Search results

This study aims to investigate the influence of polyepoxysuccinic acid sodium (PESA), a green antiscalant, on the nucleation, crystallization and precipitation of magnesium phosphate.

The conductivity method was used to investigate the maximum relative supersaturation of magnesium phosphate across various PESA dosages. Subsequently, a magnesium phosphate scale was prepared using the static scale inhibition method (GB/T16632-1996) and then analyzed via scanning electron microscopy.

The findings showed that PESA extends the induction period of magnesium phosphate crystallization, reduces crystal growth rate and elevates the solution’s relative supersaturation. Notably, PESA exerts a low dosage effect on inhibition of the magnesium phosphate scale, with the optimal dosage identified at 10 mL. Scanning electron microscopy revealed that PESA dispenses a dispersing effect on the magnesium phosphate scale, generating numerous concave, convex and deeper pores on the scale particles’ surface, and thereby significantly enhancing the surface area, especially when using an antiscalant with variable dosages.

This study sheds new light on the impact of PESA, a green antiscalant, on the crystallization and precipitation of magnesium phosphate, thus paving the way for the development of enhanced and eco-friendly scale inhibition strategies in future applications.

This paper aims to achieve phosphating via optimal features of Mg metal as a suitable base coating, which is considered for other properties such as barrier properties against the passage of several factors.

In this research, in the phosphate bath, immersion time, temperature and the content of sodium nitrite as an accelerator were changed.

As a result, increasing the immersion time of AZ31 Mg alloy samples in the phosphating bath as well as increasing the ratio of sodium dodecyl sulfate (SDS) concentration to sodium nitrite concentration in the phosphating bath formulation increase the mass of phosphating formed per unit area of the Mg alloy. The results of the scanning electron microscope test showed phosphating is not completely formed in short immersion times, which is a thin and uneven layer.

Mg and its alloys are sensitive to galvanic corrosion, which would lead to generating several holes in the metal. As such, it causes a decrease in mechanical stability as well as an unfavorable appearance.

Mg is used in several industries such as automobile and computer parts, mobile phones, astronaut compounds, sports goods and home appliances.

Nevertheless, Mg has high chemical reactivity, so an oxide-hydroxide layer is formed on its surface, which has a harmful effect on the adhesion and uniformity of the coating applied on Mg.

By increasing the ratio of SDS concentration to sodium nitrite concentration in the phosphating bath, the corrosion resistance of the phosphating increases.

This study aims to form composite solid lubricant coatings on the surface of bearing steel, which can significantly improve the tribological properties of thrust cylindrical roller bearings (TCRBs). Phosphating films possess microscopic porosity that typically needs to be sealed with oil, grease or wax. Due to its unique crystal structure, the phosphating film itself also exhibits a certain degree of lubricity. In this study, solid lubricants are used to fill the pores of the phosphating film. By combining the phosphating film with solid lubricants, lubrication and wear reduction can be achieved.

In this study, the surfaces of the shaft washer (WS) and seat washer (GS) were treated with zinc-phosphating. Subsequently, a solid lubricant solution (polytetrafluoroethylene [PTFE], MoS₂ and graphite) was sprayed onto the phosphated samples at concentrations of 1 , 2  and 3 g/L. The porous and adsorptive nature of the phosphating film was used to embed the solid lubricant particles into the film, thus forming a composite lubrication layer containing solid lubricants on the surface of the bearing steel.

The addition of solid lubricant materials has shown significant potential in reducing wear losses compared with phosphated samples without such additives. Increasing the amount of solid lubricant added can facilitate the formation of a transfer film, which further enhances the protective properties. However, it is important to note that excessive amounts of solid lubricant material can contribute to seizure, leading to increased wear losses of the cage and a higher average coefficient of friction (ACOF).By spraying a PTFE solution with a concentration of 2 g/L, the lowest ACOF and cage wear loss were achieved, resulting in reductions of 60.5% for the ACOF and 89.4% for the cage wear loss. Similarly, when spraying a graphite solution with a concentration of 3 g/L, the lowest wear losses for GS and WS were observed, with reductions of 51.7% for GS wear loss and 38.9% for WS wear loss.

The combination of the phosphating film and solid lubricants aims to achieve lubrication and wear reduction, providing a new approach to wear-resistant technology for TCRBs.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-07-2023-0231/

This study aims to provide a salt ready-mix to instant fried noodles manufacturers.

Response surface methodology was used to get optimized salt ready-mix based on carbonate salt, disodium phosphate, tripotassium phospahte, sodium hexametaphosphate and sodium chloride. Peak viscosity of flour and yellowness, cooking loss and hardness of noodles were considered as response factors for finding optimized salt formulation.

The results showed that salts have an important role in governing quality of noodles. Optimum levels of five independent variables of salts, namely, carbonate salt (1:1 mixture of sodium to potassium carbonate), disodium phosphate, sodium hexametaphosphate, tripotassium phosphate and sodium chloride were 0.64%, 0.29%, 0.25%, 0.46% and 0.78% on flour weight basis, respectively.

To the best of the authors’ knowledge, this is the first study to assess the effect of different combinations of different salts on the quality of noodles. These findings will also benefit noodle manufacturers, assisting in production of superior quality noodles.

This study aims to reveal the tribological mechanism of synergistic effect between MoDTC and P-containing additives in aluminum-based grease.

The authors prepared a molybdenum dialkyl dithiocarbamate (MoDTC) and revealed the tribological mechanism of synergistic effect between MoDTC and P-containing additives in aluminum-based grease by combining with ZDDP and P-containing and S-free additives.

The MoDTC the authors prepared has good friction-reducing and anti-wear properties in aluminum-based grease and has an obvious synergistic effect with ZDDP. MoDTC and ZDDP have a significant synergistic effect on the tribological properties in aluminum-based grease, mainly because of the formation of phosphates and metaphosphates as well as more MoS₂ in the friction film. P element plays a facilitating role in the chemical conversion of MoDTC to MoS₂.

The experiments of MoDTC with tributyl phosphate and trimethylphenyl phosphate confirm that the P element plays a facilitating role in the chemical conversion of MoDTC into MoS₂.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-12-2023-0410

This study aims to investigate the effect of electrodeposition parameters (i.e. time and voltage) on the properties of hydroxyapatite (HA) coating fabricated on Ti6Al4V surface.

A full factorial design along with response surface methodology was utilized to evaluate the main effect of independent variables and their relative interactions on response variables. The effect of electrodeposition voltage and deposition time on HA coatings Ca/P molar ratio and the size of deposited HA crystals were examined by structural equation modeling (SEM). The formation of plate-like and needle-like HA crystals was observed for all experiments.

The results obtained showed that the higher electrodeposition voltage leads to lower Ca/P values for HA coatings. This is more significant at lower deposition times, where at a 20-minute deposition time, the voltage increased from 2 to 3 V and the Ca/P decreased from 2.27 to 1.52. Full factorial design results showed that electrodeposition voltage has a more significant effect on the size of the deposited HA crystal. With increasing the voltage from 2 to 3 V at a deposition time of 20 min, the HA crystal size varied from 99 to 36 µm.

The investigation delved into the impact of two critical parameters, deposition time and voltage, within the electrodeposition process on two paramount properties of HA coatings. Analyzing the alterations in coating characteristics relative to variations in these process parameters can serve as a foundational guide for subsequent research in the domain of calcium-phosphate deposition for implants.

Using a combination of the geographical information system (GIS) and the Canadian water quality index (WQI), the current study sought to provide a long-term general assessment of the water quality of the Shatt Al-Arab River (SAAR), focusing on its suitability for living organisms. Likewise, SPSS statistics was used to develop a nonlinear WQI regression model for the study area.

The study required four decades of data collection on some environmental characteristics of river water. After that, calculate the WQI and conduct the spatial analysis. Eight variables in total, including water temperature, dissolved oxygen, potential hydrogen ions, electrical conductivity (EC), biological oxygen demand, turbidity, nitrate and phosphate, were chosen to calculate the WQI.

Throughout the study periods, the WQI values varied from 55.2 to 79.83, falling into the categories of four (marginal) and three (fair), with the sixth period (2007–2008) showing the most decline. The present research demonstrated that the high concentration of phosphates, the high EC values, and minor changes in the other environmental factors are the major causes of the decline in water quality. The variations in ecological variables' overlap are a senior contributor to changes in water quality in general. Notably, using GIS in conjunction with the WQI has shown to be very effective in reducing the time and effort spent on investigating water quality while obtaining precise findings and information at the lowest possible expense. Calibration and validation of the developed model showed that this model had a perfect estimate of the WQI value. Due to its flexibility and impartiality, this study recommends using the proposed model to estimate and predict the WQI in the study area.

Even though the water quality of the SAAR has been the subject of numerous studies, this is the only long-term investigation that has been done to evaluate and predict its water quality.

The purpose of this article is to provide information about interactions between pink-pigmented facultative methylotroph (PPFM) organisms and plants, their molecular mechanisms of methylotrophic metabolism, application of PPFMs in agriculture, biotechnology and bioremediation and also to explore lacuna in PPFMs research and direction for future research.

Research findings on PPFM organisms as potent plant growth promoting organisms are discussed in the light of reports published by various workers. Unexplored field of PPFM research are detected and their application as a new group of biofertilizer that also help host plants to overcome draught stress in poorly irrigated crop field is suggested.

PPFMs are used as plant growth promoters for improved crop yield, seed germination capacity, resistance against pathogens and tolerance against drought stress. Anti-oxidant and UV resistant properties of PPFM pigments protect the host plants from strong sunshine. PPFMs have excellent draught ameliorating capacity.

To meet the ever increasing world population, more and more barren, less irrigated land has to be utilized for agriculture and horticulture purpose and use of PPFM group of organisms due to their draught ameliorating properties in addition to their plant growth promoting characters will be extremely useful. PPFMs are also promising candidates for the production of various industrially and medicinally important enzymes and other value-added products. Wider application of this ecofriendly group of bacteria will reduce crop production cost thus improving economy of the farmers and will be a greener alternative of hazardous chemical fertilizers and fungicides.

Graphicalabstract:

The consolidation process and morphology evolution in ceramics-based additive manufacturing (AM) are still not well-understood. As a way to better understand the ceramic selective laser sintering (SLS), a dynamic three-dimensional computational model was developed to forecast thermal behavior of hydroxyapatite (HA) bioceramic.

AM has revolutionized automotive, biomedical and aerospace industries, among many others. AM provides design and geometric freedom, rapid product customization and manufacturing flexibility through its layer-by-layer technique. However, a very limited number of materials are printable because of rapid melting and solidification hysteresis. Melting-solidification dynamics in powder bed fusion are usually correlated with welding, often ignoring the intrinsic properties of the laser irradiation; unsurprisingly, the printable materials are mostly the well-known weldable materials.

The consolidation mechanism of HA was identified during its processing in a ceramic SLS device, then the effect of the laser energy density was studied to see how it affects the processing window. Premature sintering and sintering regimes were revealed and elaborated in detail. The full consolidation beyond sintering was also revealed along with its interaction to baseplate.

These findings provide important insight into the consolidation mechanism of HA ceramics, which will be the cornerstone for extending the range of materials in laser powder bed fusion of ceramics.

There is a strong inducement to develop new inorganic materials to substitute the current industrial pigments, which are known for their poor ultraviolet absorbent and low photoluminescence (PL) properties. The purpose of this paper is to invent a better rare-earth-based pigment material as a spectral modifier with good luminescence properties to enhance the spectral response for photovoltaic panel application.

Different phosphor samples made of nano-calcium carbonate (CaCO₃) with varied wt.% of the dopant Dysprosium doped calcium borophosphate (CBP/Dy) as (W0 – 0%, W1 – 3,85%, W2 – 7.41%, W3 –10.71% and W4 –13.79%) were prepared via the solid-state diffusion method at 600 °C for 6 h using a muffle furnace. The structural, morphological and luminescence properties of the CaCO₃:CBP/Dy powder samples were examined using scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and PL test.

The XRD, SEM and FTIR results verified the crystalline formation, morphological behaviour and vibration bonds of synthesized CBP/Dy-doped CaCO₃ powder samples. XRD pattern revealed that the synthesized powder samples exhibit crystalline structured materials, and SEM results showed irregular shape and porous-like structured morphologies. FTIR spectrum shows prominent bands at 712, 874 and 1,404 cm⁻¹, corresponding to asymmetric stretching vibrations of CO3²⁻ groups and out-of-plane bending. PL characterization of CBP/Dy-doped CaCO₃ (sample W) shows emission at 427 nm (λmax) under the excitation of 358 nm. The intensity of PL emission spectra drops due to the concentration quenching effect, while the maximum PL intensity is observed in the W3 phosphor powder system.

This phosphor powder is expected to find out the potential application such as a spectral modifier which is applied to match the energy of photons with solar cell bandgap to improve spectral absorption and lead to better efficiency.

The introduction of a nano-CaCO₃:CBP/Dy hybrid powder system with good luminescence properties to be used as spectral modifiers for solar cell application has been synthesized in the lab, which is a novel attempt.