Search results

Electric motor heating during biomass recovery and its handling on conveyor is a serious concern for the motor performance. Thus, the purpose of this paper is to design and develop a hardware prototype of master–slave electric motors based biomass conveyor system to use the motors under normal operating conditions without overheating.

The hardware prototype of the system used master–slave electric motors for embedded controller operated robotic arm to automatically replace conveyor motors by one another. A mixed signal based embedded controller (C8051F226DK), fully compliant with IEEE 1149.1 specifications, was used to operate the entire system. A precise temperature measurement of motor with the help of negative temperature coefficient sensor was possible due to the utilization of industry standard temperature controller (N76E003AT20). Also, a pulse width modulation based speed control was achieved for master–slave motors of biomass conveyor.

As compared to conventional energy based mains supply, the system is self-sufficient to extract more energy from solar supply with an energy increase of 11.38%. With respect to conventional energy based \ of 47.31%, solar energy based higher energy saving of 52.69% was reported. Also, the work achieved higher temperature reduction of 34.26% of the motor as compared to previous cooling options.

The proposed technique is free from air, liquid and phase-changing material based cooling materials. As a consequence, the work prevents the wastage of these materials and does not cause the risk of health hazards. Also, the motors are used with their original dimensions without facing any leakage problems.

This paper aims to estimate the bearing capacity of a surface strip and circular footings lying on layered sand using numerical limit analysis.

Lower and upper bound limit analysis, as well as finite elements and second-order conic programming (SOCP), are used in this analysis. The yield criterion of Mohr-Coulomb is used to model soil behavior. Using this technique, stringent lower and upper bounds on ultimate bearing capacity can be achieved by assuming an associated flow law.

The obtained results indicate that the exact collapse load is typically being bracketed to within 6% about a mean of both the bounds. The obtained results are compared with the existing literature wherever applicable.

To the best of the authors’ knowledge, no study has used lower and upper bound limit analysis, as well as finite elements and SOCP, to estimate the bearing capacity of a surface strip and circular footings lying on layered sand.

This study aims to investigate the influence of two perceived organizational ethics systems (perceived ethics training quality and integrity-based climate) on the ethical decision-making (EDM) of tax accountants in Ghana. The study also examines the moderating role of the decision-makers’ financial situation on the quality ethics training–EDM relationship.

Survey data from 356 tax accountants were analyzed using the partial least squares structural equation modeling technique.

The results show that the two ethics systems influence EDM, but their extent of influence varies across the stages of EDM. Specifically, quality ethics training is a better predictor of EDM at the ethical issue recognition stage, whereas integrity-based climate is a better predictor of EDM at the ethical intention stage. The study also found that decision-makers’ financial situation predicts the ethical recognition stage of EDM but does not moderate the quality ethics training–EDM relationship.

This study recommends the concurrent deployment of quality ethics training and an integrity-based work climate to improve ethical behavior. Policymakers should also emphasize a work climate that promotes honesty, conscientiousness and ethical principles (integrity-based climate) to improve ethical intentions.

This study applied the interactionist theory by capturing the relative effects of two organizational ethics systems and an individual-level situational factor in a single model. To the best of the authors’ knowledge, this is the first study that tests the moderation effect of decision-makers’ financial situation on the ethics training–EDM relationship in a developing country context.

This paper aims to investigate how and when visual referents in brand visual aesthetics (i.e. colours, shapes, patterns and materials) serve as design applications that enable consumer diasporic identity.

This paper uses an innovative methodology that triangulates 58 in-depth interviews with diasporic consumers, 9 interviews with brand managers and designers and a visual analysis of brands (food retailer, spices and nuts, skincare, hair and cosmetics, ice cream and wine) to provide a view of the phenomenon from multiple perspectives.

This study illustrates how and when particular applications and compositions of product and design referents support diasporic identity for Middle Eastern consumers living outside the Middle East. Specifically, it illustrates how the design applications of harmonising (applying separate ancestral homeland and culture of living product and design referents simultaneously), homaging (departing from the culture of living product and design referents with a subtle tribute to ancestral homeland culture) and heritaging (departing from the ancestral homeland culture product and design referents with slight updates to a culture of living style) can enable diasporic identity in particular social situations.

Although applied to the Middle Eastern diaspora, this research opens up interesting avenues for future research that assesses diasporic consumers’ responses to brands seeking to use visual design to engage with this market. Moreover, future research should explore these design applications in relation to issues of cultural appreciation and appropriation.

The hybrid design compositions identified in this study can provide brand managers with practical tools for navigating the design process when targeting a diasporic segment. The design applications and their consequences are discussed while visually demonstrating how they can be crafted.

While previous research mainly focused on how consumption from the ancestral homeland occurred, to the best of the authors’ knowledge, this study is the first to examine how hybrid design compositions that combine a diaspora’s ancestral homeland culture and their culture of living simultaneously and to varying degrees resonate with diasporic consumers.

While uncertainty has always been a feature of the healthcare environment, its pace and scope are rapidly increasing, fueled by myriad factors such as technological advancements, the threat and frequency of disruptive events, global economic developments, and increasing complexity. Contemporary healthcare organizations thus persistently face what is known as “deep uncertainty,” which obscures their ability to predict outcomes of strategic action and decision-making, presenting them with novel challenges and threatening their survival. Persistent, deep uncertainty challenges us to revisit and reconsider how we think about uncertainty and the strategic actions needed by organizations to thrive under these circumstances. Simply put, how can healthcare organizations thrive in the face of deeply uncertain environments? We argue that healthcare organizations need to employ both adaptive and creative strategic approaches in order to effectively meet patients' needs and capture value in the long-term future. The chapter concludes by offering two ways organizations can build the dynamic capabilities needed to employ such approaches.

This paper aims to present an accurate magnetic equivalent circuit for modeling the cylindrical electromagnet so that by analyzing it, the magnetic flux density in different parts of the electromagnet, as well as its lifting force, can be calculated.

The structure of the electromagnet is divided into parts that can be modeled by lumped element parameters. Mathematical equations for calculating these elements are presented and proved. The axial symmetry of the cylindrical electromagnet made it possible to use planar circuits for its modeling. To increase the accuracy of the proposed equivalent circuit, attention has been paid to the leakage flux as well as the nonlinear behavior of the ferromagnetic core. Also, the curvature of the magnetic flux path is considered in the calculation of the corner permeances of the core.

The magnetic flux density in different parts of the electromagnet was calculated using nodal analysis of the circuit and compared to the results of the finite element method. Also, a test bed was established to measure the lifting force of the electromagnet. Comparing the results shows a difference of less than 3% which indicate the good accuracy of the proposed circuit. In addition, due to the curvature of the flux path, there is a no-flux region in the center of the disk, the extent of which depends on the thickness of the disk and the diameter of the middle leg.

Magnetic equivalent circuit is a new contribution to analyze the cylindrical electromagnet and calculate its lifting force with good accuracy. The circuit lumped elements can be quickly calculated using mathematical equations and software such as MATLAB according to the actual path of the magnetic flux. Compared to other methods, the proposed circuit analyzes the electromagnet in a shorter period of time. This is the most important advantage of the proposed circuit model.

Limited geometric accuracy is one of the major challenges that hinder the wider application of additive manufacturing (AM). This paper aims to predict in-plane shape deviation for online inspection and compensation to prevent error accumulation and improve shape fidelity in AM.

A sequence-to-sequence model with an attention mechanism (Seq2Seq+Attention) is proposed and implemented to predict subsequent layers or the occluded toolpath deviations after the multiresolution alignment. A shape compensation plan can be performed for the large deviation predicted.

The proposed Seq2Seq+Attention model is able to provide consistent prediction accuracy. The compensation plan proposed based on the predicted deviation can significantly improve the printing fidelity for those layers detected with large deviations.

Based on the experiments conducted on the knee joint samples, the proposed method outperforms the other three machine learning methods for both subsequent layer and occluded toolpath deviation prediction.

This work fills a research gap for predicting in-plane deviation not only for subsequent layers but also for occluded paths due to the missing scanning measurements. It is also combined with the multiresolution alignment and change point detection to determine the necessity of a compensation plan with updated G-code.

How do dark personality traits impact workplace bullying (WB)? How can organizations mitigate it? This study aims to explore the relationship between the Dark Tetrad (DT) (narcissism, psychopathy [PY], Machiavellianism and sadism [SM]) and WB, proposing the mediation role of moral disengagement (MD) and the moderation role of emotional stability (ES).

The proposed mediated-moderation model was tested on 404 employees working in the hospitality sector in Pakistan. Data have been analyzed through regression analysis and PROCESS macros to test the study’s hypotheses.

PY, Machiavellianism and SM positively relate to WB and MD mediates this relationship. A high level of ES reduces the intensity of the mediated influence of PY, Machiavellianism and SM on WB.

Developing targeted policies and practices (e.g. personality tests to build a good psychological architecture of the firm) and reviewing processes that support the moral justification of antisocial conduct can be beneficial for limiting WB. In addition, meditation, mindfulness training and supporting trust and cooperation within organizations can increase the mitigating effect of ES and, in turn, reduce WB.

To the best of the authors’ knowledge, this is the first study that explicitly verifies a mediated-moderation model on DT-WB while proposing a further explanation (i.e. mediation of MD) and a novel solution (i.e., moderation by ES).

This study aims to conduct a thorough literature review to map current studies on international marketing capabilities (IMCs) applying dynamic capabilities view (DCV). The aim of this study is to increase the chances for more conceptual and terminological rigor in future research in this particular research area.

This is a systematic literature review following the established review process of reviews in leading (international) marketing journals. A multilevel analytical approach was adopted, combining inductive coding with deductive coding and following the logic of antecedents-phenomena-consequences.

Synthesis of 20 rigorously selected previous empirical studies on IMCs applying DCV reveals that academic interest in these capabilities is well justified and growing and there are some well researched antecedents to focal capabilities (e.g. inter-organizational capabilities, outside-in market orientation) as well as their prevalent consequences (e.g. export and innovation performance). There is little knowledge of moderators to these links, especially with regard to consequences. This review illustrates that the current research lacks consistency in how key constructs are defined and measured, provides the guide to future conceptualization and measurement of so-called International Dynamic Marketing Capabilities (IDMCs) and proposes some concrete research directions.

The authors extend prior research in the investigated topic by critically evaluating prior works, providing improved conceptualization of IDMCs as well as concrete research agenda for IDMCs structured along recommendations for Theory, Context and Methods (TCM framework).

Gas metal arc-based directed energy deposition (GMA-DED) process experiences residual stress (RS) developed due to heat accumulation during successive layer deposition as a significant challenge. To address that, monitoring of transient temperature distribution concerning time is a critical input. Finite element analysis (FEA) is considered a decisive engineering tool in quantifying temperature and RS in all manufacturing processes. However, computational time and prediction accuracy has always been a matter of concern for FEA-based prediction of responses in the GMA-DED process. Therefore, this study aims to investigate the effect of finite element mesh variations on the developed RS in the GMA-DED process.

The variation in the element shape functions, i.e. linear- and quadratic-interpolation elements, has been used to model a single-track 10-layered thin-walled component in Ansys parametric design language. Two cases have been proposed in this study: Case 1 has been meshed with the linear-interpolation elements and Case 2 has been meshed with the combination of linear- and quadratic-interpolation elements. Furthermore, the modelled responses are authenticated with the experimental results measured through the data acquisition system for temperature and RS.

A good agreement of temperature and RS profile has been observed between predicted and experimental values. Considering similar parameters, Case 1 produced an average error of 4.13%, whereas Case 2 produced an average error of 23.45% in temperature prediction. Besides, comparing the longitudinal stress in the transverse direction for Cases 1 and 2 produced an error of 8.282% and 12.796%, respectively.

To avoid the costly and time-taking experimental approach, the experts have suggested the utilization of numerical methods in the design optimization of engineering problems. The FEA approach, however, is a subtle tool, still, it faces high computational cost and low accuracy based on the choice of selected element technology. This research can serve as a basis for the choice of element technology which can predict better responses in the thermo-mechanical modelling of the GMA-DED process.