Search results

The purpose of this paper is the design and experimental investigation of compact hybrid sound-absorbing materials presenting low-frequency and broadband sound absorption.

The hybrid materials combine microchannels and helical tubes. Microchannels provide broadband sound absorption in the middle frequency range. Helical tubes provide low-frequency absorption. Optimal configurations of microchannels are used and analytical equations are developed to guide the design of the helical tubes. Nine hybrid materials with 30 mm thickness are produced via additive manufacturing. They are combinations of one-, two- and four-layer microchannels and helical tubes with 110, 151 and 250 mm length. The sound absorption coefficient of the hybrid materials is measured using an impedance tube.

The type of microchannels (i.e. one, two or four layers), the number of rotations and the number of tubes are key parameters affecting the acoustic performance. For instance, in the 500 Hz octave band (α₅₀₀), sound absorption of a 30 mm thick hybrid material can reach 0.52 which is 5.7 times higher than the α₅₀₀ of a typical periodic porous material with the same thickness. Moreover, the broadband sound absorption for mid-frequencies is reasonably high with and α₁₀₀₀ > 0.7. The ratio of first absorption peak wavelength to structure thickness λ/T can reach 17, which is characteristic of deep-subwavelength behaviour.

The concept and experimental validation of a compact hybrid material combining a periodic porous structure such as microchannels and long helical tubes are original. The ability to increase low-frequency sound absorption at constant depth is an asset for applications where volume and weight are constraints.

The existing Nonlinear Dynamic Vibration Absorbers (NLDVAs) have the disadvantages of complex structure, high cost, high installation space requirements and difficulty in miniaturization. And most of the NLDVAs have not been applied to reality. To address the above issues, a novel Triple-magnet Magnetic Dynamic Vibration Absorber (TMDVA) with tunable stiffness, only composed of triple cylindrical permanent magnets and an acrylic tube, is designed, modeled and tested in this paper.

(1) A novel TMDVA is designed. (2) Theoretical and experimental methods. (3) Equivalent dynamics model.

It is found that adjusting the magnet distance can effectively optimize the vibration reduction effect of the TMDVA under different resonance conditions. When the resonance frequency of the cantilever changes, the magnet distance of the TMDVA with a high vibration reduction effect shows an approximately linear relationship with the resonance frequency of the cantilever which is convenient for the design optimization of the TMDVA.

Both the simulation and experimental results prove that the TMDVA can effectively reduce the vibration of the cantilever even if the resonance frequency of the cantilever changes, which shows the strong robustness of the TMDVA. Given all that, the TMDVA has potential application value in the passive vibration reduction of engineering structures.

This paper aims to solve the problems of large hard switching loss and unclear resonant parameter design in the existing inverter power supply topology.

This paper proposes a simple and reliable two-stage isolated inverter composed of series quasi-resonant push-pull and external freewheeling diode full-bridge inverter. The power supply topology is analyzed, the topology mode is analyzed, the mathematical model of the converter is established and the DC gain of the converter is deduced. The relationship between the load and the output gain of the resonant tank is presented, a new resonant parameter design method is proposed, and the parameter design of the resonant element of the converter is clarified.

The resonant components of the converter are designed according to the proposed resonant parameter design method, and the correctness of the method is verified by simulation and the development and testing of a 500 W experimental prototype. After experimental tests, the peak efficiency of the experimental prototype can reach 94%. Because the experimental prototype achieves soft switching, the heat generation of the switch is greatly reduced, so the heavy heat sink is removed, and the volume is reduced by about 30% compared with the traditional power supply, and the total harmonic distortion of the output voltage is about 2%.

The feasibility of the scheme is verified by experiments, which is of great significance for improving the efficiency of the inverter power supply and parameter optimization.

The purpose of this paper is to present investigations on the significant influence of the tube material and fin density on fluid elastic instability and vortex shedding in a parallel triangular finned tube array subjected to water cross flow.

The experiment was conducted on finned tube arrays with a fin height of 6 mm and fin density of 3 fins per inch (fpi) and 9 fpi. A dedicated setup has been developed to examine fluid elastic instability and vortex shedding. Nine parallel triangular tube arrays with a pitch to tube diameter ratio of 1.78 were considered. The plain tube arrays, coarse finned tube arrays and fine finned tube arrays each of steel, copper and aluminium materials were tested. Plain tube arrays were tested to compare the results of the finned tube arrays having an effective tube diameter same as that of the plain tube.

A significant effect of fin density and tube material with a variable mass damping parameter was observed on the instability threshold. In the parallel triangular finned tube array subjected to water cross flow, a delay in the instability threshold was observed with an increase in fin density. For steel and aluminium tube arrays, the natural frequency is 9.77 Hz and 10.38 Hz, which is close to each other, whereas natural frequency of the copper tubes is 7.40 Hz. The Connors’ stability constant K for steel and aluminium tube arrays is 4.78 and 4.87, respectively, whereas it is 5.76 for copper tube arrays, which increases considerably compared to aluminum and steel tube arrays. The existence of vortex shedding is confirmed by comparing experimental results with Owen’s hypothesis and the Strouhal number and Reynolds number relationship.

This paper’s results contribute to understand the effect of tube materials and fin density on fluid elastic instability threshold of finned tube arrays subjected to water cross flow.

This paper aims to provide an overview of the recent developments and new topologies of single-phase moving magnet linear oscillating actuators (MMLOAs). The key advantage of the MMLOA when compared with conventional LOA is the absence of screws, gears and crankshaft mechanism, which results in fewer mechanical parts, simple structure, easy fabrication, lower noise levels and negligible frictional losses.

The review included papers up to August 2021. The structural designs of alternative topologies are deliberated in detail, and their relative merits and demerits are evaluated. Specific design issues, including pole and tooth number combinations, stroke length, magnet pole ratio and split ratio, are investigated. The imperative phenomena of the resonance, as well as the adjustable stroke, are also discussed in detail.

The electromagnetic performance in terms of thrust force of selected MMLOA topologies is compared. It is observed that the MMLOA with flux bridge topology has the highest thrust force of 365 N because of the large volume of the permanent magnets (PMs) used, which consequently increased the mass of the mover but based on overall performance analysis, single-phase end ferromagnetic Halbach surface-mounted PM LOA has the highest efficiency around 92%.

This review provides a comparative analysis for different tubular MMLOA topologies based on design construction and their electromagnetic performances.

The purpose of this paper is mainly to know: (1) the sound absorption coefficient of porous composite structures constituted by a new kind of lightweight ceramic foam and perforated plate; (2) the availability of an equivalent porous material model, recently proposed by the present author, to these composite structures in sound absorption.

A kind of lightweight ceramic foam with bulk density of 0.38–0.56 g·cm-3 was produced by means of molding, drying and sintering. The effect of stainless steel perforated plate on sound absorption performance of the ceramic foam was investigated by means of JTZB absorption tester.

The results indicate that the sound absorption performance could be obviously changed by adding the stainless steel perforated plate in front of the porous samples and the air gap in back of the porous samples. Adding the perforated plate to the porous sample with a relatively large pore size, the sound absorption performance could be evidently improved for the composite structure. When the air gap is added to the composite structure, the first absorption peak shifts to the lower frequency, and the sound absorption coefficient could increase in the low frequency range.

Based on the equivalent porous material model and the “perforated plate with air gap” model, the sound absorption performance of the composite structures can be simulated conveniently to a great extent by using Johnson-Champoux-Allard model.

To simplify the circuit design and control complexity of the magnetic coupling resonant wireless charging system, the radio energy transmission constant current and constant voltage charging is realized.

The purpose of this study is to simplify the circuit design and control complexity of the magnetic coupling resonance wireless charging system, in order to achieve constant current and constant voltage charging for wireless energy transmission. First, the principle of LCC/S-S compensation structure is analyzed, and the equivalent mathematical model is established; then, the system characteristics under constant current and constant voltage mode are analyzed, and the design method of system parameters is given; finally, a simulation and experimental system is built to verify the correctness and feasibility of the theoretical analysis.

The results show that the proposed hybrid topology can achieve a constant current output of 2 A and a constant voltage output of 30 V under variable load conditions, and effectively suppress the current distortion problem under light load conditions. The waveform distortion rate of the inverter current is reduced from 33.97% to 10.45%.

By changing the high-order impedance characteristics of the compensation structure, the distortion of the current waveform under light load is suppressed, and the overall stability and efficiency of the system are improved.

This study aims to regarding the application of traditional pulse frequency modulation control full-bridge LLC resonant converters in wide output voltage fields such as on-board chargers, there are issues with wide frequency adjustment ranges and low conversion efficiency.

To address these issues, this paper proposes a fixed-frequency pulse width modulation (PWM) control strategy for a full-bridge LLC resonant converter, which adjusts the gain by adjusting the duty cycle of the switches. In the full-bridge LLC converter, the two switches of the lower bridge arm are controlled by a fixed-frequency and fixed duty cycle, with their switching frequency equal to the resonant frequency, whereas the two switches of the upper bridge arm are controlled by a fixed-frequency PWM to adjust the output voltage. The operation modes of the converter are analyzed in detail, and a mathematical model of the converter is established. The gain characteristics of the converter under the fixed-frequency PWM control strategy are deeply analyzed, and the conditions for implementing zero-voltage switching (ZVS) soft switching in the converter are also analyzed in detail. The use of fixed-frequency PWM control simplifies the design of resonant parameters, and the fixed-frequency control is conducive to the design of magnetic components.

According to the fixed-frequency PWM control strategy proposed in this paper, the correctness of the control strategy is verified through simulation and the development and testing of a 500-W experimental prototype. Test results show that the primary side switches of the converter achieve ZVS and the secondary side rectifier diodes achieve zero-current switching, effectively reducing the switching losses of the converter. In addition, the control strategy reduces the reactive circulating current of the converter, and the peak efficiency of the experimental prototype can reach 95.2%.

The feasibility of the fixed-frequency PWM control strategy was verified through experiments, which has significant implications for improving the efficiency of the converter and simplifying the design of resonant parameters and magnetic components in wide output voltage fields such as on-board chargers.

This study aims to synthesize new disperse dyes based on novel pyrazolyl quinolinone derivatives EQ1 and EQ2 and evaluate their characteristics after dyeing them on a polyester fabric.

New dispersed dyes based on pyrazolyl quinolinone derivatives were prepared and confirmed by different analyses, such as infrared spectroscopy, elemental microanalysis and nuclear magnetic resonance spectroscopy. They were dyed on a polyester fabric. The characteristics of dyed polyester were determined by color measurements such as a*, b*, L*, C*, E, Ho, R% and color strength. The electronic structures of EQ1 and EQ2 in gaseous state were investigated using density functional theory/B3LYP/6-311++G (d, p) level of theory.

The suitability of the prepared dyestuffs for dyeing on polyester fabrics has been investigated. The study was concerned with comparing the contrasting depth of shade and levelness. The study was concerned mainly with dye uptake and color measurements at two different temperatures. The results showed that the exhaustion values of dyes inside the polyester at 130°C were higher than those obtained at conventional dyeing temperature (100°C). The exhaustion values of EQ2 were greater than those of EQ1 at 130°C with 2.2%, while the brightness of EQ2 was higher than that of EQ1 at the two investigated temperatures. The results of molecular orbital calculations show that the studied compounds are planar. In addition, the ionization potential of EQ1 was lower than that of EQ2. The results of the theoretical study helped in understanding the dyeing behavior of the investigated azo dyes.

The prepared disperse dyes based on pyrazolyl quinolinone derivatives could be used in textile dyeing of polyester on an industrial scale.

Food safety is among the most important topics in the world. According to WHO guidelines, aflatoxins are one of the most hazardous food toxins. Therefore, their detection in food products seems crucial due to health problems. The purpose of this paper is to discuss the different types of biosensors in aflatoxin determination.

Traditional detection methods are time consuming and expensive. As fast and accurate detection is important in monitoring food contaminants, alternative analytical methods would be essential. Biosensors are the intelligent design of sensitive sensors for precise detection of toxins in a short time. Various biosensors are being applied for aflatoxins detection in food products with many advantages over the traditional methods.

Biosensors are cost-effective, stable and have possessed high selectivity, specificity and accuracy in aflatoxins detection. Applying biosensors has been increased recently, so biosensing methods (optical, electrochemical, piezoelectrical, immunosensors, surface plasmon resonance and calorimetric) are discussed along with their advantages in this article.

More efforts should be occurred to detect and decrease the aflatoxins by biosensors, and some traits like accuracy and selectivity would be the purpose of future projects. The combination of various techniques would also help in toxin detection issue in food products, so high efforts in this regard are also required for the upcoming years.

This article also reviews different types of biosensors simultaneously and explains their specificity for aflatoxin determination in different food products and also the future trends and requirements.