Search results

Quite often, concrete in structures is likely to get exposed to high temperatures, including an incident of fire. The strength-retention properties of concrete after such an exposure are of great importance in terms of the serviceability of buildings. This paper presents an experimental study on the strength retention and impermeability aspects of a set of self compacting, high-volume fly ash concrete mixes under elevated temperatures. Five selfcompacting concrete mixes with a higher 60% level of cement replacement with fly-ash, are designed and the effects of elevated temperatures, in the range of 200-800°C, on the physical, mechanical and durability properties of these mixes are assessed. The assessment is in terms of the weight losses and the reduction in the compressive strengths of concrete cubes and split tensile strengths of concrete cylinders. The durability characteristics are assessed in terms of RCPT test results on these mixes. Performances of these self compacting concrete mixes (SCC) at elevated temperatures are also compared with two normally-vibrated concrete mixes (NCs) of an equivalent M30 strength grade. Test results indicate that weight of the specimens significantly get reduced with an increase in the level of elevated temperature, with sharp variations beyond 600°C. The experimental results also show that large improvements against chloride-ion penetration and better strength-retention at higher temperatures can be realized with self-compacting high-volume fly-ash concrete mixes additionally admixed with GGBFS and silica fume.

Environmental issues caused by the production of Portland cement have led to it being replaced by waste materials such as fly ash, which is more economical and safer for the environment. Also, fly ash is a material with sustainable properties. Therefore, this paper aims to focus on the development of sustainable construction materials using 100% high-calcium fly ash and potassium hydroxide (KOH)-based alkaline solution and study the engineering properties of the resulting fly ash-based geopolymer concrete. Laboratory tests were conducted to determine the mechanical properties of the geopolymer concrete such as compressive strength, flexural strength, curing time and slump. In phase I of the study, carbon nanotubes (CNTs) were added to determine their effect on the strength of the geopolymer mortar. The results derived from the experiments indicate that mortar and concrete made with 100% fly ash C require an alkaline solution to produce similar (comparable) strength characteristics as Portland cement concrete. However, it was determined that increasing the amount of KOH generates a considerable amount of heat causing the concrete to cure too quickly; therefore, it is notable to forming a proper bond was unable to form a stronger bond. This study also determined that the addition of CNTs to the mix makes the geopolymer concrete tougher than the traditional concrete without CNT.

Tests were conducted to determine properties of the geopolymer concrete such as compressive strength, flexural strength, curing time and slump. In Phase I of the study, CNTs were studied to determine their effect on the strength of the geopolymer mortar.

The results derived from the experiments indicate that mortar and concrete made with 100% fly ash C require an alkaline solution to produce the same strength characteristics as Portland cement concrete. However, it was determined that increasing the amount of KOH generates too much heat causing the concrete to cure too quickly; therefore, it is notable to forming a proper bond. This study also determined that the addition of CNTs to the mix makes the concrete tougher than concrete without CNT.

This study was conducted at the construction engineering and management concrete laboratory at North Dakota State University in Fargo, North Dakota. All the experiments were conducted and analyzed by the authors.

The purpose of this paper is to explore the use of fly ash and graphite particles as low cost reinforcing materials for improved wear resistance, enhanced mechanical properties and reduction in density of hybrid composites.

The AlSi10Mg/fly ash/graphite (Al/FA/Gr) hybrid composite was synthesised by stir casting method. The dry sliding wear and friction behaviour of hybrid composites were studied using pin-on-disc machine by varying parameters like load and weight fraction of fly ash, and compared with the base metal alloy and aluminium-graphite composite. The tests were conducted with a constant sliding speed of 2 m/s and sliding distance of 2,400 m.

The hybrid composites exhibit higher hardness, higher tensile strength and lower density when compared to unreinforced alloy and aluminium-graphite composite. The incorporation of fly ash and graphite particles as reinforcements caused a reduction in the wear rate and coefficient of friction (COF) of the hybrid composites. The improvement in the tribological characteristics occured due to the load carrying capacity of hard fly ash particles and the formation of a lubricating film of graphite between the sliding interfaces. The wear rates and COF of unreinforced aluminium alloy and composites increase with an increase in the applied normal load. The wear rates and COF of hybrid composites decrease with an increase in the fly ash content. 9 wt.% fly ash and 3 wt.% graphite reinforced hybrid composite exhibited the highest wear resistance and lowest COF at all applied loads. Abrasive wear and delamination were dominant in the mild wear regime of aluminium alloy and composites. Due to subsurface deformation and crack propagation, plate-like wear debris were generated during delamination wear. In the severe wear regime, the dominant wear mechanism was adhesive wear with formation of transfer layers.

It is expected that these findings will contribute towards the development of lightweight and low cost aluminium products with improved tribological and mechanical properties.

The wear and friction data have been made available in this article for the use of Al/FA/Gr hybrid composites in tribological applications.

The purpose of this work is to improve the air entrainment capacity of a concrete by using fine mineral admixtures such as fly ash (FA) and silica fume (SF) as cement substitute, and coal bottom ash (CBA) as fine aggregate substitute. Air entrainment capacity has been studied indirectly as a measure of heat resistance of concrete. Literature has suggested that mineral admixtures improve the air absorption in the paste component of the concrete, on the one hand, whereas they perform pore and grain size refinement, on the other, thereby reducing the air entrainment. CBA, which being porous, creates the possibility of air adsorption by the aggregate component. Therefore, the study finds out whether a double benefit of adding both of these materials will be achieved, or CBA will try to improve the deficiency in the air entrainment created by the mineral admixtures.

Air-entrained concrete (AEC) mixes were constituted in three groups. First group represents mixes with natural fine aggregates only, and second with 25% fine aggregates substituted by CBA. Progressively, the third group has 50% fine aggregates substituted with CBA. In all the three groups, cement was substituted with FA and SF @ 0%, 20% and 40%, and 0%, 5% and 10%, respectively, thereby creating four binary and four ternary mixes corresponding to each group. Compressive and flexural strength tests were conducted at 28 days on the concrete mixes pre and post high-temperature heat treatment, i.e. 100°C, 200°C and 400°C, respectively. This study also examines the microstructure characteristics of AEC after 14 days of curing via X-ray diffraction. Sorptivity test was also conducted to estimate the capillary and air-entrained voids in concrete.

It was found that a concrete mix containing 20% FA and 10% SF along with 50% CBA could give similar post-heated strength to a normal (without mineral admixtures) AEC. In AECs where only CBA is present and cement paste is not substituted, both of the pre- and post-heated strengths of concrete reduce. Also, some mixtures containing large amounts of mineral admixtures in concrete with nil CBA show a high reduction in post-heated strength though they show good pre-heated strength. Therefore, mineral admixtures and CBA complement each other in improving the post-heated strength. Air pore structure found from sorptivity test also verifies these results.

AEC is very helpful for insulation of buildings during summer season by absorbing heat waves. AEC containing FA and CBA reduces carbon footprint because of substitution of cement and it also helps to conserve natural resources by the use of CBA in place of fine aggregates.

This paper aims to discuss the evaluation of the compressive and splitting tensile strength of concrete mixes containing different proportions of up to 20 per cent glass aggregate. Portions of sand in concretes with and without admixtures were replaced with measurements of glass aggregates.

“Glascrete” is a term used for concrete in which crushed glass is used as a substitute for all or part of the aggregates. Glass can be recycled many times without changing its properties, making it an ideal material in concrete. Overall, 144 cubes and 144 cylinders of glascretes were prepared with different admixtures and subjected to compressive and splitting tensile strength test.

A comparison with a 21-day control mix indicated that glass aggregates are replacing sand in concrete ranging from 5 to 20 per cent by volume, resulting in 3.8-10.6 per cent and 3.9-16.4 per cent fall in compressive and tensile strength, respectively. However, the use of mineral admixture improved the properties of the mixes at 3, 7, 14 and 21 days.

Cities worldwide are congested, and even those with the best waste-management system would have issues with waste disposal after the year 2030. Consequently, waste management is a current issue for cities all over the world.

This study aims to evaluate the physical properties of mortar mixes that contain different volumes of waste glass as substitutes for fine aggregate with or without additives. Mineral additives are used to improve the mechanical properties of glascrete mixes in addition to its chemical resistance by absorbing the OH⁻ ions responsible for the possible alkali-silica reaction (ASR). It also reduces the adverse effects of mix-dimensional stability. Water-reducing admixtures are used to reduce the impact of the ASR by minimizing the amount of moisture in concrete, in effect decreasing the possible expansion of any produced gel. In this research, compressive and splitting tensile strength of concrete mortar containing waste glass of limited substitutions is evaluated.

The purpose of this paper is to develop new predictive models using gene expression programming in order to estimate the compressive strength of green concrete, as accurate models that can predict the compressive strength of green concrete are still lacking.

To estimate the compressive strength of plain concrete, fly ash concrete, silica fume concrete and concrete with silica fume and fly ash, four predictive GEP models are developed. The GEP models are developed using a large and reliable database that is collected from the literature. The GEP models are validated using the collected experimental database.

The R² is used to statistically evaluate the performance of the GEP models wherein the R² values for the GEP models including all data are 85, 95, 80 and 95.3 percent for the models that predict the compressive strength of plain concrete, fly ash concrete, silica fume concrete and concrete with silica fume and fly ash, respectively.

The GEP models have high R² values and low RMSE and MAE, which indicates that they are capable of predicting the compressive strength of green concrete with a reasonable accuracy.

The purpose of this study is to experimentally determine whether mechanical properties of concrete can be improved by using olive pomace aggregates (OPA) as a substitute for natural sand. Two types of OPA were tested by replacing an equivalent amount of natural sand. The first type was OPA mixed with olive mill wastewater (OMW), and the second type was OPA not mixed with OMW. For each type, two series of concrete were produced using OPA in both dry and saturated states. The percentage of partial substitution of natural sand by OPA varied from 0% to 15%.

The addition of OPA leads to a reduction in the dry density of hardened concrete, causing a 5.69% decrease in density when compared to the reference concrete. After 28 days, ultrasonic pulse velocity tests indicated that the resulting material is of good quality, with a velocity of 4.45 km/s. To understand the mechanism of resistance development, microstructural analysis was conducted to observe the arrangement of OPA and calcium silicate hydrates within the cementitious matrix. The analysis revealed that there is a low level of adhesion between the cement matrix and OPA at interfacial transition zone level, which was subsequently validated by further microstructural analysis.

The laboratory mechanical tests indicated that the OPCD_OPW (5) sample, containing 5% of OPA, in a dry state and mixed with OMW, demonstrated the best mechanical performance compared to the reference concrete. After 28 days of curing, this sample exhibited a compressive strength (R_c) of 25 MPa. Furthermore, it demonstrated a tensile strength of 4.61 MPa and a dynamic modulus of elasticity of 44.39 GPa, with rebound values of 27 MPa. The slump of the specimens ranged from 5 cm to 9 cm, falling within the acceptable range of consistency (Class S2). Based on these findings, the OPCD_OPW (5) formulation is considered optimal for use in concrete production.

This research paper provides a valuable contribution to the management of OPA and OMW (OPA_OMW) generated from the olive processing industry, which is known to have significant negative environmental impacts. The paper presents an intriguing approach to recycling these materials for use in civil engineering applications.

In 1987, Campbell Soup Company introduced the Souper Combo, a line of frozen soup and sandwiches. Melvin Druin, vice‐president for packaging, called it “the perfect combination of old‐fashioned good taste and today's convenience. No mess. No fuss. Easy to use. All you have to do is clean your spoon. Everything else just throw away.” Unfortunately, the multi‐layered plastic‐coated packaging does not just disappear when thrown away. Plastics packaging, particularly from convenience products, has become a waste disposal nightmare. Garbage, an environmental magazine, gave the Souper Combo an “in the dumpster” award, saying, “It's precisely the kind of product that's created the municipal landfill monster.”

This paper offers a brief review of the present use of scanning electron microscopy (SEM) in concrete studies, from the perspective of how research in materials science is translated into applications in construction engineering. It describes the scope of present use of the method, and attempts a prospective for the near future in areas where more work could make productive use of the technology. Selected case studies have also been discussed. The electron microscope has been used as a research tool in understanding the root cause of the differing performance of various types of concrete under various conditions, a development tool in making better concrete, and a diagnosis tool on problems like cracking of concrete. The paper also explains how sample preparation affects the type and quality of information which the SEM can produce.

A systems perspective of waste management allows an integrated approach not only to the five basic functional elements of waste management itself (generation, reduction, collection, recycling, disposal), but to the problems arising at the interfaces with the management of energy, nature conservation, environmental protection, economic factors like unemployment and productivity, etc. This monograph separately describes present practices and the problems to be solved in each of the functional areas of waste management and at the important interfaces. Strategies for more efficient control are then proposed from a systems perspective. Systematic and objective means of solving problems become possible leading to optimal management and a positive contribution to economic development, not least through resource conservation. India is the particular context within which waste generation and management are discussed. In considering waste disposal techniques, special attention is given to sewage and radioactive wastes.