Search results

The purpose of this paper is to describe the pre‐design and sizing of a smart leading edge section which is developed in the project SADE (Smart High Lift Devices for Next Generation Wings), which is part of the seventh framework program of the EU.

The development of morphing technologies in SADE concentrates on the leading and trailing edge high‐lift devices. At the leading edge a smart gap and step‐less droop nose device is developed. For the landing flap a smart trailing edge of the flap is in the focus of the research activities. The main path in SADE follows the development of the leading edge section and the subsequent wind tunnel testing of a five meter span full‐scale section with a chord length of three meters in the wind tunnel T‐101 at the Russian central aero‐hydrodynamic institute (TsAGI) in Moscow.

The presented paper gives an overview over the desired performance and requirements of a smart leading edge device, its aerodynamic design for the wind tunnel tests and the structural pre‐design and sizing of the full‐scale leading edge section which will be tested in the wind tunnel.

SADE aims at a major step forward in the development and evaluation of the potential of morphing airframe technologies.

The purpose of this paper is to provide an overview of the design and experimental work of compliant wing and wingtip morphing devices conducted within the EU FP7 project NOVEMOR and to demonstrate that the optimization tools developed can be used to synthesize compliant morphing devices.

The compliant morphing devices were “designed-through-optimization”, with the optimization algorithms including Simplex optimization for composite compliant skin design, aerodynamic shape optimization able to take into account the structural behaviour of the morphing skin, continuum-based and load path representation topology optimization methods and multi-objective optimization coupled with genetic algorithm for compliant internal substructure design. Low-speed subsonic wind tunnel testing was performed as an effective means of demonstrating proof-of-concept.

It was found that the optimization tools could be successfully implemented in the manufacture and testing stage. Preliminary insight into the performance of the compliant structure has been made during the first wind tunnel tests.

The tools in this work further the development of morphing structures, which when implemented in aircraft have potential implications to environmentally friendlier aircrafts.

The key innovations in this paper include the development of a composite skin optimization tool for the design of highly 3D morphing wings and its ensuing manufacture process; the development of a continuum-based topology optimization tool for shape control design of compliant mechanisms considering the stiffness and displacement functions; the use of a superelastic material for the compliant mechanism; and wind tunnel validation of morphing wing devices based on compliant structure technology.

This paper seeks to focus on material combinations for flexible matrix composites (FMCs) and the production methods thereof. These materials enable a high flexibility in one direction while being very stiff in the other.

Tested were rubber, silicone and thermoplastic elastomer matrices with carbon fibers using different production methods. These tests focused on the impregnation of the fibers with the different matrices and the orthotropy of the produced materials.

In the paper, a production capability for large quantities of easy to use off‐the‐shelf material was developed. The produced material handles similar to prepreg material known from “classical” composite materials. Test specimens were manufactured and characterized for mechanical properties using tensile tests.

These FMC materials are envisaged for a new pneumatic actuation system for an aircraft's droop nose to replace the electro‐mechanical system designed in the SADE and SmartLED projects. Combining a tube‐like geometry and a variable fiber‐angle lay‐up enables a wide range of deformation possibilities (large design freedom of movement behaviour).

This paper aims to describe the selection of the ideal variable inlet concept group by using results of aerodynamic investigations, system safety analyses and integration studies.

Aerodynamic and functional inlet requirements are explained and variable inlet concept groups are introduced. The concept evaluation by means of a weighted point rating is presented. The respective concept groups are analysed and evaluated regarding economic, functional and safety requirements.

By means of this evaluation, the concept group that adjusts the inlet geometry by rigid segment repositioning is identified as most suitable concept group.

The early selection of the most suitable concept group enables more detailed subsequent concept investigations, potentially enabling the technology of variable inlets for future commercial aircraft.

The purpose of this paper is to focus on a morphing architecture, conceived to produce droop nose effect, thus preserving high lift performance and laminar flow.

A numerical approach was adopted. On the base of preliminary aerodynamic requirements, the main aspects of the actuation architecture were defined and then assessed through a genetic approach.

Two different working modalities of mentioned architecture were identified: the former implying the use of an actuator, the latter taking advantage of a tailored elastic element, able to actuate morphing under the action of aerodynamic loads, without the aid of actuators.

The research presented in this work refers to an optimisation process currently tailored on preliminary aerodynamic requirements (leading edge vertical displacement maximisation, leading edge radius increase).

The research shows the possibility of producing morphing on the leading edge zone, actuating droop nose effect on metallic (constant and pice wise thickness) and composite skins.

This paper aims to achieve an optimum flow separation control over the airfoil using a passive flow control method by introducing a bio-inspired nose near the leading edge of the National Advisory Committee for Aeronautics (NACA) 4 and 6 series airfoil. In addition, to find the optimised leading edge nose design for NACA 4 and 6 series airfoils for flow separation control.

Different bio-inspired noses that are inspired by the cetacean species have been analysed for different NACA 4 and 6 series airfoils. Bio-inspired nose with different nose length, nose depth and nose circle diameter have been analysed on airfoils with different thicknesses, camber and camber locations to understand the aerodynamic flow properties such as vortex formation, flow separation, aerodynamic efficiency and moment.

The porpoise nose design that has a leading edge with depth = 2.25% of chord, length = 0.75% of chord and nose diameter = 2% of chord, delays the flow separation and improves the aerodynamic efficiency. Average increments of 5.5% to 6° in the lift values and decrements in parasitic drag (without affecting the pitching moment) for all the NACA 4 and 6 series airfoils were observed irrespective of airfoil geometry such as different thicknesses, camber and camber location.

The two-dimensional computational analysis is done for different NACA 4 and 6 series airfoils at low subsonic speed.

This design improves aerodynamic performance and increases the structural strength of the aircraft wing compared to other conventional high lift devices and flow control devices. This universal leading edge flow control device can be adapted to aircraft wings incorporated with any NACA 4 and 6 series airfoil.

The results would be of significant interest in the fields of aircraft design and wind turbine design, lowering the cost of energy and air travel for social benefits.

Different bio-inspired nose designs that are inspired by the cetacean species have been analysed for NACA 4 and 6 series airfoils and universal optimum nose design (porpoise airfoil) is found for NACA 4 and 6 series airfoils.

This paper aims to study the effect of corrugated skins on the aerodynamic performance of the cambered NACA 0012 airfoils at different corrugations parameters, maximum cambers, Reynolds numbers and maximum camber locations.

In this work, numerical approach is concerned, and results are obtained based on the finite volume approach. To characterize the effect of corrugated skins, the NACA 0012-corrugated airfoil section is chosen as the base airfoil, and different cambered corrugated airfoil sections are obtained by inclusion the camber to the base airfoil. In this research, the corrugation shape is a sinusoidal wave and corrugated skins are in the aft 30 per cent of airfoil chord. To investigate the effect of corrugations on the cambered sections, the drag coefficient and averaged lift curve slope for the corrugated airfoils are compared to those of the corresponding smooth sections.

Results indicate that the effect of increase in the maximum camber and also Reynolds number on the relative zero-incidence drag coefficient is of little importance at low corrugation amplitudes, whereas at high corrugation, amplitude results in different behaviors. It is found that as the maximum camber increases, the deterioration in the relative curve slope introduced by corrugated skins is reduced, and reduction in this deterioration is significant for high corrugation amplitudes airfoils. It is shown that an increase in the maximum camber location has nearly no effect on the relative zero-incidence drag coefficient and also relative lift curve slope.

The outcome of the present research provides the clues for better understanding of the effect of different corrugations parameters on the aerodynamic performance of the unmanned air vehicles to have as high aerodynamic performance as possible in different mission profiles of such vehicles.

Reviews recent advances in rotorcraft technology as presented at a recent Royal Aeronautical Society conference on innovation in rotorcraft technology and the 1997 Paris Air Show. Reports research initiatives to improve key rotorcraft technologies in the areas of obstacle detection, vibration and noise reduction and smart structures. Also mentions advances in overcoming rotorcraft speed limitations through use of tiltrotor and tiltwing aircraft.

The purpose of this study illustrates the morphing effects around a large-scale high-lift configuration of the Airbus A320 with two elements airfoil-flap in the take-off position. The flow around the airfoil-flap and the near wake are analysed in the static case and under time-dependent vibration of the flap trailing-edge known as the dynamic morphing.

Experimental results obtained in the subsonic wind tunnel S1 of Institut de Mécanique des Fluides de Toulouse of a single wing are discussed with high-fidelity numerical results obtained by using the Navier–Stokes multi-block (NSMB) code with advanced turbulent modelling able to capture the predominant instabilities and coherent structure dynamics. An explanation of the dynamic time-dependent grid deformation is provided, which is used in the NSMB code to simulate the flap’s trailing-edge deformation in the morphing configuration. Finally, power spectral density is performed to reveal the coherent wake structures and their modification because of the morphing.

Frequency of vibration and amplitude of deformation effects are investigated for different morphing cases. Optimal morphing regions at a specific frequency and a slight deformation were able to attenuate the predominant natural shear-layer frequency and to considerably decrease the width of the von Kármán vortices with a simultaneous increase of aerodynamic performances.

The new concept of future morphed wings is proposed for a large scale A320 prototype at the take-off position. The dynamic morphing of the flap’s trailing-edge is simulated for the first time for high-lift two-element configuration. In addition, the wake analysis performed helped to show the turbulent structures according to the organised eddy simulation model.

What proof have the public, independent of the assertions of the makers, that all the firms whose products are sold indifferently by the shopkeepers use only the best materials; or, indeed, that a large number of the articles sold are not mixtures more or less objectionable or fraudulent ? This, in effect, is the question put by a writer in a West of England newspaper, and it might be used as a text upon which to write a lengthy homily on the adulteration question and on the astonishing gullibility of the public. As a matter of fact the only evidence of the character and quality of food and other products, in regard to which there is no independent guarantee, is that which is afforded by the standing of the makers, and to some extent of the firms which offer them for sale. And this evidence cannot, under any circumstances, be looked upon as constituting proof. The startling allegations so commonly put forward by advertisers with respect to their wares, while they may be ineffective in so far as thinking people are concerned, must nevertheless be found pecuniarily advantageous since the expense involved in placing them under the eyes of the public would otherwise hardly be incurred. Many of these advertised allegations are, of course, entirely unjustifiable, or are incapable of proof. It may be hoped that the lavish manner in which they are set out, and their very extravagance, may, in time, result in producing a general effect not contemplated by the advertisers. In the meantime it cannot be too often pointed out that proof, such as that which is required for the satisfaction of the retailer and for the protection of the public, can only be obtained by the exercise of an independent control, and, in certain cases, by the maintenance of efficient independent inspection in addition, so that a guarantee of a character entirely different to that which may be offered, even by a firm of the highest eminence, may be supplied.