Search results

This paper aims to study the tribological characteristics of the electrical contact system under different displacement amplitudes.

First, the risk frequency of real nuclear safety distributed control system (DCS) equipment is evaluated. Subsequently, a reciprocating friction test device which is characterized by a ball-on-flat configuration is established, and a series of current-carrying tribological tests are carried out at this risk frequency.

At risk frequency and larger displacement amplitude, the friction coefficient visibly rises. The reliability of the electrical contact system declines as amplitude increases. The wear morphology analysis shows that the wear rate increases significantly and the degree of interface wear intensifies at a larger amplitude. The wear area occupied by the third body layer increases sharply, and the appearance of plateaus on the surface leads to the increase of friction coefficient and contact resistance. EDS analysis suggests that oxygen elements progressively arise in the third layer as a result of increased air exposure brought on by larger displacement amplitude.

Results are significant for recognizing the tribological properties of electrical connectors in nuclear power control systems.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-03-2024-0098/

The purpose of this paper is to investigate the friction and wear mechanisms in lubricated sliding conditions of additively manufactured SS316L parts. The different viscous oils 5W30, 15W40, 20W50 and SAE140 are used. These investigations provide a theoretical basis for the high performance of printed and postheattreated SS316L.

Tribological tests were carried out on selective laser melting-made SS316L printed specimens and heat-treated specimens. The parameters in 15 min of test duration are 20 N of load, 200 rpm, 8 mm of pin diameter, 25 mm length, 80 mm of track diameter and EN31 counter disc body. This work presented the phenomena of lubrication regimes and their characterization, as identified by the Stribeck curve, and these regimes affect the tribological properties of additively manufactured SS316L under the influence of industrial viscous lubricants. The results are observed using Scanning electron microscope (SEM), X-ray diffraction (XRD) and wear tests.

The observations indicate that additively manufactured SS316L shows a reduced coefficient of friction (COF) and specific wear rate (SWR). This is credited to the utilization of different viscous lubricants.

This exclusive research demonstrates how various viscous lubricants affect the COF and SWR of printed and post-heat-treated SS316L parts. Lambda (λ), lubricant film thickness (h₀), surface roughness and wear mechanisms are studied and reported.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-04-2024-0110/

The nickel-based alloys Inconel 625 and Inconel 718 stand out due to their high strength and corrosion resistance in important industries like aerospace, aviation and automotive. Even though they are widely used, current techniques of producing materials that are difficult to cut pose several problems from a financial, ecological and even health perspective. To handle these problems and acquire improved mechanical and structural qualities, laser powder bed fusion (LPBF) has been widely used as one of the most essential additive manufacturing techniques. The purpose of this article is to focus on the state of the art on LPBF parts of Inconel 625 and Inconel 718 for microstructure, mechanical behavior and postprocessing.

The mechanical behavior of LPBF-fabricated Inconel is described, including hardness, surface morphology and wear, as well as the influence of fabrication orientation on surface quality, biocompatibility and resultant mechanical properties, particularly tensile strength, fatigue performance and tribological behaviors.

The postprocessing techniques such as thermal treatments, polishing techniques for surface enhancement, mechanical and laser-induced peening and physical operations are summarized.

The highlighted topic presents the critical aspects of the advantages and challenges of the LPBF parts produced by Inconel 718 and 625, which can be a guideline for manufacturers and academia in practical applications.

The purpose of this paper is to investigate the effect of laser peening (LP) on mechanical and wear properties of 304 stainless steel sheet.

Three-dimensional morphology, micro-hardness and micro-structure of shocked samples were tested. The wear amount, wear track morphology and wear mechanism were also characterized under dry sliding wear using Al₂O₃ ceramics ball.

The LP treatment generates deformation twins that contribute to the grain refinement and hardness increase. The wear test displays that the wear mechanism of samples is mainly abrasive wear and oxidation wear at 10 N load. While at 30 N, the delamination and adhesion areas of treated sample are reduced visibly compared to untreated ones.

This study specifically investigates the mechanical and wear properties of 304 stainless steel after the direct action of LP on its surface, which shows an effective improvement on the wear resistance. For example, the wear loss of processed sample is reduced by 19% at 30 N, the friction coefficient decreases from 0.4714 to 0.4308 and the groove depth is reduced from 78.1 to 74.4 µm under same condition.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-01-2024-0007/

This study aims to study the formation mechanism of micro-arc oxidation (MAO) coating on AZ31 magnesium alloy and how the annealing process affects its corrosion resistance.

This study involved immersion experiments, electrochemical experiments and slow strain rate tensile experiments, along with scanning electron microscopy, optical microscopy observation and X-ray diffraction analysis.

The findings suggest that annealing treatment can refine the grain size of AZ31 magnesium alloy to an average of 6.9 µm at 300°C. The change in grain size leads to a change in conductivity, which affects the performance of MAO coatings. The MAO coating obtained by annealing the substrate at 300°C has smaller pores and porosity, resulting in better adhesion and wear resistance.

The coating acts as a barrier to prevent corrosive substances from entering the substrate. However, the smaller pores and porosity reduce the channels for the corrosive solution to pass through the coating. When the coating cracks or falls off, the corrosive medium and substrate come into direct contact. Smaller and uniform grains have better corrosion resistance.

The purpose of this study is to design and process the optimal V-shaped microstructure for 7075 aluminum alloy and reveal its wear resistance mechanism and performance.

The hydrodynamic pressure lubrication models of the nontextured, V-shaped, circular and square microtextures are established. The corresponding oil film pressure distributions are explored. The friction and wear experiments are conducted on a rotating device. The effects of the microstructure shapes and sizes on the wear mechanisms are investigated via the friction coefficients and surface morphologies.

In comparison, the V-shaped microtexture has the largest oil film carrying capacity and the lowest friction coefficient. The wear mechanism of the V-shaped microtexture is dominated by abrasive and adhesive wear. The V-shaped microtexture has excellent wear resistance under a side length of 300 µm, an interval of 300 µm and a depth of 20 µm.

This study is conductive to the design of wear-resistant surfaces for friction components.

The purpose of this paper is to improve the mechanical and tribological properties of Si₃N₄ ceramics and to make the application of Si₃N₄ ceramics as tribological materials more extensive.

Si₃N₄-based composite ceramics (SN-2L) containing nitrogen-doped graphene quantum dots (N-GQDs) were prepared by hot press sintering process through adding 2 Wt.% nanolignin as precursor to the Si₃N₄ matrix, and the dry friction and wear behaviors of Si₃N₄-based composite against TC4 disc were performed at the different loads by using pin-on-disc tester.

The friction coefficients and wear rates of SN-2L composite against TC4 were significantly lower than those of the single-phase Si₃N₄ against TC4 at the load range from 15 to 45 N. At higher load of 45 N, SN-2L/TC4 pair presented the lowest friction coefficient of 0.25, and the wear rates of the pins and discs were as low as 1.76 × 10⁻⁶ and 2.59 × 10⁻⁴mm³/N·m. The low friction and wear behavior could be attributed to the detachment of N-GQDs from the ceramic matrix to the worn surface at the load of 30 N or higher, and then an effective lubricating film containing N-GQDs, SiO₂, TiO₂ and Al₂SiO₅ formed in the worn surface. While, at the same test condition, the friction coefficient of the single-phase Si₃N₄ against TC4 was at a range from 0.45 to 0.58. The spalling and cracking morphology formed on the worn surface of single-phase Si3N4, and the wear mechanism was mainly dominated by adhesive and abrasive wear.

Overall, a high-performance green ceramic composite was prepared, and the composite had a good potential for application in engineering tribology fields (such as aerospace bearings).

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-05-2024-0161/

The purpose of this article is to prepare graphene/polyimide composite materials for use as bearing cage materials, improving the friction and wear performance of bearing cages.

The oil absorption and discharge tests were conducted to evaluate the oil content properties of the materials, while the mechanical properties were analyzed through cross-sectional morphology examination. Investigation into the tribological behavior and wear mechanisms encompassed characterization and analysis of wear trace morphology in PPI-based materials. Consequently, the influence of varied graphene nanoplatelets (GN) concentrations on the oil content, mechanical and tribological properties of PPI-based materials was elucidated.

The composites exhibit excellent oil-containing properties due to the increased porosity of PPI-GN composites. The robust formation of covalent bonds between GN and PPI amplifies the adhesive potency of the PPI-GN composites, thereby inducing a substantial enhancement in impact strength. Notably, the PPI-GN composites showed enhanced lubrication properties compared to PPI, which was particularly evident at a GN content of 0.5 Wt.%, as evidenced by the minimization of the average coefficient of friction and the width of the abrasion marks.

This paper includes implications for elucidating the wear mechanism of the polyimide composites under frictional wear conditions and then to guide the optimization of oil content and tribological properties of polyimide bearing cage materials.

In this paper, homogeneously dispersed PPI-GN composites were effectively synthesized by introducing GN into a polyimide matrix through in situ polymerization, and the lubrication mechanism of the PPI composites was compared with that of the PPI-GN composites to illustrate the composites’ superiority.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-12-2023-0415

The purpose of this paper is to investigate the effect of mullite on the mechanical properties and friction of carbon fiber (CF)-reinforced friction material.

CF-reinforced friction materials with varying content of mullite were fabricated by hot press molding, and then the tribological properties were tested on the MRH-3-type tribometer under ambient conditions with the ring-on-block configuration.

The experimental results indicated that the addition of mullite increased the density and compressive strength of friction material. However, the flexural strength of friction material decreased by 16% with the addition of 15 Wt.% mullite. The friction coefficient was proportional to the mullite content. Friction material with 12.5 Wt.% mullite showed the highest friction stability under different loads, whereas friction material with 10 Wt.% mullite exhibited the highest friction stability under different sliding speeds.

By boosting the resistance to deformation under load and increasing the specific heat capacity, mullite contributed significantly to the friction stability of the friction material.

Liquid-assisted laser surface texturing technology was used to create composite microtextures on triangular guide rail surfaces to enhance their tribological properties.

Numerical simulations were used to investigate the impact of various microtextures on fluid dynamic lubrication. Reciprocating friction and wear tests, followed by mechanistic analysis, examined the combined tribological effects of microtextured surfaces and lubricants.

The numerical simulation outcomes reveal a significant augmentation in the influence of fluid dynamic pressure due to composite microtextures, consequently amplifying the load-bearing capacity of the oil film. The average friction coefficient of composite microtextured samples was approximately 0.136 in reciprocating pin-on-disk friction tests, representing approximately 17% decrease compared to polished samples. Triangular guide rails with composite microtextures demonstrated the lowest average coefficient under conditions of high-speed and heavy-loading in the reciprocating friction and wear tests. Additionally, the presence of composite microtextures was found to promote the formation of adsorbed and friction films during friction, potentially contributing to the enhancement of tribological properties.

Triangular guide rails face high friction and wear, limiting their stability in demanding applications like machine tool guideways. This paper proposes a novel approach for steel triangular guide rails, involving composite microtexturing, numerical fluid simulations, liquid-assisted laser surface texturing and friction-wear testing. By implementing composite microtextures, the method aims to reduce friction coefficients and extend guideway service life, thereby saving energy and reducing maintenance costs. Enhancing the antifriction and antiwear properties of machine tool guideways is crucial for improving performance and longevity.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-05-2024-0183/