Search results

Wire-arc-based additive manufacturing (WAAM) is a promising technology for the efficient and economical fabrication of medium-large components. However, the anisotropic behavior of the multilayered WAAM-fabricated components remains a challenging problem.

The purpose of this paper is to conduct a comprehensive study of the grain morphology, crystallographic orientation and texture in three regions of the WAAM printed component. Furthermore, the interdependence of the grain morphology in different regions of the fabricated component with their mechanical and tribological properties was established.

The electron back-scattered diffraction analysis of the top and bottom regions revealed fine recrystallized grains, whereas the middle regions acquired columnar grains with an average size of approximately 8.980 µm. The analysis revealed a higher misorientation angle and an intense crystallographic texture in the upper and lower regions. The investigations found a higher microhardness value of 168.93 ± 1.71 HV with superior wear resistance in the bottom region. The quantitative evaluation of the residual stress detected higher compressive stress in the upper regions. Evidence for comparable ultimate tensile strength and greater elongation (%) compared to its wrought counterpart has been observed.

The study found a good correlation between the grain morphology in different regions of the WAAM-fabricated component and their mechanical and wear properties. The Hall–Petch relationship also established good agreement between the grain morphology and tensile test results. Improved ductility compared to its wrought counterpart was observed. The anisotropy exists with improved mechanical properties along the longitudinal direction. Moreover, cylindrical components have superior tribological properties compared with cuboidal components.

To orient the commercial development of cowpeas, we identify the determinants of the value of cowpea grain sold by traders in Senegal’s local markets. We test whether the determinants differ between men and women traders and explore seasonal patterns.

We employ ordinary least squares and seemingly unrelated regressions using a nationally representative dataset of 973 traders, of whom 380 sell cowpea grain, in 99 urban and rural markets across the 14 regions of Senegal.

The value of cowpea grain sold is influenced by vendor and market characteristics but not by cowpea type. Women and men traders represent statistically distinct groups. The sales value was eight times higher during the survey season among men. Most women grain sellers are retailers, whereas men are involved in both retailing and wholesaling. The picture that emerges is that men traders are able to respond more to economic signals, such as purchase cost, credit and labor payments, perhaps because they operate on a larger scale. Sales were significantly correlated across seasons.

To support cowpea commercialization, researchers should explore the characteristics of enterprises led by women and men traders in greater depth. Sampling grain sold in markets to test genetic relationships with improved varieties would enable researchers to link market-based incentives directly to cowpea breeding.

Previous economics research about cowpea grain markets emphasized the hedonic analysis of grain characteristics to guide crop improvement. This study reveals differentiation among traders by gender and the importance of trader and market characteristics in sales value.

This study aims to study the formation mechanism of micro-arc oxidation (MAO) coating on AZ31 magnesium alloy and how the annealing process affects its corrosion resistance.

This study involved immersion experiments, electrochemical experiments and slow strain rate tensile experiments, along with scanning electron microscopy, optical microscopy observation and X-ray diffraction analysis.

The findings suggest that annealing treatment can refine the grain size of AZ31 magnesium alloy to an average of 6.9 µm at 300°C. The change in grain size leads to a change in conductivity, which affects the performance of MAO coatings. The MAO coating obtained by annealing the substrate at 300°C has smaller pores and porosity, resulting in better adhesion and wear resistance.

The coating acts as a barrier to prevent corrosive substances from entering the substrate. However, the smaller pores and porosity reduce the channels for the corrosive solution to pass through the coating. When the coating cracks or falls off, the corrosive medium and substrate come into direct contact. Smaller and uniform grains have better corrosion resistance.

An experimental investigation for developing structure-property correlations of hot-rolled E410 steels with different carbon contents, i.e. 0.04wt.%C and 0.17wt.%C metal active gas (MAG) and cold metal transfer (CMT)-MAG weldments was undertaken.

Mechanical properties and microstructure of MAG and CMT-MAG weldments of two E410 steels with varying content of carbon were compared using standardized mechanical testing procedures, and conventional microscopy.

0.04wt.%C steel had strained ferritic and cementite sub-structures in blocky shape and large dislocation density, while 0.17wt.%C steel consisted of pearlite and polygonal ductile ferrite. This effected yield strength (YS), and microhardness being larger in 0.04wt.%C steel, %elongation being larger in 0.17wt.%C steel. Weldments of both E410 steels obtained with CMT-MAG performed better than MAG in terms of YS, ultimate tensile strength (UTS), %elongation, and toughness. It was due to low heat input of CMT-MAG that resulted in refinement of weld metal, and subzones of heat affected zone (HAZ).

A substantial improvement in YS (∼9%), %elongation (∼38%), and room temperature impact toughness (∼29%) of 0.04wt.%C E410 steel is achieved with CMT-MAG over MAG welding. Almost ∼10, ∼12.5, and ∼16% increment in YS, %elongation, and toughness of 0.17wt.%C E410 steel is observed with CMT-MAG. Relatively low heat input of CMT-MAG leads to development of fine Widmanstätten and acicular ferrite in weld metal and microstructural refinement in HAZ subzones with nearly similar characteristics of base metal.

This research aims to examine the impact of friction stir processing (FSP) treatment on an aluminum alloy, especially the AD31T alloy derived from the Al-Fe-Mg-Si system. The aim is to assess the influence of different processing techniques on the microstructure and physical and mechanical characteristics of the material, with a specific focus on structural and bulk imperfections inside the stir zone (SZ).

The study demonstrates that augmenting the linear velocity of the tool within the 25–100 mm/min range results in significant enhancements. The enhancements include a decrease in the heat-affected zone (HAZ), a reduction in the extent of volume defects inside the SZ and a more uniform deformation. The microstructural analysis results are corroborated by data acquired from microhardness and electrical conductivity studies, confirming the beneficial influence of modifying the tool’s linear velocity on the material parameters.

This study provides significant observations on the changes in microstructure and the generation of flaws throughout the process of FSP of AD31T alloy. These results have practical implications for improving the characteristics of the alloy and optimizing the production conditions.

All samples exhibit a distinct reduction in electrical conductivity within the initial third of the sample, aligning with the transitional region between the base metal (BM) and the HAZ. This underscores the importance of understanding the transitional zones during FSP.

The purpose of this paper is to determine the ultra-high cycle fatigue behavior and ultra-slow crack propagation behavior of selective laser melting (SLM) AlSi7Mg alloy under as-built conditions.

Constant amplitude and two-step variable amplitude fatigue tests were carried out using ultrasonic fatigue equipment. The fracture surface of the failure specimen was quantitatively analyzed by scanning electron microscope (SEM).

The results show that the competition of surface and interior crack initiation modes leads to a duplex S–N curve. Both manufacturing defects (such as the lack of fusion) and inclusions can act as initially fatal fatigue microcracks, and the fatigue sensitivity level decreases with the location, size and type of the maximum defects.

The research results play a certain role in understanding the ultra-high cycle fatigue behavior of additive manufacturing aluminum alloys. It can provide reference for improving the process parameters of SLM technology.

The purpose of this study is to campare the corrosion behavior of Az91 films and bulk sample, in the objective to provide reference for the corrosion resistance improvement of Mg alloys.

AZ91 films with various thickness values are produced by magnetron sputtering technique, and the corrosion behavior was characterized by immersion tests and electrochemical measurements.

The AZ91 films exhibited a preferred orientation with basal planes parallel to the surface and increased densification with the increase of thickness, and a superior corrosion resistance for the AZ91 films compared with the bulk sample.

The preferred (0002) basal planes in AZ91 films benefited the corrosion resistance and the nanoscale AZ91 films facilitated the development of a dense passivation film. Consequently, AZ91 film exhibited a superior corrosion resistance.

To solve the problems caused by using precise molds for copper column positioning in the current column grid array package, this paper aims to optimize the proposed friction plunge micro-welding (FPMW) technology without mold assistance, to overcome the problems of low interfacial bonding strength, shrinkage cavities and flash defects caused by the low hold-tight force of solder on the copper column.

A pressurizing device installed under the drill chuck of the friction welding machine is designed, which is used to apply a static constraint to the solder ball obliquely downward to increase the hold-tight force of the peripheral solder on the copper column during welding and promote the friction metallurgical connection between them.

The results show that the application of static constraint during welding can increase the compactness of the solder near the friction interface and effectively inhibit occurrences of flash, shrinkage cavities and crystal defects such as vacancies. Therefore, compared with the unconstrained (UC) FPMW, the average strength of the statically constrained (SC) FPMW joints and aged SC-FPMW joints can be increased by 51.1% and 122.6%, and the problem of the excessive growth of the interfacial connection layer in the UC-FPMW joints during aging can be effectively avoided.

The application of static constraint effectively inhibits the occurrence of defects such as shrinkage cavities, vacancies and flash in FPMW joints, and the welding quality is significantly improved.

This paper aims to systematically study the effects of reflow temperature and SAC0307 (SAC) content on the micromorphology and mechanical properties of Sn58Bi-xSAC0307 composite solder joints to meet the requirements of high integration and low-temperature packaging of devices and provide references for the application of composite solder joints.

Sn58Bi and SAC0307 solder paste was mechanically mixed in different proportions to prepare Sn58Bi-xSAC0307/ENIG solder joints. The thermal properties, microstructure and mechanical properties of the composite solder joints were studied.

As SAC content in the solder increases, the balling temperature of SnBi-SAC solder gradually increases. The addition of SAC alloy reduces the grain size of large Bi-rich phase, and there are small-sized dispersed Bi and Ag3Sn particles in the bulk solder. The intermetallic compounds composition of the SnBi-xSAC/ENIG solder joint changes from Ni3Sn4 to (Ni, Cu)3Sn4 and (Cu, Ni)6Sn5 with SAC increasing. As the soldering temperature increases, the strength of all solder joints shows a rising trend. Among them, the shear strength of SnBi-20SAC solder joints at a reflow temperature of 150°C is approximately 37 MPa. As the reflow temperature increases to 250°C, the shear strength of solder joints increases to approximately 67 MPa.

This study provides a reference for the optimization of low-temperature solder composition and soldering process under different package designs.

This paper aims to present spot pattern welding (SPW) as a scanning strategy for laser-foil-printing (LFP) additive manufacturing (AM) in place of the previously used continuous pattern welding (CPW) (line-raster scanning). The SPW strategy involves generating a sequence of overlapping spot welds on the metal foil, allowing the laser to form dense and uniform weld beads. This in turn reduces thermal gradients, promotes material consolidation and helps mitigate process-related risks such as thermal cracking, porosity, keyholing and Marangoni effects.

304L stainless steel (SS) feedstock is used to fabricate test specimens using the LFP system. Imaging techniques are used to examine the melt pool dimensions and layer bonding. In addition, the parts are evaluated for residual stresses, mechanical strength and grain size.

Compared to CPW, SPW provides a more reliable heating/cooling relationship that is less dependent on part geometry. The overlapping spot welds distribute heat more evenly, minimizing the risk of elevated temperatures during the AM process. In addition, the resulting dense and uniform weld beads contribute to lower residual stresses in the printed part.

To the best of the authors’ knowledge, this is the first study to thoroughly investigate SPW as a scanning strategy using the LFP process. In general, SPW presents a promising strategy for securing embedded sensors into LFP parts while minimizing residual stresses.