Search results

The purpose of this paper is to study the effect of temperature on Zn–Ni alloys in ChCl–Urea.

Based on cyclic voltammetry experiments, the deposition behavior and kinetics of the Zn–Ni alloy are studied. The nucleation process of the Zn–Ni alloy is studied in detail via chronoamperometry experiments. The effects of the deposition temperature on the microstructure, Ni content and phase composition of Zn–Ni alloy coatings are investigated via scanning electron microscopy and X-ray diffraction (XRD) combined with classical thermodynamics.

The results show that with increasing temperature, the reduction peak shifts toward a more positive electric potential, which is beneficial for the co-electric deposition process, and the diffusion coefficient is estimated. With increasing temperature, the nucleation process of the Zn–Ni alloy becomes a three-dimensional instantaneous nucleation, the typical kinetic parameters are determined using the standard 3D growth proliferation control model and the Gibbs free energy is estimated. The Zn–Ni alloy coatings are prepared via normal co-deposition. With increasing temperature, the degree of crystallinity increases, the coating gradually becomes uniform and compact and the XRD peak intensity increases.

The nucleation process of the Zn–Ni alloy at different temperatures is analyzed. The diffusion coefficient D and Gibbs free energy are calculated. The contribution of the three processes at different temperatures is analyzed. The effect of temperature on the morphology of the Zn–Ni alloy coatings is studied.

The purpose of this study is to reveal the effect of nano-Al₂O₃ particle addition on the nucleation/growth kinetics, microhardness, wear resistance and corrosion resistance of Co–P–xAl₂O₃ nanocomposite plating.

The kinetics and properties of Co–P–xAl₂O₃ nanocomposite plating prepared by electroplating were investigated by electrochemical measurements, scanning electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, Vickers microhardness measurement, SRV5 friction and wear tester and atomic force microscopy.

A 12 g/L nano-Al₂O₃ addition in the plating solution can transform the nucleation/growth kinetics of the plating from the 3D progressive model to the 3D instantaneous model. The microhardness of the plating increased with the increase of nano-Al₂O₃ content in plating. The wear resistance of the plating did not adhere strictly to Archard’s law. An even and denser corrosion product film was generated due to the finer grains, with a high corrosion resistance.

The effect of different nano-Al₂O₃ addition on the nucleation/growth kinetics and properties of Co–P–xAl₂O₃ nanocomposite plating was investigated, and an anticorrosion mechanism of Co–P–xAl₂O₃ nanocomposite plating was proposed.

The purpose of this study is determination of cadmium using silver-gold bimetallic nanoparticles (Ag-Au BMNPs) and an aptamer modified glassy carbon electrode.

The maximum response of modified electrode was obtained with, 50 mV pulse amplitude, 20 mV/s scan rate in phosphate buffer of pH 4.0. Ag-Au BMNPs, as the mediators improved electron transmit during the entire electron transfer process and the aptasensor response. Herein, the authors used aptamer as the capture probe to prepare an aptasensor with enhanced stability.

The proposed aptasensor exhibited a wide linearity to cadmium in the range of 0.001–0.100 µg/L with a low detection limit of 0.005×10⁻³ µg/L. The glassy carbon electrodes with Ag-Au BMNPs showed a lower detection limit.

This aptasensor has good reproducibility, stability and repeatability and is cost-effective to regenerate. The specificity and selectivity of the novel modified electrode is tested in the presence of other interfering metal ions such as Fe²⁺, Mn²⁺, Mg²⁺, Sb³⁺ and Bi³⁺. The aptasensor shows 10 times more sensitivity and selectivity for Cd²⁺ ions.