Search results

The aim of this paper is to study the effect of laser shock peening (LSP) on mechanical behaviour of the laser-directed energy deposition (LDED)-based printed 15-5 PH stainless steel with U and V notches. The study specifically concentrates on the evaluation of effect of scan strategy, machining and LSP processing on microstructural, texture evolution and fatigue behaviour of LDED-printed 15-5 PH steel.

For LSP treatment, 15-5 PH steel was printed using LDED process with bidirectional scanning strategy (XX [θ = 0°) and XY [θ = 90°]) at optimised laser power of 600 W with a scanning speed of 300 mm/min and a powder feed rate of 3 g/min. Furthermore, LSP treatment was conducted on the V- and U-notched fatigue specimens extracted from LDED-built samples at laser energy of 3.5 J with a pulse width of 10 ns using laser spot diameter of 3 mm. Post to the LSP treatment, the surface roughness, fatigue life assessment and microstructural evolution analysis is performed. For this, different advanced characterisation techniques are used, such as scanning electron microscopy attached with electron backscatter diffraction for microstructure and texture, X-ray diffraction for residual stress (RS) and structure information, Vicker’s hardness tester for microhardness and universal testing machine for low-cycle fatigue.

It is observed that both scanning strategies during the LDED printing of 15-5 PH steel and laser peening have played significant role in fatigue life. Specimens with the XY printing strategy shows higher fatigue life as compared to XX with both U- and V-notched conditions. Furthermore, machining and LSP treatment led to a significant improvement of fatigue life for both scanning strategies with U and V notches. The extent of increase in fatigue life for both XX and XY scanning strategy with V notch is found to be higher than U notch after LSP treatment, though without LSP samples with U notch have a higher fatigue life. As fabricated sample is found to have the lowest fatigue life as compared to machines and laser peened with both scan strategies.

This study presents an innovative method to improve the fatigue life of 15-5 PH stainless steel by changing the microstructure, texture and RS with the adoption of a suitable scanning strategy, machining and LSP treatment as post-processing. The combination of preferred microstructure and compressive RS in LDED-printed 15-5 PH stainless steel achieved with a synergy between microstructure and RS, which is responsible to improve the fatigue life. This can be adopted for the futuristic application of LDED-printed 15-5 PH stainless steel for different applications in aerospace and other industries.

Powder bed fusion-laser beam (PBF-LB) is a rapidly growing manufacturing technology for producing Al-Si alloys. This technology can be used to produce high-pressure die-casting (HPDC) prototypes. The purpose of this paper is to understand the similarities and differences in the microstructures and properties of PBF-LB and HPDC alloys.

PBF-LB AlSi10Mg and HPDC AlSi10Mn plates with different thicknesses were manufactured. Iso-thermal heat treatment was conducted on PBF-LB bending plates. A detailed meso-micro-nanostructure analysis was performed. Tensile, bending and microhardness tests were conducted on both alloys.

The PBF-LB skin was highly textured and softer than its core, opposite to what is observed in the HPDC alloy. Increasing sample thickness increased the bulk strength for the PBF-LB alloy, contrasting with the decrease for the HPDC alloy. In addition, the tolerance to fracture initiation during bending deformation is greater for the HPDC material, probably due to its stronger skin region.

This knowledge is crucial to understand how geometry of parts may affect the properties of PBF-LB components. In particular, understanding the role of geometry is important when using PBF-LB as a HPDC prototype.

This is the first comprehensive meso-micro-nanostructure comparison of both PBF-LB and HPDC alloys from the millimetre to nanometre scale reported to date that also considers variations in the skin versus core microstructure and mechanical properties.

The nickel-based alloys Inconel 625 and Inconel 718 stand out due to their high strength and corrosion resistance in important industries like aerospace, aviation and automotive. Even though they are widely used, current techniques of producing materials that are difficult to cut pose several problems from a financial, ecological and even health perspective. To handle these problems and acquire improved mechanical and structural qualities, laser powder bed fusion (LPBF) has been widely used as one of the most essential additive manufacturing techniques. The purpose of this article is to focus on the state of the art on LPBF parts of Inconel 625 and Inconel 718 for microstructure, mechanical behavior and postprocessing.

The mechanical behavior of LPBF-fabricated Inconel is described, including hardness, surface morphology and wear, as well as the influence of fabrication orientation on surface quality, biocompatibility and resultant mechanical properties, particularly tensile strength, fatigue performance and tribological behaviors.

The postprocessing techniques such as thermal treatments, polishing techniques for surface enhancement, mechanical and laser-induced peening and physical operations are summarized.

The highlighted topic presents the critical aspects of the advantages and challenges of the LPBF parts produced by Inconel 718 and 625, which can be a guideline for manufacturers and academia in practical applications.

In this study, two postprocessing techniques, namely, conventional burnishing (CB) and ultrasonic-assisted burnishing (UAB), were applied to improve the fatigue behavior of 316 L stainless steel fabricated through selective laser melting (SLM). The effects of these processes on surface roughness, porosity, microhardness and fatigue performance were experimentally investigated. The purpose of this study is to evaluate the feasibility and effectiveness of ultrasonic-assisted burnishing as a preferred post-processing technique for enhancing the fatigue performance of additively manufactured components.

All samples were subjected to a sandblasting process. Next, the samples were divided into three distinct groups. The first group (as-Built) did not undergo any additional postprocessing, apart from sandblasting. The second group was treated with CB, while the third group was treated with ultrasonic-assisted burnishing. Finally, all samples were evaluated based on their surface roughness, porosity, microhardness and fatigue performance.

The results revealed that the initial mean surface roughness (Ra) of the as-built sample was 11.438 µm. However, after undergoing CB and UAB treatments, the surface roughness decreased to 1.629 and 0.278 µm, respectively. Notably, the UAB process proved more effective in eliminating near-surface pores and improving the microhardness of the samples compared to the CB process. Furthermore, the fatigue life of the as-built sample, initially at 66,000 cycles, experienced a slight improvement after CB treatment, reaching 347,000 cycles. However, the UAB process significantly enhanced the fatigue life of the samples, extending it to 620,000 cycles.

After reviewing the literature, it can be concluded that UAB will exceed the capabilities of CB in terms of enhancing the surface roughness and, subsequently, the fatigue performance of additive manufactured (AM) metals. However, the actual impact of the UAB process on the fatigue life of AM products has not yet been thoroughly researched. Therefore, in this study, this paper used the burnishing process to enhance the fatigue life of 316 L stainless steel produced through the SLM process.

In the denim industry, enzyme washing and its combination with stone washing are generally used to get the desired worn-out look. However, these conventional methods include high water, energy and time consumption. Nowadays, laser fading, which is a computer-controlled, dry, ecological finishing method, is preferred in the denim fading process. The purpose of this study is to observe the effects of chemical pretreatment applications on laser-faded denim fabric in terms of color and mechanical properties. To eliminate the enzyme washing process in denim fading and to minimize the disadvantages of laser fading, such as decreased mechanical properties and increased fabric yellowness, various chemical pretreatment applications were applied to the denim fabric before laser fading, followed by simple rinsing instead of enzyme washing.

Two different indigo-dyed, organic cotton denim fabrics with different unit weights were exposed to pretreatment processes and then laser treatment, followed by simple rinsing. Polysilicic acid, boric acid, borax and bicarbonate were used for pretreatment processes, and laser treatment was carried out under optimized laser parameters (40 dpi resolution and 300 µs pixel time). Tensile strength was tested, and color values (CIE L*, a*, b*, ΔE*, C* and h), color yield (K/S), yellowness and whiteness indexes were measured to identify the color differences.

Before laser fading, 30 g/L and 40 g/L polysilicic acid pretreatments for sulfur-indigo-dyed fabric and a mixture of 10 g/L boric acid and 10 g/L borax pretreatments for the fabric only indigo-dyed were recommended for the laser fading with sufficient mechanical properties and good color values.

With the chemical pretreatments defined in this study, it was possible to reduce yellowness and maintain the mechanical properties after laser fading, thus minimizing the disadvantages of laser treatment and also eliminating enzyme washing.

The purpose of this paper is to investigate the friction and wear mechanisms in lubricated sliding conditions of additively manufactured SS316L parts. The different viscous oils 5W30, 15W40, 20W50 and SAE140 are used. These investigations provide a theoretical basis for the high performance of printed and postheattreated SS316L.

Tribological tests were carried out on selective laser melting-made SS316L printed specimens and heat-treated specimens. The parameters in 15 min of test duration are 20 N of load, 200 rpm, 8 mm of pin diameter, 25 mm length, 80 mm of track diameter and EN31 counter disc body. This work presented the phenomena of lubrication regimes and their characterization, as identified by the Stribeck curve, and these regimes affect the tribological properties of additively manufactured SS316L under the influence of industrial viscous lubricants. The results are observed using Scanning electron microscope (SEM), X-ray diffraction (XRD) and wear tests.

The observations indicate that additively manufactured SS316L shows a reduced coefficient of friction (COF) and specific wear rate (SWR). This is credited to the utilization of different viscous lubricants.

This exclusive research demonstrates how various viscous lubricants affect the COF and SWR of printed and post-heat-treated SS316L parts. Lambda (λ), lubricant film thickness (h₀), surface roughness and wear mechanisms are studied and reported.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-04-2024-0110/

Liquid-assisted laser surface texturing technology was used to create composite microtextures on triangular guide rail surfaces to enhance their tribological properties.

Numerical simulations were used to investigate the impact of various microtextures on fluid dynamic lubrication. Reciprocating friction and wear tests, followed by mechanistic analysis, examined the combined tribological effects of microtextured surfaces and lubricants.

The numerical simulation outcomes reveal a significant augmentation in the influence of fluid dynamic pressure due to composite microtextures, consequently amplifying the load-bearing capacity of the oil film. The average friction coefficient of composite microtextured samples was approximately 0.136 in reciprocating pin-on-disk friction tests, representing approximately 17% decrease compared to polished samples. Triangular guide rails with composite microtextures demonstrated the lowest average coefficient under conditions of high-speed and heavy-loading in the reciprocating friction and wear tests. Additionally, the presence of composite microtextures was found to promote the formation of adsorbed and friction films during friction, potentially contributing to the enhancement of tribological properties.

Triangular guide rails face high friction and wear, limiting their stability in demanding applications like machine tool guideways. This paper proposes a novel approach for steel triangular guide rails, involving composite microtexturing, numerical fluid simulations, liquid-assisted laser surface texturing and friction-wear testing. By implementing composite microtextures, the method aims to reduce friction coefficients and extend guideway service life, thereby saving energy and reducing maintenance costs. Enhancing the antifriction and antiwear properties of machine tool guideways is crucial for improving performance and longevity.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-05-2024-0183/

Die edge quality with its corresponding die strength are two important factors for excellent dicing quality especially for low-k wafers due to their weak mechanical properties and fragile structures. It is shown in past literatures that laser dicing or grooving does yield good dicing quality with the elimination of die mechanical properties. This is due to the excess heat energy that the die absorbs throughout the procedure. Within the internal structure, the mechanical properties of low-k wafers can be further enhanced by modification of the material. The purpose of this paper is to strengthen the mechanical properties of wafers through the heat-treatment process.

The methodology of this approach is by heat treating several low-k wafers that are scribed with different laser energy densities with different laser micromachining parameters, i.e. laser power, frequency, feed speed, defocus reading and single/multibeam setup. An Nd:YAG ultraviolet laser diode that is operating at 355 nm wavelength was used in this study. The die responses from each wafer are thoroughly visually inspected to identify any topside chipping and peeling. The laser grooving profile shape and deepest depth are analysed using a laser profiler, while the sidewalls are characterized by scanning electron microscopy (SEM) to detect cracks and voids. The mechanical strength of each wafer types then undergoes three-point bending test, and the performance data is analyzed using Weibull plot.

The result from the experiment shows that the standard wafers are most susceptible to physical defects as compared to the heat-treated wafers. There is improvement for heat-treated wafers in terms of die structural integrity and die strength performance, which revealed a 6% increase in single beam data group for wafers that is processed using high energy density laser output but remains the same for other laser grooving settings. Whereas for multibeam data group, all heat-treated wafer with different laser settings receives a slight increase at 4% in die strength.

Heat-treatment process can yield improved mechanical properties for laser grooved low-k wafers and thus provide better product reliability.

Given the current friction and wear challenges faced by automobile parts and bearings, this study aims to identify a novel texture for creating anti-friction and wear-resistant surfaces. This includes detailing the preparation process with the objective of mitigating friction and wear in working conditions.

Femtosecond laser technology was used to create a mango-shaped texture on the surface of GCr15 bearing steel. The optimized processing technology of the texture surface was obtained through adjusting the laser scanning speed. The tribological behavior of the laser-textured surface was investigated using a reciprocating tribometer.

The friction coefficient of the mango-shaped texture surface is 25% lower than that of the conventional surface, this can be attributed to the reduced contact area between the friction ball and the micro-textured surface, leading to stress concentration at the extrusion edge and a larger stress distribution area on the contact part of the ball and disk compared to the conventional surface and the function of the micro-texture in storing wear chips during the sliding process, thereby reducing secondary wear.

The mango-shaped textured surface in this study demonstrates effective solutions for some of the friction and wear issues, offering significant benefits for equipment operation under light load conditions.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-04-2024-0127/

This study used an indentation-based mechanical testing framework for the mechanical characterization of laser powder bed fusion (LPBF) processed Inconel 718 on a wrought Inconel 718 substrate. The purpose of the paper is to investigate the effectiveness of the indentation-based approach for localized mechanical evaluation.

The LPBF-processed wrought substrate was sectioned into three sections for microstructural and mechanical characterization. A 3D heat source model was used for the thermal analysis of the interface region. The developed interface region is probed using the Knoop hardness indenter in different orientations to determine the textural anisotropy and mechanical behavior of the region.

LPBF process develops a melted interface zone (MIZ) at the deposition-substrate interface. The MIZ exhibited a coarse grain structure region along with a larger primary dendritic arm spacing (PDAS), signifying a slower cooling rate. FE modeling of the LPBF process reveals heat accumulation in the substrate along with intrinsic heat treatment (IHT) induced due to layer-wise processing. The obtained yield locus shows strong anisotropy in the deposition region, whereas reduced anisotropy with a nearly uniform ellipse locus for the MIZ regions. This reduced anisotropy is attributable to IHT and heat accumulation in the substrate.

An alternative localized mechanical characterization tool has been investigated in this work. The approach proved sensitive to thermal variations during LPBF processing in an isolated region which extends its suitability to variable geometry parts. Moreover, the approach could serve as a screening tool for parts made from dissimilar metals.