Search results

The purpose of this paper is to present the design of a compact microstrip bandpass filter (BPF) in dual-mode configuration loaded with cross-loop and square ring slots on a square patch resonator for C-band applications.

In the proposed design, the dual-mode response for the filter is realized with two transmission zeros (TZs) by the insertion of a perturbation element at the diagonal corner of the square patch resonator with orthogonal feed lines. Such TZs at the edges of the passband result in better selectivity for the proposed BPF. Moreover, the cross-loop and square ring slots are etched on a square patch resonator to obtain a miniaturized BPF.

The proposed dual-mode microstrip filter fabricated in RT/duroid 6010 substrate using PCB technology has a measured minimum insertion loss of 1.8 dB and return loss better than 24.5 dB with a fractional bandwidth (FBW) of 6.9%. A compact size of 7.35 × 7.35 mm² is achieved for the slotted patch resonator-based dual-mode BPF at the center frequency of 4.76 GHz. As compared with the conventional square patch resonator, a size reduction of 61% is achieved with the proposed slotted design. The feasibility of the filter design is confirmed by the good agreement between the measured and simulated responses. The performance of the proposed filter structure is compared with other dual-mode filter works.

In the proposed work, a compact dual-mode BPF is reported with slotted structures. The conventional square patch resonator is deployed with cross-loop and square ring slots to design a dual-mode filter with a square perturbation element at its diagonal corner. The proposed filter exhibits compact size and favorable performance compared to other dual-mode filter works reported in literature. The aforementioned design of the dual-mode BPF at 4.76 GHz is suitable for applications in the lower part of the C-band.

This paper is aimed to study the design of a miniaturized filter with tri-band characteristics. In this paper, perturbation is used to realize circuit miniaturization and multi-band by exploiting the inductive property. During this process, vias are added for twofold benefit, namely, circuit miniaturization and enhanced frequency selectivity at high frequency. Thus, with the introduction of the shorting via, the single-band dual-mode bandpass filter is converted into a tri-band filter with a smaller electrical size.

This paper presents the design and characterization of a miniaturized two-port filter with tri-band operating characteristics. The proposed filter is constructed using a square patch resonator operating at 5.2 GHz with a capacitively coupled feed configuration. A square perturbation is added to the corner of the square patch to achieve diagonal symmetry and to excite dual mode. The perturbation offers a sharp transmission zero defining bandwidth of the proposed filter. In addition, a shorting post is introduced to achieve an 88% size reduction by lowering the operating frequency to 1.8 GHz.

The prototype filter has insertion less than 1.2 dB and return loss better than 12 dB throughout all the realized frequency bands. The prototype filter is fabricated and the simulation results are validated using experimental measurements. The realized fractional bandwidths of the proposed bandpass filter are 11/5.6/1 at 1.8/4.6/5.85 GHz, respectively. The quality factor of the proposed antenna is greater than 80 and a peak Q-factor of 387 is realized at 5.85 GHz. The high Q-factor indicates low loss and improved selectivity. The rejection levels in the stopband are greater than 20 dB.

The results indicate that the proposed filter is a suitable choice for low-power small-scale wireless systems operating in the microwave bands. The realized filter has the smallest footprint of 0.36λ_eff  × 0.19λ_eff where λ_eff is the effective wavelength calculated at the lowest frequency of operation.

Purpose of this study is to design a compact gap coupled anchor shape patch antenna for wireless local area network/high performance radio local area network and worldwide interoperability for microwave access applications.

An anchor shape microstrip antenna is conceived, designed, simulated and measured. The anchor shape antenna is transformed to its rectangular equivalent by conserving the patch area. Modeling and simulation of the antenna is performed by Ansys high frequency structure simulator (HFSS) electromagnetic solver based on the concept of finite element method. The simulated results are experimentally verified by using Agilent E5071C vector network analyzer. Theoretical analysis of an electromagnetically gap coupled anchor shape microstrip patch antenna has been performed by obtaining the lumped element equivalent of the transformed antenna.

The proposed antenna has a compact conducting patch of dimension 0.26λ × 0.12λ mm² (λ is calculated at lower resonating frequency of 3.56 GHz) with impedance bandwidths of 100 and 140 MHz and antenna gains of 1.91 and 3.04 dB at lower resonating frequency of 3.56 GHz and upper resonating frequency of 5.4 GHz, with omni-directional radiation pattern.

In literature, one does not encounter anchor shape antenna using the concept of gap coupling and parasitic patches. The design has been optimized for wireless local area network/worldwide interoperability for microwave access applications with a relatively low patch area (291.12 mm²) as compared to other reported antennas for wireless local area network/worldwide interoperability for microwave access applications. Transformed antenna and the actual experimental antenna behavior varies, but the resonant frequencies of the transformed antenna as observed by theoretical analysis and simulated results (by high frequency structure simulator) are reasonably close, and the percentage difference between the resonant frequencies (both at lower and upper bands) is within the permissible limit of 1-2.5 per cent. Results confirm the theoretical proposition of transformation of shapes in antenna design, which allows a designer to adapt the design shape according to the application.

This paper aims to present a low-cost, edge-fed, windmill-shaped, notch-band eliminator, circular monopole antenna which is practically loaded with a complementary split ring resonator (CSRR) in the middle of the radiating conductor and also uses a partial ground to obtain wide-band performance.

To compensate for the reduced value of gain and reflection coefficient because of the full (complete) ground plane at the bottom of the substrate, the antenna is further loaded with a partial ground and a CSRR. The reduction in the length of ground near the feed line improves the impedance bandwidth, and introduced CSRR results in improved gain with an additional resonance spike. This results in a peak gain 3.895dBi at the designed frequency 2.45 GHz. The extending of three arms in the circular patch not only led to an increase of peak gain by 4.044dBi but also eliminated the notch band and improved the fractional bandwidth 1.65–2.92 GHz.

The work reports a –10dB bandwidth from 1.63 GHz to 2.91 GHz, which covers traditional coverage applications and new specific uses applications such as narrow LTE bands for future internet of things (NB-IoT) machine-to-machine communications 1.8/1.9/2.1/2.3/2.5/2.6 GHz, industry, automation and business-critical cases (2.1/2.3/2.6 GHz), industrial, society and medical applications such as Wi-MAX (3.5 GHz), Wi-Fi3 (2.45 GHz), GSM (1.9 GHz), public safety band, Bluetooth (2.40–2.485 GHz), Zigbee (2.40–2.48Ghz), industrial scientific medical (ISM) band (2.4–2.5 GHz), WCDMA (1.9, 2.1 GHz), 3 G (2.1 GHz), 4 G LTE (2.1–2.5 GHz) and other personal communication services applications. The estimated RLC electrical equivalent circuit is also presented at the end.

Because of full coverage of Bluetooth, Zigbee, WiFi3 and ISM band, the proposed fabricated antenna is suitable for low power, low data rate and wireless/wired short-range IoT-enabled medical applications.

The antenna is fabricated on a piece (66.4 mm × 66.4 mm × 1.6 mm) of low-cost low profile FR-4 epoxy substrate (0.54 λ_g × 0.54 λ_g) with a dielectric constant of 4.4, a loss tangent of 0.02 and a thickness of 1.6 mm. The antenna reflection coefficient, impedance and VSWR are tested on the Keysight technology (N9917A) vector network analyzer, and the radiation pattern is measured in an anechoic chamber.

Compact and wideband antennas are the need of modern wireless systems that preferably work with compact, low-profile and easy-to-install devices that provide a wider coverage of operating frequencies. The purpose of this paper is to propose a novel compact and ultrawideband (UWB) microstrip patch antenna intended for high frequency wireless applications.

A square microstrip patch antenna was initially modeled on finite element method-based electromagnetic simulation tool high frequency structure simulator. It was then loaded with a rectangular slit and Koch snowflake-shaped fractal notches for bandwidth enhancement. The fabricated prototype was tested by using vector network analyzer from Agilent Technologies, N5247A, Santa Clara, California, United States (US).

The designed Koch fractal patch antenna is highly compact with dimensions of 10 × 10 mm only and possesses UWB characteristics with multiple resonances in the operating band. The −10 dB measured impedance bandwidth was observed to be approximately 13.65 GHz in the frequency range (23.20–36.85 GHz).

Owing to its simple and compact structure, positive and substantial gain values, high radiation efficiency and stable radiation patterns throughout the frequency band of interest, the proposed antenna is a suitable candidate for high frequency wireless applications in the K (18–27 GHz) and Ka (26.5–40 GHz) microwave bands.

The proposed structure consists of copper as a ground plane and 50 µm polyimide dielectric layer is placed in between the ground panel and top radiating patch. Octagon and pentagon shapes are combined to form a unit cell. This structure exhibits seven absorption peaks within the short frequency range 0.3–0.5 terahertz (THz) without any interference. Under normal incidence, this structure achieves the absorption of 96.9%, 95.3%, 98.7%, 91.7%, 96.5%, 95% and 97.8% at 0.3136 THz, 0.377 THz, 0.4060 THz, 0.4085 THz, 0.4240 THz, 0.4436 THz and 0.4648 THz, respectively. This study aims to provide a range of applications in THz dielectric sensing, thickness sensing, communications, wavelength selective radiation and detecting.

Multi-band THz metamaterial absorbers (MMA) from previous research are having a large unit size because of the presence of stacked layers and multiple resonators within a single unit cell. This leads to difficulty while implementing in practical applications. In this study, a new MMA has been presented at seven distinct frequencies without using stacked layers and multiple resonators.

This structure exhibits seven absorption peaks within the short frequency range 0.3–0.5 THz without any interference. Under normal incidence this structure achieves the absorption of 96.9%, 95.3%, 98.7%, 91.7%, 96.5%, 95% and 97.8% at 0.3136 THz, 0.377 THz, 0.4060 THz, 0.4085 THz, 0.4240 THz, 0.4436 THz and 0.4648 THz, respectively. The polarization and angle insensitivity of the design have been validated by numerical simulation up to 90° of oblique incidence. The effects of variation in geometrical parameters on absorption response are demonstrated. The physical mechanism of the structure is analysed by electric and magnetic field distributions. The resonant frequency ranges and the number of bands in this work are compared with previously reported papers. In THz range, this is the first time a single planar structure provides seven-band high-level absorption performance.

The highlights of the proposed seven-band THz MMA structure, in comparison with previous THz metamaterials, are as follows: this has a simple unit-cell structure and high resonant mechanism within the short frequency range 0.3–0.5 THz; this MMA can provide seven-band high-level absorption performance in a single planar structure for the first time in THz range; and this structure is polarization and incident angle independent in nature.

This paper aims to present a novel wireless passive pressure sensor based on an aperture coupled microstrip patch antenna embedded with an air cavity for pressure measurement.

In this paper, the sensitive membrane deformed when pressure was applied on the surface of the sensor and the relative permittivity of the mixed substrate changed, resulting in a change in the center frequency of the microstrip antenna. The size of the pressure sensor is determined by theoretical calculation and software simulation. Then, the sensor is fabricated separately as three layers using printed circuit board technology and glued together at last. The pressure test of the sensor is carried out in a sealed metal tank.

The extracted resonant frequency was found to monotonically shift from 2.219 to 1.974 GHz when the pressure varied from 0 to 300 kPa, leading to an average absolute sensitivity of 0.817 MHz/kPa.

This pressure sensor proposed here is mainly to verify the feasibility of this wireless passive maneuvering structure, and when the base material of this structure is replaced with some high-temperature-resistant material, the sensor can be used to measure the pressure inside the aircraft engine.

The sensor structure proposed here can be used to test the pressure in a high-temperature environment when the base material is replaced with some high-temperature-resistant material.

This paper aims to introduce a new novel microstrip monopulse comparator system to reduce the spurious radiation from the comparator and the feed network for achieving better radiation performance.

Two substrate layers have been used for the microstrip monopulse comparator system. The feed network and the comparator circuits are on the first substrate layer and the microstrip array antenna is on the second layer. The elements of the array antenna are novel square four-sided narrow rectangular slot antennas built on a conducting plane. A commercially available computational software, CST microwave studio, has been used for the analysis of the system.

Two substrate layers have been used for the microstrip monopulse comparator system. The feed network and the comparator circuits are on the first substrate layer and the microstrip array antenna is on the second layer. The elements of the array antenna are novel square four-sided narrow rectangular slot antennas built on a conducting plane. A commercially available computational software, CST microwave studio, has been used for the analysis of the system.

The system is proposed for tracking moving targets.

Novel slot radiators are introduced as radiating elements in this paper. The antenna arrangement shields the comparator and the feed network circuits, reducing the spurious radiation significantly.

Multichip modules provide short chip‐to‐chip interconnects in order to take advantage of the high speeds available in integrated circuits. One multichip approach utilises layers of embedded microstrip. In order to achieve the highest possible speed, it is necessary to use metals and dielectrics which have low relative dielectric constants and low loss. Polymer and polyimide dielectric materials hold great promise in MCM applications; however, their high frequency characteristics are often not well known. Since thin film dielectric properties may differ from the bulk properties, it is important to be able to determine the dielectric properties using on‐wafer measurement techniques rather than more conventional techniques. This paper focuses on some of the techniques available and discusses the advantages and shortcomings of different techniques for measuring dielectric properties.

This study aims to design a compact filtering monopole antenna for 5G communication. The design is most suited for various applications within the frequency range of 2.2–3.8 GHz. It offers enhanced bandwidth and reasonable gain with wide-stopband performance.

A low-pass filter (LPF) of complementary split ring resonator (CSRR) with short-circuited stub lines is integrated with a compact defected coplanar waveguide fed truncated circular monopole ultrawideband (UWB) antenna. The reference UWB antenna etched on an FR4 substrate was coupled to the designed LPF to transform the UWB antenna into a wideband antenna. The effect of coupling is analyzed based on the real and imaginary responses of the terminal impedance (ZT) curve. Three short-circuited stub lines of asymmetric lengths are added to the CSRR LPF to suppress harmonics, thereby enhancing the stopband performance and impedance matching between the elements. The proposed filtering antenna is fabricated using a photolithography process, and the corresponding results are measured using a network analyzer (N9951A). The radiation parameters of the proposed filtering monopole antenna are tested in the anechoic chamber. The simulated/measured results are compared and are found in agreement with each other.

The proposed design suppresses 6.5f0 harmonics, resulting in wide stopband performance and increased gain selectivity at the transition edge. A peak suppression of −41 dB and an average suppression of −18 dB were attained throughout the stopband. An operating fractional bandwidth of 54.5%/143% with a peak gain of 3 dBi/5 dBi was obtained. The proposed filtering antenna supports 5G applications such as WiMAX, WLAN, n7, n38 IMT-E, n30 WCS, n40 TDD, n41 TDD, n48 TDD, n78 TDD and n90 TDD.

The proposed design is novel and compact and has a wide application in 5G communication. With the filter, the antenna operates in wideband, and without the filter, it operates in UWB. Besides, it offers enhanced stopband performance with high gain selectivity at the transition edge. Comparatively, a 50% improvement in bandwidth, 52% improvement in size reduction and 33% improvement in harmonic suppression are attained.