Search results

This paper aims to present a detailed investigation on the parameter estimation of a photovoltaic (PV) module by using a simplified two-diode model.

The studied PV module in this paper resembles an ideal two-diode model, and to reduce the computational time, the proposed model has a photocurrent source and two ideal-diodes and neglects the series and shunt resistances. Hence, for calculating the unknown parameters, only four parameters are required from the datasheet. Moreover, the studied model is simple and uses an easy modeling approach which is free from complexities.

The performance of the PV module is analyzed under non-standard test conditions by considering partial shading at different shaded levels, and it is found that the model has less computational time and gives accurate results.

The usefulness of this PV model is demonstrated with the help of several illustrative figures, and the performance of the PV module is evaluated.

Parameter identification of photovoltaic (PV) modules plays a vital role in modeling PV systems. This study aims to propose a novel hybrid approach to identify the seven parameters of the two-diode model of PV modules with high accuracy.

The proposed hybrid approach combines an improved particle swarm optimization (IPSO) algorithm with an analytical approach. Three parameters are optimized using IPSO, whereas the other four are analytically determined. To improve the performance of IPSO, three improvements are adopted, that is, evaluating the particles with two evaluation functions, adaptive evolutionary learning and adaptive mutation.

The performance of proposed approach is first verified by comparing with several well-established algorithms for two case studies. Then, the proposed method is applied to extract the seven parameters of CSUN340-72M under different operating conditions. The comprehensively experimental results and comparison with other methods verify the effectiveness and precision of the proposed method. Furthermore, the performance of IPSO is evaluated against that of several popular intelligent algorithms. The results indicate that IPSO obtains the best performance in terms of the accuracy and robustness.

An improved hybrid approach for parameter identification of the two-diode model of PV modules is proposed. The proposed approach considers the recombination saturation current of the p–n junction in the depletion region and makes no assumptions or ignores certain parameters, which results in higher precision. The proposed method can be applied to the modeling and simulation for research and development of PV systems.

Estimation of solar cell parameters, mathematical modeling and the actual performance analysis of photovoltaic (PV) cells at various ecological conditions are very important in the design and analysis of maximum power point trackers and power converters. This study aims to propose the analysis and modeling of a simplified three-diode model based on the manufacturer’s performance data.

A novel technique is presented to evaluate the PV cell constraints and simplify the existing equation using analytical and iterative methods. To examine the current equation, this study focuses on three crucial operational points: open circuit, short circuit and maximum operating points. The number of parameters needed to estimate these built-in models is decreased from nine to five by an effective iteration method, considerably reducing computational requirements.

The proposed model, in contrast to the previous complex nine-parameter three-diode model, simplifies the modeling and analysis process by requiring only five parameters. To ensure the reliability and accuracy of this proposed model, its results were carefully compared with datasheet values under standard test conditions (STC). This model was implemented using MATLAB/Simulink and validated using a polycrystalline solar cell under STC conditions.

The proposed three-diode model clearly outperforms the earlier existing two-diode model in terms of accuracy and performance, especially in lower irradiance settings, according to the results and comparison analysis.

Non-linear power–voltage characteristics of solar cell and frequently changing output due to variation in solar irradiance caused by movement of clouds are the major issues need to be considered in photovoltaic (PV) penetration to maintain the power quality of the grid. It is important for a PV module to always function at its maximum available power point to increase the efficiency and to maintain the grid stability. A possible solution to mitigate these generation fluctuations is the use of an electric double-layer capacitor or supercapacitor energy storage device, which is an efficient storage device for power smoothing applications. This study aims to propose a power smoothing control approach to smoothen out the output power variations of a solar PV system using a supercapacitor energy storage device.

To extract the maximum possible power from a PV panel, there are several maximum power points tracking (MPPT) algorithms developed in literature. Fuzzy logic controller-MPPT method is used in this work as it is a very efficient and popular technique which responds quickly under varying ecological conditions, reduced computational complexity and does not depend on any system constraints. Fuzzy logic-based MPPT controller by Boost DC–DC converter is developed for operating the PV panels at available maximum power point. Fuzzy logic-proportional integral (PI) charge controller is implemented by Buck–Boost converter to provide the constant current and suitable voltage for supercapacitor and to achieve better power smoothing. PI charge controller is preferred in this work as it offers better outcomes and is very easy to implement.

Simulation results conclude that the proposed power smoothing control approach can efficiently smooth out the power variations under variable irradiance and temperature situations. To confirm the accurateness of the proposed system, it is validated for poly-crystalline PV module and comparison of results is done by using different case study with and without the use of an energy storage system under change in irradiance condition. The proposed system is developed and examined on MATLAB/Simulink environment.

The performance comparison between PV power output with and without the use of a supercapacitor energy storage device under different Case Studies shows that the improved performance in smoothing of power output was achieved with the use of a supercapacitor energy storage device.

These implementations not only generate excessive voltage levels to enhance the quality of power but also include a detailed investigating of the various modulation methods and control schemes for multilevel inverter (MLI) topologies. Reduced harmonic modulation technology is used to produce 11-level output voltage with the production of renewable energy applications. The simulation is done in the MATLAB/Simulink for 11-level symmetric MLI and is correlated with the conventional inverter design.

This paper is focused on investigating the different types of asymmetric, symmetric and hybrid topologies and control methods used for the modular multilevel inverter (MMI) operation. Classical MLI configurations are affected by performance issues such as poor power quality, uneconomic structure and low efficiency.

The variations in both carrier and reference signals and their performance are analyzed for the proposed inverter topologies. The simulation result compares unipolar and bipolar pulse-width modulation (PWM) techniques with total harmonic distortion (THD) results. The solar-fed 11-level MMI is controlled using various modulation strategies, which are connected to marine emergency lighting loads. Various modulation techniques are used to control the solar-fed 11-level MMI, which is connected to marine emergency lighting loads. The entire hardware system is controlled by using SPARTAN 3A field programmable gate array (FPGA) board and the least harmonics are obtained by improving the power quality.

The simulation result compares unipolar and bipolar PWM techniques with THD results. Various modulation techniques are used to control the solar-fed 11-level MMI, which is connected to marine emergency lighting loads. The entire hardware system is controlled by a SPARTAN 3A field programmable gate array (FPGA) board, and the power quality is improved to achieve the lowest harmonics possible.

Renewable energy sources such as solar photovoltaic (PV) and wind are ubiquitous because of their lower environmental impact. Output from solar PV and wind turbines is unstable; hence, this article aims to propose an effective controller to extract maximum available power.

By focusing on the varying nature of solar irradiance and wind speed, the paper presents the maximum power point tracking (MPPT) technique for renewable energy sources, and power regulation is made by the novel inverter design. Moreover, a DC–DC boost converter is adopted with solar PV, and a doubly fed induction generator is connected with the wind turbine. The proposed MPPT technique is used with the help of a rain optimization algorithm (ROA) based on bi-directional long short-term memory (Bi-LSTM) (ROA_Bi-LSTM). In addition, the sinusoidal pulse width modulation inverter is used for DC–AC power conversion.

The proposed MPPT technique has jointly tracked the maximum power from solar PV and wind under varying climatic conditions. The power flow to the transmission line is stabilized to protect the load devices from unregulated frequency and voltage deviations. The power to the smart grid is regulated by three-level sinusoidal pulse width modulation inverter.

The methodology and concept of the paper are taken by the author on their own. They have not taken a duplicate copy of any other research article.

The purpose of this paper is to present a novel approach to the determination of the maximum power point (MPP) in the photovoltaic system using genetic algorithm (GA). The optimization is realised on two types of photovoltaic (PV) modules: monocrystalline and polycrystalline solar modules, with the same rated peak power (400 Wp) but different electrical output data.

The proposed algorithm is a nature-based algorithm that uses genetic operators such as reproduction, crossover and mutation to realise the search through the investigated area of solutions. To determine the MPP of the PV modules, a two-diode model of a PV cell is used. Based on the input electrical data for the analysed PV module, as well as the mathematical model of the PV, the algorithm can estimate the current and voltage at the MPP for given solar irradiation and cell temperature. The analysis is made for several different irradiations, but in work, the results are presented for irradiations of: 100, 500 and 1,000 W/m² and cell temperatures of 0, 25 and 40 °C.

From the presented results and performed analysis, it can be concluded that GA gives adequate results for both modules and for all working conditions. From the obtained results, it can be concluded that the optimization algorithm performs better when applied to the monocrystalline module works better especially in conditions with larger cell temperature, in comparison with the performance of the optimization algorithm applied to the polycrystalline module. On the other hand, the optimization algorithm applied to the polycrystalline module works better for the other working scenarios with smaller cell temperatures.

From the performed analysis, it can be concluded that the use GA as an optimization tool for the determination of the MPP can be successfully implemented. In addition, to improve the overall performance of the PV system, it is also necessary to forecast the weather conditions of the location where the PV system would be installed to forecast the cell temperature and the solar irradiation. This is necessary to choose the right PV module and inverter for the given location.

An optimization technique using GA as an optimization tool has been developed and successfully applied in the determination of the MPP for a PV system. The results are compared with the analytically determined values as well as with the values given by the producer, and they show good agreement.

A numerical simulation study of a Tandem solar cell is presented. The parameters of single and two-diodes lumped-circuit model are usually the saturation current, the series resistance, the ideality factor, the shunt resistance and the photocurrent. It is found that the influence of the distributed series resistance on electrical characteristics can be described numerically by the application of the two models to Tandem organic solar cells. A description of the efficiency, fill factor, open circuit voltage and short circuit current on the devices are marked with series resistance, temperature and ideality factor. This approach allows one to obtain a set of parameters which is reasonable and representative of the physical system.

This paper aims to achieve accurate maximum power from solar photovoltaic (PV), its five parameters need to be estimated. This study proposes a novel optimization technique for parameter estimation of solar PV.

To extract optimal parameters of solar PV new optimization technique based on the Jellyfish search optimizer (JSO). The objective function is defined based on two unknown variables and the proposed technique is used to estimate the two unknown variables and the rest three unknown variables are estimated analytically.

In this paper, JSO is used to estimate the parameters of a single diode PV model. In this study, eight different PV panels are considered. In addition, various performance indices, such as PV characteristics, such as power-voltage and current-voltage curves, relative error (RE), root mean square error (RMSE), mean absolute error (MAE) and normalized mean absolute error (NMAE) are determined using the proposed algorithm and existing algorithms. The results for different solar panels have been obtained under varying environmental conditions such as changing temperature and constant irradiance or changing irradiance and constant temperature.

The proposed technique is new and provides better results with minimum RE, RMSE, NMAE, MAE and converges fast, as depicted by the fitness graph presented in this paper.

Partial shading causes significant power decreases in the PV systems. The purpose of this paper is to address this problem, connectivity regulation is designed to reduce partial shading problems.

In this approach, the partial shading was estimated and dispersed evenly on the whole array by global shade dispersion technique (GSD). The grey wolf algorithm was implemented for the interconnection of arrays by an efficient switching matrix.

After the implementation of the GSD technique using a grey wolf algorithm, the performance under different shading conditions was analyzed using the MatLab simulation tool. The results were compared with total cross-tied (TCT), Su Do Ku and the proposed method of reconfiguration, where the proposed method improves the maximum power of the PV system appropriately.

This methodology uses any size of PV systems.

Replacement of conventional energy systems with renewable energy systems such as solar helps the environment clean and green.

The GSD interconnection scheme using the grey wolf optimization algorithm has proved an improved output performance compared with the existing TCT and Sudoku based reconfiguration techniques. By comparing with existing techniques in literature, the proposed method is more advantageous for reducing mismatch losses between the modules of any size of the PV array with less operating time.