Search results

The impact of the application of hollow structures through variations of infill patterns and their density on the tensile properties was considered. The mechanical properties of the parts have a significant influence on the behavior and reliability of the parts in exploitation.

In this paper, the mechanical properties of the additively manufactured ABS material were investigated depending on the FDM printing parameters, which relate both to process parameters such as printing velocity and layer thickness, but also to coupled influence with the change of specimen orientation, that is raster angle. A standard tensile test was applied so that the specimens were prepared according to the ASTM D638 standard.

The results of the conducted experimental research enable the identification of the optimal choice of printing parameters for additively produced ABS materials with the highest values of strain at break and tensile strength. The significance of the obtained results is reflected in the recommendations for the selection of appropriate combination of process parameters for additive manufacturing of ABS parts using FDM technology.

This paper evaluates influence of FDM printing parameters on the tensile strength of parts and therefore on the reliability of the parts.

The purpose of this paper is to present an optimisation of four-point star-shaped structures produced through additive manufacturing (AM) polylactic acid (PLA). The study also aims to investigate the compression failure mechanism of the structure.

A Taguchi L₉ orthogonal array design of the experiment is adopted in which the input parameters are resolution (0.06, 0.15 and 0.30 mm), print speed (60, 70 and 80 mm/s) and bed temperature (55°C, 60°C, 65°C). The response parameters considered were printing time, material usage, compression yield strength, compression modulus and dimensional stability. Empirical observations during compression tests were used to evaluate the load–response mechanism of the structures.

The printing resolution is the most significant input parameter. Material length is not influenced by the printing speed and bed temperature. The compression stress–strain curve exhibits elastic, plateau and densification regions. All the samples exhibit negative Poisson’s ratio values within the elastic and plateau regions. At the beginning of densification, the Poisson’s ratios change to positive values. The metamaterial printed at a resolution of 0.3 mm, 80 mm/s and 60°C exhibits the best mechanical properties (yield strength and modulus of 2.02 and 58.87 MPa, respectively). The failure of the structure occurs through bending and torsion of the unit cells.

The optimisation study is significant for decision-making during the 3D printing and the empirical failure model shall complement the existing techniques for the mechanical analysis of the metamaterials.

To the best of the authors’ knowledge, for the first time, a new empirical model, based on the uniaxial load response and “static truss concept”, for failure mechanisms of the unit cell is presented.

The purpose of this paper is to review cases of artificial reefs built through additive manufacturing (AM) technologies and analyse their ecological goals, fabrication process, materials, structural design features and implementation location to determine predominant parameters, environmental impacts, advantages, and limitations.

The review analysed 16 cases of artificial reefs from both temperate and tropical regions. These were categorised based on the AM process used, the mortar material used (crucial for biological applications), the structural design features and the location of implementation. These parameters are assessed to determine how effectively the designs meet the stipulated ecological goals, how AM technologies demonstrate their potential in comparison to conventional methods and the preference locations of these implementations.

The overview revealed that the dominant artificial reef implementation occurs in the Mediterranean and Atlantic Seas, both accounting for 24%. The remaining cases were in the Australian Sea (20%), the South Asia Sea (12%), the Persian Gulf and the Pacific Ocean, both with 8%, and the Indian Sea with 4% of all the cases studied. It was concluded that fused filament fabrication, binder jetting and material extrusion represent the main AM processes used to build artificial reefs. Cementitious materials, ceramics, polymers and geopolymer formulations were used, incorporating aggregates from mineral residues, biological wastes and pozzolan materials, to reduce environmental impacts, promote the circular economy and be more beneficial for marine ecosystems. The evaluation ranking assessed how well their design and materials align with their ecological goals, demonstrating that five cases were ranked with high effectiveness, ten projects with moderate effectiveness and one case with low effectiveness.

AM represents an innovative method for marine restoration and management. It offers a rapid prototyping technique for design validation and enables the creation of highly complex shapes for habitat diversification while incorporating a diverse range of materials to benefit environmental and marine species’ habitats.

The paper's goal is to examine and illustrate the useful uses of submodeling in finite element modeling for topology optimization and stress analysis. The goal of the study is to demonstrate how submodeling – more especially, a 1D approach – can reliably and effectively produce ideal solutions for challenging structural issues. The paper aims to demonstrate the usefulness of submodeling in obtaining converged solutions for stress analysis and optimized geometry for improved fatigue life by studying a cantilever beam case and using beam formulations. In order to guarantee the precision and dependability of the optimization process, the developed approach will also be validated through experimental testing, such as 3-point bending tests and 3D printing. Using 3D finite element models, the 1D submodeling approach is further validated in the final step, showing a strong correlation with experimental data for deflection calculations.

The authors conducted a literature review to understand the existing research on submodeling and its practical applications in finite element modeling. They selected a cantilever beam case as a test subject to demonstrate stress analysis and topology optimization through submodeling. They developed a 1D submodeling approach to streamline the optimization process and ensure result validity. The authors utilized beam formulations to optimize and validate the outcomes of the submodeling approach. They 3D-printed the optimized models and subjected them to a 3-point bending test to confirm the accuracy of the developed approach. They employed 3D finite element models for submodeling to validate the 1D approach, focusing on specific finite elements for deflection calculations and analyzed the results to demonstrate a strong correlation between the theoretical models and experimental data, showcasing the effectiveness of the submodeling methodology in achieving optimal solutions efficiently and accurately.

The findings of the paper are as follows: 1. The use of submodeling, specifically a 1D submodeling approach, proved to be effective in achieving optimal solutions more efficiently and accurately in finite element modeling. 2. The study conducted on a cantilever beam case demonstrated successful stress analysis and topology optimization through submodeling, resulting in optimized geometry for enhanced fatigue life. 3. Beam formulations were utilized to optimize and validate the outcomes of the submodeling approach, leading to the successful 3D printing and testing of the optimized models through a 3-point bending test. 4. Experimental results confirmed the accuracy and validity of the developed submodeling approach in streamlining the optimization process. 5. The use of 3D finite element models for submodeling further validated the 1D approach, with specific finite elements showing a strong correlation with experimental data in deflection calculations. Overall, the findings highlight the effectiveness of submodeling techniques in achieving optimal solutions and validating results in finite element modeling, stress analysis and optimization processes.

The originality and value of the paper lie in its innovative approach to utilizing submodeling techniques in finite element modeling for structural analysis and optimization. By focusing on the reduction of finite element models and the creation of smaller, more manageable models through submodeling, the paper offers designers a more efficient and accurate way to achieve optimal solutions for complex problems. The study's use of a cantilever beam case to demonstrate stress analysis and topology optimization showcases the practical applications of submodeling in real-world scenarios. The development of a 1D submodeling approach, along with the utilization of beam formulations and 3D printing for experimental validation, adds a novel dimension to the research. Furthermore, the paper's integration of 1D and 3D submodeling techniques for deflection calculations and validation highlights the thoroughness and rigor of the study. The strong correlation between the finite element models and experimental data underscores the reliability and accuracy of the developed approach. Overall, the originality and value of this paper lie in its comprehensive exploration of submodeling techniques, its practical applications in structural analysis and optimization and its successful validation through experimental testing.

This empirical study aims to investigate the erosion wear performance of two different 3D-printed materials (acrylonitrile butadiene styrene [ABS] and polylactic acid [PLA]) with various micro textures. The two different textures (prism and square) were created over the surfaces of both materials by using the 3D-printed technique.

The erosion experiments on both materials were performed by using Ducom Erosion Jet Tester. Erosion tests were performed at four different impacting velocities (15, 30, 45 and 60 m/s) with the four different particle sizes (17, 39, 63 97 µm) at the impact angles (30°–90°) for the time duration of 5, 10, 15 and 20 min. The two different textures prism and cone were used for performing the erosion experiments. Taguchi’s orthogonal L16 (mixed level) was used to reduce the number of experiments and to determine the impact of these parameters on erosion wear performance of both 3D-printed materials.

The PLA with cone texture was found to be best (against erosion) than the ABS cone and prism textures due to their high hardness (68 HV). Also, the average signal to noise (S/N) ratio for PLA and ABS was measured as 56.4 and 44.4 dB, respectively. As the value of the S/N ratio is inversely proportional to the erosion rate, the PLA has the least erosion rate as compared to the ABS. The sequence of erosion wear influencing parameters for both materials was in the following order: velocity > erodent size > texture > impact angle > time interval.

Both PLA and ABS with different micro textures for erosion testing were studied with Taguchi’s optimization method, and the erosion mechanisms are well analyzed by using scanning electron microscopy and Image J techniques.

This study aims to evaluate in situ oxidative polymerization of aniline (Ani) as a post-processing method to promote extrusion-based 3D printed parts, made from insulating polymers, to components with functional properties, including electrical conductivity and chemical sensitivity.

Extrusion-based 3D printed parts of polyethylene terephthalate modified with glycol (PETG) and polypropylene (PP) were coated in an aqueous acid solution via in situ oxidative polymerization of Ani. First, the feedstocks were characterized. Densely printed samples were then used to assess the adhesion of polyaniline (PAni) and electrical conductivity on printed parts. The best feedstock candidate for PAni coating was selected for further analysis. Last, a Taguchi methodology was used to evaluate the influence of printing parameters on the coating of porous samples. Analysis of variance and Tukey post hoc test were used to identify the best levels for each parameter.

Colorimetry measurements showed significant color shifts in PP samples and no shifts in PETG samples upon pullout testing. The incorporation of PAni content and electrical conductivity were, respectively, 41% and 571% higher for PETG in comparison to PP. Upon coating, the surface energy of both materials decreased. Additionally, the dynamic mechanical analysis test showed minimal influence of PAni over the dynamic mechanical properties of PETG. The parametric study indicated that only layer thickness and infill pattern had a significant influence on PAni incorporation and electrical conductivity of coated porous samples.

Current literature reports difficulties in incorporating PAni without affecting dimensional precision and feedstock stability. In situ, oxidative polymerization of Ani could overcome these limitations. However, its use as a functional post-processing of extrusion-based printed parts is a novelty.

Material extrusion (MEX) is one of the most known techniques in the additive manufacturing (AM) sector to produce components with a wide range of polymeric and composite materials. Moisture causes alterations in material properties and for filaments strongly hygroscopic like nylon-based composites this means greater ease of deterioration. Drying the filament to reduce the moisture content may not be sufficient if the humidity is not controlled during printing. The purpose of this study is to achieve the recovery of a commercial nylon-based composite filament by applying process optimization using an open source MEX machine.

A statistical approach based on Taguchi’s method allowed to achieve an ultimate tensile strength (UTS). A verification of the geometrical capabilities of the process has been performed according to the standard ISO/ASTM 52902-2019. Chemical tests were also carried out to test the resistance to corrosion in acid and basic solutions.

An UTS of 71.37 MPa was obtained, significantly higher than the value declared by the filament’s manufacturer (Stratasys Inc., USA). The best configuration of process parameters leads to good geometrical deviations for flat surfaces, in a range of 0.01 and 0.38 for flatness, while cylindrical faces showed more important deviations from the nominal values. The good applicability of the material in corrosive environments has been confirmed.

This study examined the performance restoration potential of a nylon composite filament that was significantly affected by storage conditions. For the filament manufacturer, if the material remains in ambient air for an hour or idle in the machine for more than 24 h, the material may no longer be suitable for printing. The study highlighted that the drying of the filament must not be temporary but constant to guarantee printability, and, by acting on the process parameters, it is possible to obtain better mechanical properties than declared by the manufacturer.

This study aims to improve the mechanical properties of an object produced by fused deposition modelling with high-grade polymer.

The study uses an ensembled surrogate-assisted evolutionary algorithm (SAEA) to optimize the process parameters for example, layer height, print speed, print direction and nozzle temperature for enhancing the mechanical properties of temperature-sensitive high-grade polymer poly-ether-ether-ketone (PEEK) in fused deposition modelling (FDM) 3D printing while considering print time as one of the important parameter. These models are integrated with an evolutionary algorithm to efficiently explore parameter space. The optimized parameters from the SAEA approach are compared with those obtained using the Gray Relational Analysis (GRA) Taguchi method serving as a benchmark. Later, the study also highlights the significant role of print direction in optimizing the mechanical properties of FDM 3D printed PEEK.

With the use of ensemble learning-based SAEA, one can successfully maximize the ultimate stress and percentage elongation with minimum print time. SAEA-based solution has 28.86% higher ultimate stress, 66.95% lower percentage of elongation and 7.14% lower print time in comparison to the benchmark result (GRA Taguchi method). Also, the results from the experimental investigation indicate that the print direction has a greater role in deciding the optimum value of mechanical properties for FDM 3D printed high-grade thermoplastic PEEK polymer.

This study is valid for the parameter ranges, which are defined to conduct the experimentation.

This study has been conducted on the basis of taking only a few important process parameters as per the literatures and available scope of the study; however, there are many other parameters, e.g. wall thickness, road width, print orientation, fill pattern, roller speed, retraction, etc. which can be included to make a more comprehensive investigation and accuracy of the results for practical implementation.

This study deploys a novel meta-model-based optimization approach for enhancing the mechanical properties of high-grade thermoplastic polymers, which is rarely available in the published literature in the research domain.

This paper aims to provide a reference for the development of digital transformation from the perspective of manufacturing process links.

This paper applies canonical correlation analysis based on digital technology patents in the key links of manufacturing industries (product design, procurement, product manufacturing, warehousing and transportation, and wholesale and retail) and the related indicators of economic benefits of regions in China.

(1) The degree of digitalization of manufacturing process links is significantly correlated with economic benefits. (2) The improvement of the degree of digitalization in the “product design” link, the “warehousing and transportation” link, the “product manufacturing” link and the “wholesale and retail” link has significant impacts on the economic benefits of manufacturing industry. (3) The digital degree of the “procurement” link has no obvious influence on the economic benefits of manufacturing industry.

The research results can provide reference for the formulation and implementation of micro policies. The strategy of improving the level of digital transformation of key links of manufacturing industry is put forward to better promote both the digital transformation of manufacturing industry and economic development.

This paper innovatively studies the relationship between digitalization of manufacturing process links and economic benefits. The findings can provide theoretical and empirical support for the digital transformation of China's manufacturing industry and high-quality development of economy.

The current analysis was conducted to investigate the quality of surfaces and geometry of tracks printed using PolyMideTM CoPA, PolymaxTM PC and PolyMideTM PA6-CF materials through fused deposition modelling (FDM). This study also examined the degree of fusion of adjacent filaments (tracks) to approximate the optimal process parameters of the three materials.

Images of fused adjacent filaments were acquired using scanning electron microscopy (SEM), after which, they were analysed using Image J Software and Minitab Software to determine the optimal process parameters.

The optimal process parameters for PolyMideTM CoPA are 0.25 mm, 40 mm/s, −0.10 mm, 255°C and 0.50 mm for layer thickness, printing speed, hatch spacing, extrusion temperature and extrusion width, respectively. It was also concluded that the optimal process parameters for PolymaxTM PC are 0.30 mm, 40 mm/s, 0.00 mm, 260°C and 0.6 mm for layer thickness, printing speed, hatch spacing, extrusion temperature and extrusion width, respectively.

It was difficult to separate tracks printed using PolyMideTM PA6-CF from the support structure, making it impossible to examine and determine their degree of fusion using SEM.

The study provides more knowledge on FDM, which is one of the leading additive manufacturing technology for polymers. The information provided in this study helps in continued uptake of the technique, which can help create job opportunities, especially among the youth and young engineers.

This study proposes a new and a more accurate method for optimising process parameters of FDM at meso-scale level.