Search results

This paper aims to forecast the availability of used but operational electric vehicle (EV) batteries to integrate them into a circular economy concept of EVs' end-of-life (EOL) phase. Since EVs currently on the roads will become obsolete after 2030, this study focuses on the 2030–2040 period and links future renewable electricity production with the potential for storing it into used EVs' batteries. Even though battery capacity decreases by 80% or less, these batteries will remain operational and can still be seen as a valuable solution for storing peaks of renewable energy production beyond EV EOL.

Storing renewable electricity is gaining as much attention as increasing its production and share. However, storing it in new batteries can be expensive as well as material and energy-intensive; therefore, existing capacities should be considered. The use of battery electric vehicles (BEVs) is among the most exciting concepts on how to achieve it. Since reduced battery capacity decreases car manufacturers' interest in battery reuse and recycling is environmentally hazardous, these batteries should be integrated into the future electricity storage system. Extending the life cycle of batteries from EVs beyond the EV's life cycle is identified as a potential solution for both BEVEOL and electricity storage.

Results revealed a rise of photovoltaic (PV) solar power plants and an increasing number of EVs EOL that will have to be considered. It was forecasted that 6.27–7.22% of electricity from PV systems in scenario A (if EV lifetime is predicted to be 20 years) and 18.82–21.68% of electricity from PV systems in scenario B (if EV lifetime is predicted to be 20 years) could be stored in batteries. Storing electricity in EV batteries beyond EV EOL would significantly decrease the need for raw materials, increase energy system and EV sustainability performance simultaneously and enable leaner and more efficient electricity production and distribution network.

Storing electricity in used batteries would significantly decrease the need for primary materials as well as optimizing lean and efficient electricity production network.

Energy storage is one of the priorities of energy companies but can be expensive as well as material and energy-intensive. The use of BEV is among the most interesting concepts on how to achieve it, but they are considered only when in the use phase as vehicle to grid (V2G) concept. Because reduced battery capacity decreases the interest of car manufacturers to reuse batteries and recycling is environmentally risky, these batteries should be used for storing, especially renewable electricity peaks. Extending the life cycle of batteries beyond the EV's life cycle is identified as a potential solution for both BEV EOL and energy system sustainability, enabling more efficient energy management performance. The idea itself along with forecasting its potential is the main novelty of this paper.

This study aims to computational numerical simulations to clarify and explore the influences of periodic cellular lattice (PCL) morphological parameters – such as lattice structure topology (simple cubic, body-centered cubic, z-reinforced body-centered cubic [BCCZ], face-centered cubic and z-reinforced face-centered cubic [FCCZ] lattice structures) and porosity value ( ) – on the thermal-hydraulic characteristics of the novel trussed fin-and-elliptical tube heat exchanger (FETHX), which has led to a deeper understanding of the superior heat transfer enhancement ability of the PCL structure.

A three-dimensional computational fluid dynamics (CFD) model is proposed in this paper to provide better understanding of the fluid flow and heat transfer behavior of the PCL structures in the trussed FETHXs associated with different structure topologies and high-porosities. The flow governing equations of the trussed FETHX are solved by the CFD software ANSYS CFX® and use the Menter SST turbulence model to accurately predict flow characteristics in the fluid flow region.

The thermal-hydraulic performance benchmarks analysis – such as field synergy performance and performance evaluation criteria – conducted during this research successfully identified demonstrates that if the high porosity of all PCL structures decrease to 92%, the best thermal-hydraulic performance is provided. Overall, according to the obtained outcomes, the trussed FETHX with the advantages of using BCCZ lattice structure at 92% porosity presents good thermal-hydraulic performance enhancement among all the investigated PCL structures.

To the best of the authors’ knowledge, this paper is one of the first in the literature that provides thorough thermal-hydraulic characteristics of a novel trussed FETHX with high-porosity PCL structures.

Lubricating oil leakage is a common issue in thermal power plant operation sites, requiring prompt equipment maintenance. The real-time detection of leakage occurrences could avoid disruptive consequences caused by the lack of timely maintenance. Currently, inspection operations are mostly carried out manually, resulting in time-consuming processes prone to health and safety hazards. To overcome such issues, this paper proposes a machine vision-based inspection system aimed at automating the oil leakage detection for improving the maintenance procedures.

The approach aims at developing a novel modular-structured automatic inspection system. The image acquisition module collects digital images along a predefined inspection path using a dual-light (i.e. ultraviolet and blue light) illumination system, deploying the fluorescence of the lubricating oil while suppressing unwanted background noise. The image processing module is designed to detect the oil leakage within the digital images minimizing detection errors. A case study is reported to validate the industrial suitability of the proposed inspection system.

On-site experimental results demonstrate the capabilities to complete the automatic inspection procedures of the tested industrial equipment by achieving an oil leakage detection accuracy up to 99.13%.

The proposed inspection system can be adopted in industrial context to detect lubricant leakage ensuring the equipment and the operators safety.

The proposed inspection system adopts a computer vision approach, which deploys the combination of two separate sources of light, to boost the detection capabilities, enabling the application for a variety of particularly hard-to-inspect industrial contexts.

This article aims to optimise energy use and consumption by integrating Lean Six Sigma methodology with the ISO 50001 energy management system standard in an Irish dairy plant operation.

This work utilised Lean Six Sigma methodology to identify methods to measure and optimise energy consumption. The authors use a single descriptive case study in an Irish dairy as the methodology to explain how DMAIC was applied to reduce energy consumption.

The replacement of heavy oil with liquid natural gas in combination with the new design of steam boilers led to a CO₂ footprint reduction of almost 50%.

A further longitudinal study would be useful to measure and monitor the energy management system progress and carry out more case studies on LSS integration with energy management systems across the dairy industry.

The novelty of this study is the application of LSS in the dairy sector as an enabler of a greater energy-efficient facility, as well as the testing of the DMAIC approach to meet a key objective for ISO 50001 accreditation.

The purpose of this paper is to propose a framework of green strategies as a combination of energy-efficiency measures and solutions towards environmental impact reduction for improving environmental sustainability at logistics sites. Such measures are examined by discussing the related impacts, motivations and barriers that could influence the measures' adoption. Starting from the framework, directions for future research in this field are outlined.

The proposed framework was developed starting from a systematic literature review (SLR) approach on 60 papers published from 2008 to 2022 in international peer-reviewed journals or conference proceedings.

The framework identifies six main areas of intervention (“green strategies”) towards green warehousing, namely Building, Utilities, Lighting, Material Handling and Automation, Materials and Operational Practices. For each strategy, specific energy-efficiency measures and solutions towards environmental impact reduction are further pinpointed. In most cases, “green-gold” measures emerge as the most appealing, entailing environmental and economic benefits at the same time. Finally, for each measure the relationship with the measures' primary impacts is discussed.

From an academic viewpoint, the framework fills a major gap in the scientific literature since, for the first time, this study elaborates the concept of green warehousing as a result of energy-efficiency measures and solutions towards environmental impact reduction. A classification of the main areas of intervention (“green strategies”) is proposed by adopting a holistic approach. From a managerial perspective, the paper addresses a compelling need of practitioners – e.g. logistics service providers (LSPs), manufacturers and retailers – for practices and solutions towards greener warehousing processes to increase energy efficiency and decrease the environmental impact of the practitioners' logistics facilities. In this sense, the proposed framework can provide valuable support for logistics managers that are about to approach the challenge of turning the managers' warehouses into greener nodes of the managers' supply chains.

A standalone microgrid (MG) is able to use local renewable resources and reduce the loss in long distance transmission. But the single-phase device in a standalone MG can cause the voltage unbalance condition and additional power loss that reduces the cycle life of battery. This paper proposes an energy management strategy for the battery/supercapacitor (SC) hybrid energy storage system (HESS) to improve the transient performance of bus voltage under unbalanced load condition in a standalone AC microgrid (MG).

The SC has high power density and much more cycling times than battery and thus to be controlled to absorb the transient and unbalanced active power as well as the reactive power under unbalanced condition. Under the proposed energy management design, the battery only needs to generate balanced power to balance the steady state power demand. The energy management strategy for battery/SC HESS in a standalone AC MG is validated in simulation study using PSCAD/EMTDC.

The results show that the energy management strategy of HESS maintains the bus voltage and eliminates the unbalance condition under single-phase load. In addition, with the SC to absorb the reactive power and unbalanced active power, the unnecessary power loss in battery is reduced with shown less accumulate depth of discharge and higher average efficiency.

With this technology, the service life of the HESS can be extended and the total cost can be reduced.

The decarbonization of power generation is key to achieving carbon neutrality in China by the end of 2060. This paper aims to examine how green finance influences China’s low-carbon transition of power generation. Using a provincial panel data set as an empirical study example, green finance is assessed first, then empirically analyses the influences of green finance on the low-carbon transition of power generation, as well as intermediary mechanisms at play. Finally, this paper makes relevant recommendations for peak carbon and carbon neutrality in China.

To begin with, an evaluation index system with five indicators is constructed with entropy weighting method. Second, this paper uses the share of coal-fired power generation that takes in total power generation as an inverse indicator to measure the low-carbon transition in power generation. Finally, the authors perform generalized method of moments (GMM) econometric model to examine how green finance influences China’s low-carbon transition of power generation by taking advantage of 30 provincial panel data sets, spanning the period of 2007–2019. Meanwhile, the implementation of the 2016 Guidance on Green Finance is used as a turning point to address endogeneity using difference-in-difference method (DID).

The prosperity of green finance can markedly reduce the share of thermal power generation in total electricity generation, which implies a trend toward China’s low-carbon transformation in the power generation industry. Urbanization and R&D investment are driving forces influencing low-carbon transition, while economic development hinders the low-carbon transition. The conclusions remain robust after a series of tests such as the DID method, instrumental variable method and replacement indicators. Notably, the results of the mechanism analysis suggest that green finance contributes to low-carbon transformation in power generation by reducing secondary sectoral share, reducing the production of export products, promoting the advancement of green technologies and expanding the proportion of new installed capacity of renewable energy.

This paper puts forward relevant suggestions for promoting the green finance development with countermeasures such as allowing low interest rate for renewable energy power generation, facilitating market function and using carbon trade market. Additional policy implication is to promote high quality urbanization and increase R&D investment while pursuing high quality economic development. The last implication is to develop mechanism to strengthen the transformation of industrial structure, to promote high quality trade from high carbon manufactured products to low-carbon products, to stimulate more investment in green technology innovation and to accelerate the greening of installed structure in power generation industry.

This paper first attempts to examine the low-carbon transition in power generation from a new perspective of green finance. Second, this paper analyses the mechanism through several aspects: the share of secondary industry, the output of exported products, advances in green technology and the share of renewable energy in new installed capacity, which has not yet been done. Finally, this study constructs a system of indicators to evaluate green finance, including five indicators with entropy weighting method. In conclusion, this paper provides scientific references for sustainable development in China, and meanwhile for other developing countries with similar characteristics.

The work described below compares three very different residential typologies in terms of their energy performance in operation. The purpose of this paper is to identify the influence of building typologies and corresponding urban morphologies on operational energy demand and the potential for building integrated energy production.

Two of the typologies studied are apartment buildings while the third comprises single-family homes located on small plots. An important factor under consideration is the insertion into the respective urban design configuration so that mutual shading of the buildings and the ensuing impact on energy performance is evaluated. Heating and cooling demands, as well as the potential for building-integrated electricity production were investigated for four different European climates in a dynamic thermal simulation environment.

The results show that the investigated apartment buildings have a lower operational energy demand than the single-family home in all climates. This advantage is most pronounced in cool climate conditions. At the same time the investigated single-family home has the highest potential for building integrated renewable energy production in all climates. This advantage is most pronounced in low latitudes.

The study builds up on generic buildings that are based on a common urban grid and are easily comparable and scalable into whole city districts. Still, these buildings are planned into such detail, that they provide fully functional floor plans and comply with national building regulations. This approach allows us to draw conclusions on the scale of individual buildings and at an urban scale at the same time.

One of the major challenges in the design of thermal equipment is to minimize the entropy production and enhance the thermal dissipation rate for improving energy efficiency of the devices. In several industrial applications, the structure of thermal device is cylindrical shape. In this regard, this paper aims to explore the impact of isothermal cylindrical solid block on nanofluid (Ag – H₂O) convective flow and entropy generation in a cylindrical annular chamber subjected to different thermal conditions. Furthermore, the present study also addresses the structural impact of cylindrical solid block placed at the center of annular domain.

The alternating direction implicit and successive over relaxation techniques are used in the current investigation to solve the coupled partial differential equations. Furthermore, estimation of average Nusselt number and total entropy generation involves integration and is achieved by Simpson and Trapezoidal’s rules, respectively. Mesh independence checks have been carried out to ensure the accuracy of numerical results.

Computations have been performed to analyze the simultaneous multiple influences, such as different thermal conditions, size and aspect ratio of the hot obstacle, Rayleigh number and nanoparticle shape on buoyancy-driven nanoliquid movement, heat dissipation, irreversibility distribution, cup-mixing temperature and performance evaluation criteria in an annular chamber. The computational results reveal that the nanoparticle shape and obstacle size produce conducive situation for increasing system’s thermal efficiency. Furthermore, utilization of nonspherical shaped nanoparticles enhances the heat transfer rate with minimum entropy generation in the enclosure. Also, greater performance evaluation criteria has been noticed for larger obstacle for both uniform and nonuniform heating.

The current numerical investigation can be extended to further explore the thermal performance with different positions of solid obstacle, inclination angles, by applying Lorentz force, internal heat generation and so on numerically or experimentally.

A pioneering numerical investigation on the structural influence of hot solid block on the convective nanofluid flow, energy transport and entropy production in an annular space has been analyzed. The results in the present study are novel, related to various modern industrial applications. These results could be used as a firsthand information for the design engineers to obtain highly efficient thermal systems.

This study aims to improve the availability of regenerative braking for urban metro vehicles by introducing a sensorless operational temperature estimation method for the braking resistor (BR) onboard the vehicle, which overcomes the vulnerability of having conventional temperature sensor.

In this study, the energy model based sensorless estimation method is developed. By analyzing the structure and the convection dissipation process of the BR onboard the vehicle, the energy-based operational temperature model of the BR and its cooling domain is established. By adopting Newton's law of cooling and the law of conservation of energy, the energy and temperature dynamic of the BR can be stated. To minimize the use of all kinds of sensors (including both thermal and electrical), a novel regenerative braking power calculation method is proposed, which involves only the voltage of DC traction network and the duty cycle of the chopping circuit; both of them are available for the traction control unit (TCU) of the vehicle. By utilizing a real-time iterative calculation and updating the parameter of the energy model, the operational temperature of the BR can be obtained and monitored in a sensorless manner.

In this study, a sensorless estimation/monitoring method of the operational temperature of BR is proposed. The results show that it is possible to utilize the existing electrical sensors that is mandatory for the traction unit’s operation to estimate the operational temperature of BR, instead of adding dedicated thermal sensors. The results also validate the effectiveness of the proposal is acceptable for the engineering practical.

The proposal of this study provides novel concepts for the sensorless operational temperature monitoring of BR onboard rolling stocks. The proposed method only involves quasi-global electrical variable and the internal control signal within the TCU.