemical and geometrical dilution. The clad integrity was preserved in both cases. The condition at higher specific energy was chosen to clad the turbine blade. The high specific energy condition was preferred because the iron dilution in the clad layer was inferior.

Further research is needed to correlate the chemical dilution and the thermal alteration introduced by the laser cladding process on such a kind of substrate at different process parameter conditions to the wear and corrosion resistance of the turbine blade.

Laser cladding process with an innovative active fiber laser source of the leading edge of a steam turbine blade was developed. Progress achieved in laser cladding technology development is of practical value for manufacture of turbine blades, made of martensitic steels.

The paper investigates the effect of different energy input on the laser cladding of steam turbine blades, mainly used in coal, gas and nuclear plants to produce electricity by heating water to create steam. The laser cladding process is an effective technology to increase the steam blades toughness and resistance to creep, stress and corrosion. This increase in the turbine blade properties contributes to extend the life of such a critical components, decreasing cost and time of substitution and ensuring better service conditions.

The most original aspect of the paper is related to the focus on the difference between the chemical and the geometrical dilution, being the first one mainly related to the corrosion and wear resistance of the clad layer, while the later mainly regards the clad layer adhesion to the substrate. More in general the paper presents one of the first experiments accomplished while making use of the active fiber laser source.