Search results

This study aims to regarding the application of traditional pulse frequency modulation control full-bridge LLC resonant converters in wide output voltage fields such as on-board chargers, there are issues with wide frequency adjustment ranges and low conversion efficiency.

To address these issues, this paper proposes a fixed-frequency pulse width modulation (PWM) control strategy for a full-bridge LLC resonant converter, which adjusts the gain by adjusting the duty cycle of the switches. In the full-bridge LLC converter, the two switches of the lower bridge arm are controlled by a fixed-frequency and fixed duty cycle, with their switching frequency equal to the resonant frequency, whereas the two switches of the upper bridge arm are controlled by a fixed-frequency PWM to adjust the output voltage. The operation modes of the converter are analyzed in detail, and a mathematical model of the converter is established. The gain characteristics of the converter under the fixed-frequency PWM control strategy are deeply analyzed, and the conditions for implementing zero-voltage switching (ZVS) soft switching in the converter are also analyzed in detail. The use of fixed-frequency PWM control simplifies the design of resonant parameters, and the fixed-frequency control is conducive to the design of magnetic components.

According to the fixed-frequency PWM control strategy proposed in this paper, the correctness of the control strategy is verified through simulation and the development and testing of a 500-W experimental prototype. Test results show that the primary side switches of the converter achieve ZVS and the secondary side rectifier diodes achieve zero-current switching, effectively reducing the switching losses of the converter. In addition, the control strategy reduces the reactive circulating current of the converter, and the peak efficiency of the experimental prototype can reach 95.2%.

The feasibility of the fixed-frequency PWM control strategy was verified through experiments, which has significant implications for improving the efficiency of the converter and simplifying the design of resonant parameters and magnetic components in wide output voltage fields such as on-board chargers.

In real life, excitations are highly non-stationary in frequency and amplitude, which easily induces resonant vibration to structural responses. Conventional control algorithms in this case cannot guarantee cost-effective control effort and efficient structural response alleviation. To this end, this paper proposes a novel adaptive linear quadratic regulator (LQR) by integrating wavelet transform and genetic algorithm (GA).

In each time interval, multiresolution analysis of real-time structural responses returns filtered time signals dominated by different frequency bands. Minimization of cost function in each frequency band obtains control law and gain matrix that depend on temporal-frequency band, so suppressing resonance-induced filtered response signal can be directly achieved by regulating gain matrix in the temporal-frequency band, leading to emphasizing cost-function weights on control and state. To efficiently subdivide gain matrices in resonant and normal frequency bands, the cost-function weights are optimized by a developed procedure associated to genetic algorithm. Single-degree-of-freedom (SDOF) and multi-degree-of-freedom (MDOF) structures subjected to near- and far-fault ground motions are studied.

Resonant band requires a larger control force than non-resonant band to decay resonance-induced peak responses. The time-varying cost-function weights generate control force more cost-effective than time-invariant ones. The scheme outperforms existing control algorithms and attains the trade-off between response suppression and control force under non-stationary excitations.

Proposed control law allocates control force amounts depending upon resonant or non-resonant band in each time interval. Cost-function weights and wavelet decomposition level are formulated in an elegant manner. Genetic algorithm-based optimization cost-efficiently results in minimizing structural responses.

This paper aims to present an 8 kW LLC resonant converter designed for plasma power supply with higher efficiency and lighter structure. It presents how to solve the problems of large volume and weight, low performance and low efficiency of traditional plasma power supply.

At present, conventional silicon (Si) power devices’ switching performance is close to the theoretical limit determined by its material properties; the next-generation silicon carbide (SiC) power devices with outstanding advantages can be used to optimal design. This 8 kW LLC resonant converter prototype with silicon carbide (SiC) power devices with a modulated switching frequency ranges from 100  to 400 kHz.

The experimental results show that the topology, switching loss, rectifier loss, transformer loss and drive circuit of the full-bridge LLC silicon carbide (SiC) plasma power supply can be optimized.

Due to the selected research object (plasma power supply), this study may have limited universality. The authors encourage the study of high frequency resonant converters for other applications such as argon arc welding.

This study provides a practical application for users to improve the quality of plasma welding.

The experimental results show that the full-bridge LLC silicon carbide (SiC) plasma power supply is preferred in operation under conditions of high frequency and high voltage. And its efficiency can reach 98%, making it lighter, more compact and more efficient than previous designs.

This paper aims to develop resonant vibratory gyroscopes for high sensitive detection. The dynamic characteristics of resonant vibratory gyroscopes are investigated.

Firstly, the working principle and the dynamic output characteristics of the resonant vibratory gyroscope could be described by the damped Mathieu equation. Moreover, an approximate analytical method based on the small parameter perturbation has been used for the purpose of investigating the approximate solution of the damped Mathieu equation. Finally, to verify the feasibility of the approximate analytical method of the damped Mathieu equation, dynamic output characteristics’ experiments of the resonant vibratory gyroscope are built.

The theoretical analysis and numerical simulations show that the approximate solution of the damped Mathieu equation is close to the dynamic output characteristics of the resonant vibratory gyroscope. On the other hand, it is concluded from the tested result that there exists a correlation between the theoretical curve and the experimental data processing result, meaning the damped dynamics analytical method is effective in building resonant vibratory gyroscopes.

This paper seeks to establish a foundation for optimizing and testing the performance of the resonant vibratory gyroscope. To this end, the approximate analytical method of the damped Mathieu equation was discussed. The result of this research has proved that the dynamic characteristics based on the damped Mathieu equation is an effective approach and is instructional in the practical resonant sensor design.

This paper aims to better design the resonant tank parameters for LLC resonant converter. And, it is found that under heavy load, the voltage gain is affected by junction capacitors of the primary side switching and the parasitic parameters of the secondary side diodes converted to the primary side, which will cause the voltage gain decreased when the switching frequency decreased.

This paper proposes an optimization parameters design method to solve this problem, which was based on impedance model considering the parasitic parameters of switching devices and diodes.

The effectiveness of the proposed method is verified by impedance Bode plots and experimental results.

From the perspective of impedance modeling, this paper finds the reasons for the insufficient voltage regulation capability of LLC resonant converters under heavy load and finds solutions through analysis.

The purpose of this paper is to model and analyze energy transfer through near‐field resonant coupling for high power light‐emitting diode (HPLED) illumination, with the intention to increase the appreciation and use of the coupled mode theory (CMT) other than the usual equivalent circuit method.

The CMT is extensively used to analyze the wireless energy transfer system because of its generality, simplicity, accuracy and intuitive understanding of near‐field resonant energy coupling mechanism.

The CMT forms a general way to model and analyze the non‐radiative magnetic resonant coupling systems. It is suitable not only for low frequency coupling but also for high frequency (of million‐Hertz) in which the circuit parameters are not easily obtained. Optimal coupling condition corresponding to the maximum power transfer is identified based on the CMT, and the multiple limit cycle phenomenon caused by the nonlinear nature of the HPLED is also described on the CMT model.

This paper takes advantages of CMT, i.e. generality, simplicity, accuracy and intuitive understanding to analyze the near‐field resonant energy coupling system. Key characteristics of the systems are explored based on the CMT, not the usual equivalent circuit method. The influence of nonlinear nature of the high power LED on energy transfer is also investigated. This work seeks a more general way than conventional equivalent circuit method to model and analyze the resonant magnetic system and the results obtained could facilitate better understanding of the resonant magnetic coupling mechanism and optimal design of the near‐field energy transfer system.

Physical contact and traditional sensitive structure Physical contact and traditional pressure-sensitive structures typically do not operate well in harsh environments. This paper proposes a high-temperature pressure measurement system for wireless passive pressure sensors on the basis of inductively coupled LC resonant circuits.

This paper begins with a general introduction to the high-temperature pressure measurement system, which consists of a reader antenna inductively coupled to the sensor circuit, a readout unit and a heat insulation unit. The design and fabrication of the proposed measurement system are then described in detail.

A wireless passive pressure sensor without an air channel is fabricated using high-temperature co-fired ceramics (HTCC) technology and its signal is measured by the designed measurement system. The designed heat insulation unit keeps the reader antenna in a safe environment of 159.5°C when the passive sensor is located in a 900°C high-temperature zone continuously for 0.5 h. The proposed system can effectively detect the sensor’s resonance frequency variation in a high bandwidth from 1 to 100 MHz with a frequency resolution of 0.006 MHz, tested from room temperature to 500°C for 30 min.

Expensive and bulky equipment (impedance analyzers or network analyzers) restrict the use of the readout method outside the laboratory environment. This paper shows that a novel readout circuit can replace the laboratory equipment to demodulate the measured pressure by extracting the various sensors’ resonant frequency. The proposed measurement system realizes automatic and continuous pressure monitoring in a high-temperature environment with a coupled distance of 2.5 cm. The research finding is meaningful for the measurement of passive pressure sensors under a wide temperature range.

Due to the advantages of fast response, high positioning precision and large stiffness, the piezoelectric-actuated nanopositioning stage is widely used in the micro/nanomachining fields. However, due to the inherent nonlinear hysteresis of the piezoelectric-actuator, the positioning accuracy of nanopositioning stage is greatly degraded. Besides, the nanopositioning stage is always performed with repetitive trajectories as the reference signals in applications, which makes the hysteresis behavior periodic. To this end, an adaptive resonance suppression iterative learning control (ARS-ILC) is proposed to address the hysteresis effect. With this effort, the positioning accuracy of the nanopositioning stage is improved.

The hysteresis behavior is identified by the Prandtl–Ishlinskii model. By establishing a convergence function, it is demonstrated that the learnable band of ILC is restricted by the lightly damping resonance of nanopositioning stage. Then, an adaptive notch filter (ANF) with constrained poles and zeros is adopted to suppress the resonant peak. Finally, online stability supervision (OSS) is used to ensure that the estimated frequency converges to the resonant frequency.

A series of experiments were carried out in the nanopositioning stage, and the results validated that the OSS is available to ensure the convergence of the ANF. Furthermore, the learnable band was extended via ARS-ILC; thus, the hysteresis behavior of nanopositioning stage has been canceled.

Due to high accuracy and easy implementation, the ARS-ILC can be used in not only nanopositioning stage control but other fabrication process control with repetitive motion.

This paper aims to solve the problems of large hard switching loss and unclear resonant parameter design in the existing inverter power supply topology.

This paper proposes a simple and reliable two-stage isolated inverter composed of series quasi-resonant push-pull and external freewheeling diode full-bridge inverter. The power supply topology is analyzed, the topology mode is analyzed, the mathematical model of the converter is established and the DC gain of the converter is deduced. The relationship between the load and the output gain of the resonant tank is presented, a new resonant parameter design method is proposed, and the parameter design of the resonant element of the converter is clarified.

The resonant components of the converter are designed according to the proposed resonant parameter design method, and the correctness of the method is verified by simulation and the development and testing of a 500 W experimental prototype. After experimental tests, the peak efficiency of the experimental prototype can reach 94%. Because the experimental prototype achieves soft switching, the heat generation of the switch is greatly reduced, so the heavy heat sink is removed, and the volume is reduced by about 30% compared with the traditional power supply, and the total harmonic distortion of the output voltage is about 2%.

The feasibility of the scheme is verified by experiments, which is of great significance for improving the efficiency of the inverter power supply and parameter optimization.

This study aims to solve the problem that under light-load conditions, the output voltage regulation capability is lost due to the fact that the voltage gain of the LLC resonant converter does not decrease with the increase of the switching frequency.

In this paper, the impedance model considering the parasitic parameters of the primary and secondary sides is calculated under light-load conditions, the limitations of the previous method are explained and a new circuit improvement is proposed.

In this paper, an improved circuit is proposed, and the impedance Bode plot is used to verify that the circuit can effectively improve the voltage gain problem under light-load conditions. Finally, the experimental results verify the effectiveness of the proposed circuit through comparison with traditional solutions and circuits.

In this paper, the impedance model considering the parasitic parameters of the primary and secondary sides is calculated, the limitations of the previous method are explained and a new circuit improvement is proposed. When compared with the previous method, the proposed circuit improvement can suppress the voltage gain increase that occurs when the switching frequency increases to a certain level.