Search results

The mechanical and tribological properties of polymers and polymer composites vary with different environmental conditions. This paper aims to review the influence of humidity/water conditions on various polymers and polymer composites' mechanical properties and tribological behaviors.

The influence of humidity and water absorption on mechanical and tribological properties of various polymers, fillers and composites has been discussed in this paper. Tensile strength, modulus, yield strength, impact strength, COF and wear rates of polymer composites are compared for different environmental conditions. The interaction between the water molecules and hydrophobic polymers is also represented.

Pure polymer matrices show somewhat mixed behavior in humid environments. Absorbed moisture generally plasticizes the epoxies and polyamides and lowers the tensile strength, yield strength and modulus. Wear rates of PVC generally decrease in humid environments, while for polyamides, it increases. Fillers like graphite and boron-based compounds exhibit low COF, while MoS2 particulate fillers exhibit higher COF at high humidity and water conditions. The mechanical properties of fiber-reinforced polymer composites tend to decrease as the rate of humidity increases while the wear rates of fiber-reinforced polymer composites show somewhat mixed behavior. Particulate fillers like metals and advanced ceramics reinforced polymer composites exhibit low COF and wear rates as the rate of humidity increases.

The mechanical and tribological properties of polymers and polymer composites vary with the humidity value present in the environment. In dry conditions, wear loss is determined by the hardness of the contacting surfaces, which may not effectively work for high humid environments. The tribological performance of composite constituents, i.e. matrix and fillers in humid environments, defines the overall performance of polymer composite in said environments.

The issues concerning the prediction of changes in properties of polymer materials as a result of adding reinforcing fibers are currently widely discussed in the field of polymer material processing. This paper aims to present strengths and weaknesses of composites based on polymer materials strengthened with fibers. It touches upon composite cracking at the junction of a matrix and its reinforcement. It also discusses the analysis of changes in properties of chosen materials as a result of adding reinforcing fibers. The paper shows improvement in the strength of polymer materials with fiber addition, which is extremely important, because these types of composites are used in the aerospace, automotive and electrical engineering industries.

Comparing the properties of matrix strength with fiber properties is practically impossible. Thus, fiber tensile strength and composite tensile strength shall be compared (González et al., 2011): tensile (glass fiber GF) = 900 [MPa], elongation ΔL≈ 0; yield point (polyamide 66) = 70−90 [MPa], elongation Δ[%] = 3,5-18; tensile (polyamide 66 + 15% GF) = 80-125 [MPa], elongation Δ[%] ≈ 0; tensile (polyamide 66 + 30% GF) = 190 [MPa], elongation Δ[%] ≈ 0; yield point (polyamide 6) = 45-85 [MPa], elongation Δ[%] = 4-15; tensile (polyamide 6 + 15% GF) = 80-125 [MPa], elongation Δ[%] ≈ 0; tensile (polyamide 6 + 30% GF) = 95-130 [MPa] elongation Δ[%] ≈ 0. Comparison of properties of selected polymers and composites is presented in Tables 1−10 and Figures 1 and 2. The measurement methodology is presented in detail in the paper Kula et al. (2018). The increase in fiber content (to the extent discussed) leads to the increase in yield strength stresses and hardness. The value of yield strength for polyamide with the addition of fiberglass grows gradually with the increase in fiber content. The hardness of the composite of polyamide with glass balls increases together with the increase in reinforcement content. The changes of these values do not occur linearly. The increase in fiber content has a slight impact on density change (the increase of about 1 g/mm³ per 10 per cent).

The use of polymers as a matrix allows to give composites features such as: lightness, corrosion resistance, damping ability, good electrical insulation and thermal and easy shaping. Polymers used as a matrix perform the following functions in composites: give the desired shape to the products, allow transferring loads to fibers, shape thermal, chemical and flammable properties of composites and increase the possibilities of making composites. Fiber-reinforced polymer composites are the effect of searching for new construction materials. Glass fibers show tensile strength, stiffness and brittleness, while the polymer matrix has viscoelastic properties. Glass fibers have a uniform shape and dimensions. Fiber-reinforced composites are therefore used to increase strength and stiffness of materials. Polymers have low tensile strength, exhibit high deformability. Polymers reinforced by glass fiber have a high modulus of elasticity and therefore provide better the mechanical properties of the material. Composites with glass fibers do not exhibit deformations in front of cracking. An increase in the content of glass fiber in composites increases the tensile strength of the material. Polymers reinforced by glass fiber are currently one of the most important construction materials and are widely used in the aerospace, automotive and electro-technical industries.

The paper presents the test results for polyethylene composites with 25 per cent and 50 per cent filler coming from recycled car carpets of various car makes. The tests included using differential scanning calorimetry, testing material hardness, material tensile strength and their dynamic mechanical properties.

This study focuses on the structural performance assessment of hybrid polymer composites for pick-and-place robot grippers used in critical infrastructure. This research involved the creation of composite materials with different nanoparticle concentrations, followed by extensive testing to assess the mechanical properties of the materials, such as strength, stiffness and durability.

The composites comprised bidirectional interply inclined carbon fibers (C), S-glass fibers (SG), E-glass (EG), an epoxy matrix and silica nanoparticles (SNiPs). During construction, the composite materials must be carefully layered using quasi-static sequence techniques (45°C1/45°SG2/45°EG2/45°C1/45°EG2/45°SG2/45°C1) to obtain the epoxy matrix reinforcement and bonding using 0, 2, 4 and 6 wt. % of silica nanoparticles.

According to various test findings, the 4 wt. % of SNiPs added to polymer plates exhibits the maximum strength outcomes. The average results of the tensile and flexural tests for the polymer composite plates with 4 wt. % addition SNiPs were 127.103 MPa and 223.145 MPa, respectively. The average results of the tensile and flexural tests for the plates with 0 wt.% SNiPs were 115.457 MPa and 207.316 MPa, respectively.

The authors hereby attest that the research paper they have submitted is the result of their own independent and unique labor. All of the sources from which the thoughts and passages were derived have been properly credited. The work has not been submitted for publication anywhere and is devoid of any instances of plagiarism.

1. The study enhances the engineering materials for innovative applications.

2. The study explores the mechanical behavior of carbon/S-glass/E-glass fiber composites.

3. Silica nanoparticles were enhancing mechanical characteristics of the composite structure.

The study enhances the engineering materials for innovative applications.

The study explores the mechanical behavior of carbon/S-glass/E-glass fiber composites.

Silica nanoparticles were enhancing mechanical characteristics of the composite structure.

This study aims to discuss the effect of carbon nanotubes (CNTs) on the mechanical properties of acrylonitrile–butadiene–styrene (ABS) composites fabricated by additive manufacturing (AM). Insight into the energy-dissipation mechanisms introduced and/or enhanced by the addition of CNTs is presented in this study.

ABS/CNT filaments were fabricated with different concentrations of CNTs. Using a fused deposition modeling approach, unidirectional specimens were printed using a MakerBot Replicator 2X (MakerBot Industries, Brooklyn, NY, USA). Specimens were tested under static and dynamic conditions, with the loading coinciding with the printing direction, to determine elastic modulus, strength and viscoelastic properties.

A CNT reinforcing effect is evident in a 37 per cent increase in elastic modulus. Likewise, the strength of the composite increases by up to 30 per cent with an increase in weight fraction of CNTs. At low dynamic strain amplitudes (0.05 per cent), a correlation between dissipated strain energy of the butadiene phase and strength of the composite is found such that less dissipation, from constraint of the butadiene particles by the CNTs, leads to higher strength of the composite. At higher dynamic strains, the presence of a high concentration of CNT leads to increased energy dissipation, with a maximum measured value of 24 per cent higher loss factor compared to baseline specimens. Because the trend of the composite behavior is similar (with a higher absolute value) to that of neat ABS, this study’s results indicate that well-established polymer/CNT dissipation mechanisms (such as stick-slip) are not significant, but that the CNTs amplify the dissipation of the ABS matrix by formation of crazes through stress concentrations.

This study provides knowledge of the dissipation behavior in additively manufactured ABS/CNT composites and provides insight into the expansion to new printable materials for dynamics applications.

Damage induced during drilling of polymer matrix composites depends upon torque during drilling. Modeling of torque with feed rate and its control becomes imminent for damage free drilling of composite laminates. Therefore, the purpose of this paper is to construct a transfer function between drilling torque and feed rate based upon experiments. Thereafter, the torque is controlled by using PID controller.

This paper presents step-by-step procedure to capture complex drilling dynamics of polymer matrix composites in a mathematical model. A glass fiber reinforced plastic (GFRP) composite laminate is drilled at constant feed rate during experimentation. The corresponding time response of torque is recorded. First order, second order and third order transfer functions between torque and feed rate are identified using system identification toolbox of Matlab®. These transfer functions are then converted into state-space models. Experimental verification is performed on GFRP composite laminate. PID controller is designed using Simulink® to track a given reference torque during drilling of polymer matrix composite. The controller is then validated using different reference torque trajectories.

Good match is observed between torque response from state-space models and experiments. Error analysis based on integral absolute error and integral squared error on experimental and simulated response show that third-order system represents the complex drilling dynamics in a better way than first and second-order systems. PID controller effectively tracks given reference trajectories.

Third-order model between torque and feed rate for drilling of composites not available in literature has been presented. PID controller has previously been applied successfully for drilling of conventional materials, this paper extends implementation of PID torque control for drilling of composites.

As a high-performance engineering plastic, polyimide (PI) is widely used in the aerospace, electronics and automotive industries. This paper aims to review the latest progress in the tribological properties of PI-based composites, especially the effects of nanofiller selection, composite structure design and material modification on the tribological and mechanical properties of PI-matrix composites.

The preparation technology of PI and its composites is introduced and the effects of carbon nanotubes (CNTs), carbon fibers (CFs), graphene and its derivatives on the mechanical and tribological properties of PI-based composites are discussed. The effects of different nanofillers on tensile strength, tensile modulus, coefficient of friction and wear rate of PI-based composites are compared.

CNTs can serve as the strengthening and lubricating phase of PI, whereas CFs can significantly enhance the mechanical properties of the matrix. Two-dimensional graphene and its derivatives have a high modulus of elasticity and self-lubricating properties, making them ideal nanofillers to improve the lubrication performance of PI. In addition, copolymerization can improve the fracture toughness and impact resistance of PI, thereby enhancing its mechanical properties.

The mechanical and tribological properties of PI matrix composites vary depending on the nanofiller. Compared with nanofibers and nanoparticles, layered reinforcements can better improve the friction properties of PI composites. The synergistic effect of different composite fillers will become an important research system in the field of tribology in the future.

The purpose of this paper is to study a new method with which multi‐walled carbon nanotubes (MWNTs) can be dispersed and aligned in low density polyethylene (LDPE) for improving its mechanical properties.

Dispersion and alignment of MWNTs in LDPE matrix are enhanced by ultrasonic vibration, solution casting and melt mixing and flow moulding method. The properties of the composite are characterised using scanning electron microscopy, tensile testing machine and the Izod impact testing machine.

It is found that MWNTs in LDPE achieve some dispersion and alignment resulting in improvement in LDPE's strength and toughness.

Polymer/CNTs nanocomposites are expected to have good process ability of the polymers and high mechanical and functional properties of the CNTs. Enhancing dispersion and alignment of MWNTs in the polymer matrix will promote and expand the applications and development of polymer/MWNTs nanocomposites.

The method that enhances MWNTs dispersion and alignment in LDPE matrix provides a new way for alignment of other CNTs in polymer matrix.

This paper aims to evaluate and predict the tensile properties of additively manufactured continuous wire polymer composites (CWPCs).

An open-source 3D printer was modified to print CWPCs where metal wires act as a reinforcement within a polymer matrix. The influence of different wire materials and diameters on the tensile modulus and ultimate tensile strength was studied. Different polymer matrixes were used to investigate the effect of the matrix on CWPCs’ tensile properties. The behaviour of samples was predicted analytically using the rule of mixture micromechanical approach and investigated experimentally using an American society for testing and materials standard tensile test.

Experimental results showed improvement in the elastic modulus and ultimate strength of CWPCs compared with non-reinforced specimens. Deviation between the experimental data and the analytical prediction was found to be dependent on the matrix type, wire volume fraction and wire material.

This paper introduces novel continuous metal wire-reinforced 3D printed composites. The continuous wire inside the print can be used as a strain gauge which can give an early alert for material failure. Applications for CWPCs include 3D-printed pressure and temperature sensors which measure the change in the wire’s electrical resistance and 3D-printed heaters which would work by supplying current through continuous wires.

The aim of the this study is to develop a new class of composites which would be more commercially viable and environmentally sustainable via reduced resource depletion, as there has been global interest in utilization of natural resources. The dry sliding wear behavior of glass-epoxy (G-E)-based composites filled with tamarind kernel powder (TKP) in different volume fractions of fillers (0 per cent, 3 per cent and 6 per cent) was studied as per standards.

In the present study, the analysis and optimization of the wear process has been studied. The Taguchi approach to experimental design was used to identify the effect of wear parameters such as applied load, sliding velocity and sliding distance. Taguchi tools such as analysis of variance and multiple linear regression models have been used to analyze, obtain the significant parameters and evaluate the optimum combination levels of wear process parameters. The results of Taguchi analysis indicate that sliding distance was found to be the prominent parameter affecting wear volume loss compared to other wear parameters.

The G-E composites with 3 and 6 vol.% of TKP had the lowest wear volume loss. Multiple linear regression models for all the tested composites’ results well match with experimental results. Confirmation tests were conducted to validate the analysis. There was a close relationship between the experimental results and the statistical model.

However, to the best of author’s knowledge, these literature reports related to natural organic filler materials are limited to analysis of polymer matrix composite. Further, the addition of TKP particle as a potential filler has not been addressed. An attempt has been made to clarify the technical viability of TKP as a potential filler for G-E composite.

The ability of light‐weight all fiber‐reinforced polymer‐matrix composite armor and hybrid composite‐based armor hard‐faced with ceramic tiles to withstand the impact of a non‐Armor‐ Piercing (non‐AP) and AP projectiles is investigated using a transient non‐linear dynamics computational analysis. The results obtained confirm experimental findings that the all‐composite armor, while being able to successfully defeat non‐AP threats, provides very little protection against AP projectiles. In the case of the hybrid armor, it is found that, at a fixed overall areal density of the armor, there is an optimal ratio of the ceramic‐to‐composite areal densities which is associated with a maximum ballistic armor performance against AP threats. The results obtained are rationalized using an analysis based on the shock/blast wave reflection and transmission behavior at the hard‐face/air, hard‐face/backing and backing/air interfaces, projectiles’ wear and erosion and the intrinsic properties of the constituent materials of the armor and the projectiles.