Search results

Adhesive bonding is critical to the effectiveness and structural integrity of 3D printed components. The purpose of this study is to investigate the effect of joint configuration on failure loads to improve the design and performance of single lap joints (SLJs) in 3D printed parts.

In this study, adherends were fabricated using material extrusion 3D printing technology with polyethylene terephthalate glycol (PETG). A toughened methacrylate adhesive was chosen to bond the SLJs after adherend printing. In this study, response surface methodology (RSM) was used to examine the effect of the independent variables of failure load, manufacturing time and mass on the dependent variable of joint configuration; adherend thickness (3.2, 4.0, 4.8, 5.6, 6.4, and 7.2 mm) and overlap lengths (12.7, 25.4, 38.1, and 50.8 mm) of 3D printed PETG SLJs.

The strength of the joints improved significantly with the increase in overlap length and adherend thickness, although the relationship was not linear. The maximum failure load occurred with a thickness of 7.2 mm and an overlap of 50.8 mm, whilst the minimum failure load was determined with a thickness of 3.2 mm and an overlap of 12.7 mm. The RSM findings show that the optimum failure load was achieved with an adherend thickness of 3.6 mm and an overlap length of 37.9 mm for SLJ.

This study provides insight into the optimum failure load for 3D printed SLJs, reducing SLJ production time and mass, producing lightweight structures due to the nature of 3D printing, and increasing the use of these parts in load-bearing applications.

Adhesively bonded joints are used in many fields, especially in the automotive, marine, aviation, defense and outdoor industries. Adhesive bonding offers advantages over traditional mechanical methods, including the ability to join diverse materials, even load distribution and efficient thermal-electrical insulation. This study aims to investigate the mechanical properties of adhesively bonded joints, focusing on adherends produced with auxetic and flat surfaces adhered with varying adhesive thicknesses.

The research uses three-dimensional (3D)-printed materials, polyethylene terephthalate glycol and polylactic acid, and two adhesive types with ductile and brittle properties for single lap joints, analyzing their mechanical performance through tensile testing. The adhesion region of one of these adherends was formed with a flat surface and the other with an auxetic surface. Adhesively bonded joints were produced with 0.2, 0.3 and 0.4 mm bonding thickness.

Results reveal that auxetic adherends exhibit higher strength compared to flat surfaces. Interestingly, the strength of ductile adhesives in auxetic bonded joints increases with adhesive thickness, while brittle adhesive strength decreases with thicker auxetic bonds. Moreover, the auxetic structure displays reduced elongation under comparable force.

The findings emphasize the intricate interplay between adhesive type, bonded surface configuration of adherend and bonding thickness, crucial for understanding the mechanical behavior of adhesively bonded joints in the context of 3D-printed materials.

This study aims to examine the impact of specific printing factors, such as layer height, line width and build orientation, on the overall quality of fused filament fabrication (FFF) 3D printed structures. The project also intends to use response surface methodology (RSM) to maximize ultimate tensile strength (UTS) while lowering surface roughness and printing time.

This study used an FFF printer to fabricate samples of polylactic acid (PLA), which were then subjected to assessments of tensile strength and surface roughness. A tensile test was conducted under standardized conditions according to the ASTM D638 standard test method using the AG-50 kN Shimadzu Autograph. The Mitutoyo Surftest SJ-210, which utilizes a needle-tipped inductive method, was used to determine surface roughness. RSM was used for optimization.

This work provides useful insights into how the printing parameters affect FFF 3D printed structures, which may be used to optimize the printing process and improve PLA-based 3D printed products' qualities. The determined optimal values for building orientation, layer height and line width were 0°, 0.1 mm and 0.6 mm, respectively. The total desirability value of 0.80 implies desirable outcomes, and good agreement between experimental and projected response values supports the suggested models.

Previous RSM studies for 3D printing parameter optimization focused on mechanical properties or surface aspects, however, few examined multiple responses and their interactions. This study emphasizes the relevance of FFF parameters like line width, which are often overlooked but can dramatically impact printing quality. Mechanical properties, surface quality and printing time are integrated to comprehend optimization holistically.

The purpose of this paper is to evaluate and exploit the combination of additive manufacturing polymeric technology and structural adhesives. The main advantage is to expand the maximum dimension of the 3D printed parts, which is typically limited, by joining the parts with structural adhesive, without losing strength and stiffness and keeping the major asset of polymeric 3 D printing: freedom of shape of the system and low cost of parts.

The materials used in the paper are the following. The adhesive considered is a commercial inexpensive acrylic, quite similar to superglue, applicable with almost no surface preparation and fast curing, as time constraint is one of the key problems that affects industrial adhesive applications. The 3D printed parts were in acrylonitrile butadiene styrene (ABS), obtained with a Fortus 250mc FDM machine, from Stratasys. The work first compares flat overlap joint with joints designed to permit mechanical interlocking of the adherends and then to a monolithic component with the same geometry. Single lap, joggle lap and double lap joints are the configurations experimentally characterized following a design of experiment approach.

The results show a failure in the substrate, due to the low strength of the polymeric adherends for the first batch of typical bonded configurations, single lap, joggle lap and double lap. The central bonded area, with an increased global thickness, never does fail, and the adhesive is able to transfer the load both with and without mechanical interlocking. An additional set of scarf joints was also tested to promote adhesive failure as well as to retrieve the adhesive strength in this application. The results shows that bonding of polymeric AM parts is able to express its full potential compared with a monolithic solution even though the joint fails prematurely in the adherend due to the bending stresses and the notches present in the lap joints.

Because of the 3D printed polymeric material adopted, the results may be generalized only when the elastic properties of the adherends and of the adhesive are similar, so it is not possible to extend the findings of the work to metallic additive manufactured components.

The paper shows that the adhesives are feasible way to expand the potentiality of 3 D printed equipment to obtain larger parts with equivalent mechanical properties. The paper also shows that the scarf joint, which fails in the adhesive first, can be used to extract information about the adhesive strength, useful for the designers which have to combine adhesive and additive manufactured polymeric parts.

To the best of the researchers’ knowledge, there are scarce quantitative information in technical literature about the performance of additive manufactured parts in combination with structural adhesives and this work provides an insight on this interesting subject. This manuscript provides a feasible way of using rapid prototyping techniques in combination with adhesive bonding to fully exploit the additive manufacturing capability and to create large and cost-effective 3 D printed parts.

Acrylonitrile butadiene styrene (ABS), as a light and high strength thermoplastic polymer, has found extensive applications in different industries. Fused filament fabrication, known as three-dimensional (3D) printing technique is considered a rapid prototyping technique that is frequently applied for production of samples of ABS material. Therefore, the purpose of this study is to investigate the mechanical and fracture behavior of such materials and the techniques to improve such properties.

Experimental and numerical analyses have been conducted to investigate the effects of internal architecture and chopped carbon fiber (CF) fillers on the mechanical properties and mixed mode fracture behavior of the ABS samples made by 3D printing technique. Four different filling types at 70% filling ratios have been used to produce tensile and special fracture test samples with pure and CF filled ABS filaments (CF-ABS) using 3D process. A special fixture has been developed to apply mixed mode loading on fracture samples, and finite element analyses have been conducted to determine the geometric function of such samples at different loading angles.

It has been determined that the printing pattern has a significant effect on the mechanical properties of the sample. The addition of 15% CF to pure ABS resulted in a significant increase in tensile strength of 46.02% for line filling type and 15.04% for hexagon filling type. It has been determined that as the loading angle increases from 0° to 90°, the KIC value decreases. The addition of 15% CF increased the K_IC values for hexagonal and line filling type by 64.14% and 12.5%, respectively.

The damage that will occur in ABS samples produced in 3D printers depends on the type, amount, filling speed, filling type, filling ratio, filling direction and mechanical properties of the additives. All these features are clearly dependent on the production method. Even if the same additive is used, the production method difference shows different microstructural parameters, especially different mechanical properties.

This study aims to comprehensively investigate the mixed-mode fracture behavior and mechanical properties of selective laser sintering (SLS) polyamide 12 (PA12) components, considering different build orientations and layer thicknesses. The primary objectives include the following. Conducting mixed-mode fracture and mechanical analyses on SLS PA12 parts. Investigating the influence of build orientation and layer thickness on the mechanical properties of SLS-printed components. Examining the fracture mechanisms of SLS-produced Arcan fracture and tensile specimens through experimental methods and finite element analyses.

The research used a combination of experimental techniques and numerical analyses. Tensile and Arcan fracture specimens were fabricated using the SLS process with varying build orientations (X, X–Y, Z) and layer thicknesses (0.1 mm, 0.2 mm). Mechanical properties, including tensile strength, modulus of elasticity and critical stress intensity factor, were quantified through experimental testing. Mixed-mode fracture tests were conducted using a specialized fixture, and finite element analyses using the J-integral method were performed to calculate fracture toughness. Scanning electron microscopy (SEM) was used for detailed morphological analysis of fractured surfaces.

The investigation revealed that the highest tensile properties were achieved in samples fabricated horizontally in the X orientation with a layer thickness of 0.1 mm. Additionally, parts manufactured with a layer thickness of 0.2 mm exhibited favorable mixed-mode fracture behavior. The results emphasize the significance of build orientation and layer thickness in influencing mechanical properties and fracture behavior. SEM analysis provided valuable insights into the failure mechanisms of SLS-produced PA12 components.

This study contributes to the field of additive manufacturing by providing a comprehensive analysis of the mixed-mode fracture behavior and mechanical properties of SLS-produced PA12 components. The investigation offers novel insights into the influence of build orientation and layer thickness on the performance of such components. The combination of experimental testing, numerical analyses and SEM morphological observations enhances the understanding of fracture behavior in additive manufacturing processes. The findings contribute to optimizing the design and manufacturing of high-quality PA12 components using SLS technology.

The extension of the vacuum-assisted multipoint moulding (VAMM) technology to a broader field of geometries makes it necessary to extend it with attachments to the enhanced vacuum-assisted multipoint moulding with additive attachments (EMMA) technology. Therefore, it is necessary to build additive manufactured attachments on a curved silicone surface by fused filament fabrication (FFF). The main challenge of FFF on a silicone-made build plate is the adhesion of the part on the build plate. Hence, the purpose of this paper is to find suitable and reliably manufacturable material and adhesion promoter combinations for the use of the FFF on silicone build plates.

The combinations of seven different filaments and four adhesion promoters were investigated with an experimental study. Therefore, four different specimen geometries were built with the different combinations and tested in a tensile test, and some of the specimens were analysed with a confocal laser scanning microscope (CLSM).

This study proves that the FFF on unheated silicone building plates is possible for several material combinations. As a filament material, polylactide can reliably be manufactured with all of the investigated adhesion promoters on the silicone build plate. Thereby, the highest adhesion strengths were achieved with an adhesive foil as an adhesion promoter, whereas the glue stick is the most appropriate solution. The investigations with the CLSM showed that there are large differences in the manifestation of the first layer depending on the adhesion promoter used.

To the best of the authors’ knowledge, this study is the first to demonstrate the manufacturing of FFF-made attachments on silicone build plates for the EMMA process. This paper provides measurement data on the build plate adhesion of the attachments on silicone-made build plates.

Additive manufacturing has disadvantages, such as the maximum part size being limited by the machine’s working volume. Therefore, if a part more considerable than the working volume is required, the part is produced in parts and joined together. Among the many methods of joining thermoplastic parts, adhesives and mechanical interlocking are considered. This study aims to characterize and optimize mechanically stressed adhesive joints combined with female and male mechanical interlocking on acrylonitrile butadiene styrene (ABS) specimens made with fused filament fabrication (FFF) so that the joint strength is as close as possible to the strength of the base material.

This study characterized the subject’s state of the art to justify the decisions regarding the experimental design planned in this research. Subsequently, this study designed, executed and analyzed the experiment using a statistical analysis of variance. The output variables were yield strength and tensile strength. The input variables were two different cyanoacrylate adhesives, two different types of mechanical interlock (truncated pyramid and cylindrical pin) and the dimensions of each type of mechanical interlock. This study used simple and factorial experiments to select the best adhesive and interlocking to be optimized using the response surface and the steep ascent method.

The two adhesives have no statistical difference, but they show different data dispersion. The design or yield stress was a determining factor for selecting the optimal specimen, with cylindrical geometry exhibiting higher resistance at initial failure. Geometry type is crucial due to the presence of stress concentrators. The cylindrical geometry with fewer stress concentrators demonstrated better tensile strength. Ultimately, the specimen with a mechanically reinforced joint featuring a cylindrical pin of radius 5.45 mm and height of 4.6 mm exhibited the maximum tensile and yield strength.

Previous research suggests that a research opportunity is the combination of bonding methods in FFF or fused deposition modeling, which is not a frequent topic, and this research to enrich that topic combines the adhesive with mechanically interlocked joints and studies it experimentally for FFF materials, to provide unpublished information of the performance of the adhesive joint with mechanical interlocking, to designers and manufacturers of this technology.