Search results
1 – 10 of over 1000Ali Abdul Munim Alhattab, Shaikh Asad Ali Dilawary, Amir Motallebzadeh, Cevat Fahir Arisoy and Huseyin Cimenoglu
The purpose of this study is to investigate the effect of electron beam surface melting (EBSM) on the properties of Plasma Transfer Arc (PTA) deposited Stellite 12 hardfacing.
Abstract
Purpose
The purpose of this study is to investigate the effect of electron beam surface melting (EBSM) on the properties of Plasma Transfer Arc (PTA) deposited Stellite 12 hardfacing.
Design/methodology/approach
For this purpose, structural characterization and dry sliding wear tests have been conducted on the hardfacings at room temperature. The wear tracks formed on the surfaces of the hardfacings were examined by a stylus-type profilometer and a scanning electron microscope.
Findings
Refinement of the matrix and the carbides following EBSM process led to about 15 per cent increment in hardness as compared to PTA state. Despite an increase in the surface hardness, EBSM’ed hardfacing exhibited about 50 per cent lower sliding wear resistance than PTA hardfacing against alumina ball. According to the worn surface examinations, reduction in the wear resistance of Stellite 12 after EBSM process has been associated with the extensive refinement of the carbides which made them easier to be removed from the matrix during the sliding contact.
Originality/value
The authors of current study have applied EBSM to PTA deposited Stellite 12 hardfacing alloy to investigate if the surface structure and properties could be improved. More specifically the dry sliding wear performance of PTA and EBSM’ed hardfacings have been focused in the scope of this study. To the best of the authors’ knowledge, this approach, i.e. use of EBSM as a post deposition treatment of Stellite 12 hardfacings, has not been reported in open literature.
Details
Keywords
Ya Qian, Wentao Yan and Feng Lin
This paper aims to study the effect of processing parameters and the fundamental mechanism of surface morphologies during electron beam selective melting.
Abstract
Purpose
This paper aims to study the effect of processing parameters and the fundamental mechanism of surface morphologies during electron beam selective melting.
Design/methodology/approach
From the powder-scale level, first, the discrete element method is used to obtain the powder bed distribution that is comparable with the practical condition; then, the finite volume method is used to simulate the particle melting and flowing process. A physically reliable energy distribution of the electron beam is applied and the volume of fluid method is coupled to capture the free boundary flow. Twelve sets of parameters grouped into three categories are examined, focusing on the effect of scan speed, input powder and energy density.
Findings
According to the results, both melting pool width and depth have a positive relation with the energy density, whereas the melting pool length is insensitive to the scan velocity change. The balling effect is attributed to either an insufficient energy input or the flow instability; the hump effect originates from the mismatch between electron beam moving and the fluid flow. The scan speed is a key parameter closely related to melting pool size and surface morphologies.
Originality/value
Through a number of case studies, this paper gives a comprehensive insight of the parameter effects and mechanisms of different surface morphologies, which helps to better control the manufacturing quality of electron beam selective melting.
Details
Keywords
Ashfaq Mohammad, Abdurahman Mushabab Al-Ahmari, Abdullah AlFaify and Muneer Khan Mohammed
Electron beam melting (EBM) is one of the potential additive manufacturing technologies to fabricate aero-engine components from gamma titanium aluminide (γ-TiAl) alloys. When a…
Abstract
Purpose
Electron beam melting (EBM) is one of the potential additive manufacturing technologies to fabricate aero-engine components from gamma titanium aluminide (γ-TiAl) alloys. When a new material system has to be taken in to the fold of EBM, which is a highly complex process, it is essential to understand the effect of process parameters on the final quality of parts. This paper aims to understand the effect of melting parameters on top surface quality and density of EBM manufactured parts. This investigation would accelerate EBM process development for newer alloys.
Design/methodology/approach
Central composite design approach was used to design the experiments. In total, 50 specimens were built in EBM with different melt theme settings. The parameters varied were surface temperature, beam current, beam focus offset, line offset and beam speed. Density and surface roughness were selected as responses in the qualifying step of the parts. After identifying the parameters which were statistically significant, possible reasons were analyzed from the perspective of the EBM process.
Findings
The internal porosity and surface roughness were correlated to the process settings. Important ones among the parameters are beam focus offset, line offset and beam speed. By jointly deciding the total amount of energy input for each layer, these three parameters played a critical role in internal flaw generation and surface evolution.
Research limitations/implications
The range selected for each parameter is applicable, in particular, to γ-TiAl alloy. For any other alloy, the settings range has to be suitably adapted depending on physical properties such as melting point, thermal conductivity and thermal expansion co-efficient.
Practical implications
This paper demonstrates how melt theme parameters have to be understood in the EBM process. By adopting a similar strategy, an optimum window of settings that give best consolidation of powder and better surface characteristics can be identified whenever a new material is being investigated for EBM. This work gives researchers insights into EBM process and speeds up EBM adoption by aerospace industry to produce critical engine parts from γ-TiAl alloy.
Originality/value
This work is one of the first attempts to systematically carry out a number of experiments and to evaluate the effect of melt parameters for producing γ-TiAl parts by the EBM process. Its conclusions would be of value to additive manufacturing researchers working on γ-TiAl by EBM process.
Details
Keywords
Rebecca Klingvall Ek, Lars-Erik Rännar, Mikael Bäckstöm and Peter Carlsson
The surface roughness of products manufactured using the additive manufacturing (AM) technology of electron beam melting (EBM) has a special characteristic. Different product…
Abstract
Purpose
The surface roughness of products manufactured using the additive manufacturing (AM) technology of electron beam melting (EBM) has a special characteristic. Different product applications can demand rougher or finer surface structure, so the purpose of this study is to investigate the process parameters of EBM to find out how they affect surface roughness.
Design/methodology/approach
EBM uses metal powder to manufacture metal parts. A design of experiment plan was used to describe the effects of the process parameters on the average surface roughness of vertical surfaces.
Findings
The most important electron beam setting for surface roughness, according to this study, is a combination of “speed and current” in the contours. The second most important parameter is “contour offset”. The interaction between the “number of contours” and “contour offset” also appears to be important, as it shows a much higher probability of being active than any other interaction. The results show that the “line offset” is not important when using contours.
Research limitations/implications
This study examined “contour offset”, “number of contours”, “speed in combination with current” and “line offset”, which are process parameters controlling the electron beam.
Practical implications
The surface properties could have an impact on the product’s performance. A reduction in surface processing will not only save time and money but also reduce the environmental impact.
Originality/value
Surface properties are important for many products. New themes containing process parameters have to be developed when introducing new materials to EBM manufacturing. During this process, it is very important to understand how the electron beam affects the melt pool.
Details
Keywords
Dana H. Abdeen and Bruce R. Palmer
This paper aims to study the effect of processing parameters of an electron beam melting (EBM) machine on the surface roughness, critical pitting temperature and density of…
Abstract
Purpose
This paper aims to study the effect of processing parameters of an electron beam melting (EBM) machine on the surface roughness, critical pitting temperature and density of Ti-6Al-4V parts produced from the EBM machine.
Design/methodology/approach
In this study, statistically designed experiments were used to manufacture Ti-6Al-4V samples in the EBM machine under different process parameters of beam current, beam speed and offset focus. Surface roughness was measured for as-built samples using a 3D profilometer. Then, a potentiostatic test was conducted under 2.40 V vs saturated calomel electrode to determine the critical pitting temperature (CPT) in 3.5 per cent mass NaCl solution for the samples of different processing parameters. Next, density was measured for these samples. Finally, model equations were established to relate EBM’s process parameters to measured properties of surface roughness, CPT and density.
Findings
Results showed that offset focus had the main influence on surface roughness more than the beam current and the beam speed. Changing processing parameters did not affect corrosion behavior of EBM Ti-6Al-4V as CPT did not vary widely, although a slight effect on CPT values obtained from the beam current and the beam speed. Density was greatly affected by the offset focus more than the other parameters. It can be concluded that uniform and precise measurements of roughness and density are not achievable through this machine; only a range of these properties can be attained.
Originality/value
EBM machine produces 3D parts in a layer-based building process under high temperature and vacuum atmosphere. Due to the manufacturing technique and conditions, the resulting object has irregularities on the exterior surface and voids that are formed within the part, both of which affect samples’ properties like surface roughness, CPT and density. This study established model equations that can relate parts’ properties to processing parameters so that parts of specific properties are obtained to fit the application they are used for. For each property, ANOVA fits vs linear energy were also obtained.
Details
Keywords
Wahyudin P. Syam, Huda A. Al‐Shehri, A.M. Al‐Ahmari, Khalid A. Al‐Wazzan and M.A. Mannan
The purpose of this paper is to investigate the potential application of electron beam melting, as a layered manufacturing process, to fabricate dental coping of metal‐ceramic…
Abstract
Purpose
The purpose of this paper is to investigate the potential application of electron beam melting, as a layered manufacturing process, to fabricate dental coping of metal‐ceramic crown restoration using Ti6Al4V powder.
Design/methodology/approach
This experiment was conducted in two steps: shrinkage study to determine scale up factor for shrinkage compensation and parameter selection study, based on thickness, hardness, and surface roughness, to select process parameter of electron beam melting.
Findings
A promising result of fabricating metal coping of Ti6Al4V via electron beam melting was shown. Ti6Al4V coping was successfully fabricated, with an average thickness of 0.52 mm required for dental coping. Total average hardness of 333.35 HV that is comparable to casted Ti6Al4V with considerably high roughness of RSm of 382 μm.
Originality/value
The paper presents a novel application of electron beam melting to fabricate metal coping for metal‐ceramic crown restoration.
Details
Keywords
Kashif Ishfaq, Mudassar Rehman, Ahmed Raza Khan and Yanen Wang
Human aging is becoming a common issue these days as it results in orthopaedic-related issues such as joints disorderness, bone-fracture. People with age = 60 years suffer more…
Abstract
Purpose
Human aging is becoming a common issue these days as it results in orthopaedic-related issues such as joints disorderness, bone-fracture. People with age = 60 years suffer more from these aforesaid issues. It is expected that these issues in human beings will ultimately reach 2.1 billion by 2050 worldwide. Furthermore, the increase in traffic accidents in young people throughout the world has significantly emerged the need for artificial implants. Their implantation can act as a substitute for fractured bones or disordered joints. Therefore, this study aims to focus on electron beam melted titanium (Ti)-based orthopaedic implants along with their recent trends in the field.
Design/methodology/approach
The main contents of this work include the basic theme and background of the metal-based additive manufacturing, different implant materials specifically Ti alloys and their classification based on crystallographic transus temperature (including α, metastable β, β and α + β phases), details of electron beam melting (EBM) concerning its process physics, various control variables and performance characteristics of EBMed Ti alloys in orthopaedic and orthodontic implants, applications of EBMed Ti alloys in various load-bearing implants, different challenges associated with the EBMed Ti-based implants along with their possible solutions. Recent trends and shortfalls have also been described at the end.
Findings
EBM is getting significant attention in medical implants because of its minor issues as compared to conventional fabrication practices such as Ti casting and possesses a significant research potential to fabricate various medical implants. The elastic modulus and strength of EBMed ß Ti-alloys such as 24Nb-4Zr-8Sn and Ti-33Nb-4Sn are superior compared to conventional Ti for orthopaedic implants. Beta Ti alloys processed by EBM have near bone elastic modulus (approximately 35–50 GPa) along with improved tribo-mechanical performance involving mechanical strength, wear and corrosion resistance, along with biocompatibility for implants.
Originality/value
Advances in EBM have opened the gateway Ti alloys in the biomedical field explicitly ß-alloys because of their unique biocompatibility, bioactivity along with improved tribo-mechanical performance. Less significant work is available on the EBM of Ti alloys in orthopaedic and orthodontic implants. This study is directed solely on the EBM of medical Ti alloys in medical sectors to explore their different aspects for future research opportunities.
Details
Keywords
Luca Facchini, Emanuele Magalini, Pierfrancesco Robotti and Alberto Molinari
The purpose of this paper is the microstructural and mechanical characterization of a biomedical Ti‐6Al‐4V alloy produced by electron beam melting, and the study of the stability…
Abstract
Purpose
The purpose of this paper is the microstructural and mechanical characterization of a biomedical Ti‐6Al‐4V alloy produced by electron beam melting, and the study of the stability of the as‐built microstructure upon heat treatment.
Design/methodology/approach
Ti‐6Al‐4V alloy produced by electron beam melting has been mechanically characterized through tensile and fatigue testing. Its microstructure has been investigated by optical observation after etching and by X‐ray diffractometry analysis. The stability of the microstructure of the as‐built material has been deepened carrying out suitable heat treatments, after an analysis by dilatometry test.
Findings
The microstructure of a Ti‐6Al‐4V alloy produced by electron beam melting has a very fine and acicular morphology, because of the intrinsically high‐solidification rate of the process. This microstructure is very stable, and the traditional thermal treatments cannot modify it; the microstructure changes significantly only when an amount of strain is introduced in the material. However, the mechanical properties of the alloy produced by electron beam melting are good.
Originality/value
The paper provides evidence of the microstructural stability of the material produced by electron beam melting. Even if the microstructure of the as‐built material is not recommended by the specific ISO standard, the related mechanical properties are fully satisfactory. This is a significant indication from the point of view of the production of Ti‐6Al‐4V orthopaedic and dental prostheses by electron beam melting.
Details
Keywords
Guanchen Liu, Dongdong Xu, Zifu Shen, Hongjie Xu and Liang Ding
As an advanced manufacturing method, additive manufacturing (AM) technology provides new possibilities for efficient production and design of parts. However, with the continuous…
Abstract
Purpose
As an advanced manufacturing method, additive manufacturing (AM) technology provides new possibilities for efficient production and design of parts. However, with the continuous expansion of the application of AM materials, subtractive processing has become one of the necessary steps to improve the accuracy and performance of parts. In this paper, the processing process of AM materials is discussed in depth, and the surface integrity problem caused by it is discussed.
Design/methodology/approach
Firstly, we listed and analyzed the characterization parameters of metal surface integrity and its influence on the performance of parts and then introduced the application of integrated processing of metal adding and subtracting materials and the influence of different processing forms on the surface integrity of parts. The surface of the trial-cut material is detected and analyzed, and the surface of the integrated processing of adding and subtracting materials is compared with that of the pure processing of reducing materials, so that the corresponding conclusions are obtained.
Findings
In this process, we also found some surface integrity problems, such as knife marks, residual stress and thermal effects. These problems may have a potential negative impact on the performance of the final parts. In processing, we can try to use other integrated processing technologies of adding and subtracting materials, try to combine various integrated processing technologies of adding and subtracting materials, or consider exploring more efficient AM technology to improve processing efficiency. We can also consider adopting production process optimization measures to reduce the processing cost of adding and subtracting materials.
Originality/value
With the gradual improvement of the requirements for the surface quality of parts in the production process and the in-depth implementation of sustainable manufacturing, the demand for integrated processing of metal addition and subtraction materials is likely to continue to grow in the future. By deeply understanding and studying the problems of material reduction and surface integrity of AM materials, we can better meet the challenges in the manufacturing process and improve the quality and performance of parts. This research is very important for promoting the development of manufacturing technology and achieving success in practical application.
Details
Keywords
Christoph R. Pobel, Fuad Osmanlic, Matthias A. Lodes, Sebastian Wachter and Carolin Körner
Selective electron beam melting (SEBM) is a highly versatile powder bed fusion additive manufacturing method. SEBM is characterized by high energy densities which can be applied…
Abstract
Purpose
Selective electron beam melting (SEBM) is a highly versatile powder bed fusion additive manufacturing method. SEBM is characterized by high energy densities which can be applied with nearly inertia free beam deflection at high speeds (<8.000 m/s). This paper aims to determine processing maps for Ti-6Al-4V on an Arcam Q10 machine with LaB6 cathode design.
Design/methodology/approach
Scan line spacings of 100, 50 and 20 µm in a broad parameter range, focusing on high deflection and build speeds are investigated.
Findings
There are broad processing windows for dense parts without surface flaws for all scan line spacings which are defined by the total energy input and the area melting velocity.
Originality/value
The differences and limitations are discussed taking into account the beam properties at high beam energy and velocity as well as evaporation related loss of alloying components.
Details