Search results

This paper provides a summary of the issues in the passive fire protection of steel structures. Types of passive fire protection and the material properties of protection members and steel members are described. The paper deals with the possibility of partial fire protection for secondary steel beams, in cases where, due to possible membrane action, it is not necessary to apply passive protection to the entire beams.

Studies of partially fire-protected steel structures are compared, and results from studies with different input data are summarized. A fire experiment was conducted to investigate the effect of partial passive protection in a small-scale furnace. Based on the findings of the experiment, numerical models were prepared using Ansys Mechanical.

The results are summarized, and a partial fire protection length of 500 mm is recommended. Various partial fire protection lengths were compared, and the temperature development of the steel contactors was compared using a protection length of 500 mm. At the end of the paper, options for partial passive protection of steel beams are presented.

Extended paper from ASFE2021 based on selection.

This paper aims to compare the wear behavior, surface roughness, friction coefficient and volume loss of high-velocity oxy-fuel (HVOF) sprayed WC–Co and WC–Cr₃C₂–Ni coatings on AISI 1095 steel with spraying times of 10 and 15 s.

In this study, the pin-on-disc testing technique was used to evaluate the wear characteristics at a speed of 0.24 m/s, load of 40 N and test time of 60 min under dry conditions at room temperature. The wear characteristics were examined and analyzed by scanning electron microscopy and energy dispersive X-ray spectroscopy. The surface roughness of a coated surface was measured, and microhardness measurements were performed on the cross-sectioned and polished surfaces of the coating.

Spraying time and powder material affected the hardness of HVOF coatings due to differences in the porosity of the coated layers. The average hardness of the WC–Cr₃C₂–Ni coating with a spaying time of 15 s was approximately 14% higher than that of the WC–Cr₃C₂–Ni coating with a spraying time of 10 s. Under an applied load of 40 N, the WC–Co coating with a spraying time of 15 s had the lowest variation in the friction coefficient compared with the other coatings. The WC–Co coating with a spraying time of 10 s had the lowest average and variation in volume loss compared to the other coatings. The WC–Cr₃C₂–Ni coating with a spraying time of 10 s exhibited the highest average volume loss. The wear features changed slightly with the spraying time owing to variations in the hardness and friction coefficient.

This study investigated tribological performance of WC–Co; WC-Cr₃C₂-Ni coatings with spraying times of 10 and 15 s using pin-on-disc tribometer by rotating the relatively soft pin (C45 steel) against hard coated substrate (disc).

The aim of this paper is to determine the thermal conductivity of a protective layer of alkali-activated cement and the possibility of performing fire protection with fireclay sand and Lightweight mortar. Unprotected steel structures have generally low fire resistance and require surface protection. The design of passive protection of a steel element must consider the service life of the structure and the possible need to replace the fire protection layer. Currently, conventional passive protection options include intumescent coatings, which are subject to frequent inspection and renewal, gypsum and cement-based fire coatings and gypsum and cement board fire protection.

Alkali-activated cements provide an alternative to traditional Portland clinker-based materials for specific areas. This paper presents the properties of hybrid cement, its manufacturability for conventional mortars and the development of passive fire protection. Fire experiments were conducted with mortar with alkali-activated and fireclay sand and lightweight mortar with alkali-activated cement and expanded perlite. Fire experiment FE modelling.

The temperatures of the protected steel and the formation of cracks in the protective layer were investigated. Based on the experiments, the thermal conductivities of the two protective layers were determined. Conclusions are presented on the applicability of alkaline-activated cement mortars and the possibilities of applicability for the protection of steel structures. The functionality of the passive fire layer was confirmed and the strengths of the mortar used were determined. The use of alkali-activated cements was shown to be a suitable option for sustainable passive fire protection of steel structures.

Eco-friendly fire protection based on hybrid alkali-activated cement of steel members.

First, the effect of magnetic field intensity and nano-ferrofluid concentrations on surface roughness was evaluated in magnetic minimum quantity lubrication (MMQL). Then, the effect of lubricant flow rate and nozzle position on surface roughness was investigated in MQL, MMQL, electrostatic MQL (EMQL) and electromagnetic MQL (EMMQL).

This study examined the performance of MQL under magnetic and electric fields in turning AISI 304 stainless steel in terms of surface roughness and compared the results with those obtained from wet cutting and MQL turning operations. To prepare the nano-ferrofluid used in different states of MQL, Fe₃O₄ nanoparticles were added to the base fluid.

The results showed that the surface roughness under the EMMQL technique decreased by 36% and 49.4% on average compared with wet and MQL techniques, respectively. The lubrication technique affected the surface roughness by 90.2%, whereas it was 8.3% for the lubricant flow rate. EMQL and EMMQL techniques had no significant difference in their effects on surface roughness. In the innovative MMQL technique, the nano-ferrofluid concentration of 6% and magnetic field intensity of 93 G resulted in lower surface roughness of the workpiece relative to other counterparts.

Examining previously published studies showed that using nano-ferrofluids under a magnetic field for cooling purposes in machining processes have less considered by researchers. This study applies an innovative method of lubrication under the concurrent effect of magnetic and electric fields, called EMMQL, to improve the efficiency of MQL in machining hard-to-cut materials. For comprehensively inspecting the newly presented method, the effects of several parameters, including the nano-ferrofluid concentration, magnetic field intensity, lubricant flow rate and position of lubricant spray nozzle, on the surface roughness of workpiece in turning of AISI 304 stainless steel are investigated.

Intumescent coatings are nowadays a dominant passive system used to protect structural materials in case of fire. Due to their reactive swelling behaviour, intumescent coatings are particularly complex materials to be modelled and predicted, which can be extremely useful especially for performance-based fire safety designs. In addition, many parameters influence their performance, and this challenges the definition and quantification of their material properties. Several approaches and models of various complexities are proposed in the literature, and they are reviewed and analysed in a critical literature review.

Analytical, finite-difference and finite-element methods for modelling intumescent coatings are compared, followed by the definition and quantification of the main physical, thermal, and optical properties of intumescent coatings: swelled thickness, thermal conductivity and resistance, density, specific heat capacity, and emissivity/absorptivity.

The study highlights the scarce consideration of key influencing factors on the material properties, and the tendency to simplify the problem into effective thermo-physical properties, such as effective thermal conductivity. As a conclusion, the literature review underlines the lack of homogenisation of modelling approaches and material properties, as well as the need for a universal modelling method that can generally simulate the performance of intumescent coatings, combine the large amount of published experimental data, and reliably produce fire-safe performance-based designs.

Due to their limited applicability, high complexity and little comparability, the presented literature review does not focus on analysing and comparing different multi-component models, constituted of many model-specific input parameters. On the contrary, the presented literature review compares various approaches, models and thermo-physical properties which primarily focusses on solving the heat transfer problem through swelling intumescent systems.

The presented literature review analyses and discusses the various modelling approaches to describe and predict the behaviour of swelling intumescent coatings as fire protection for structural materials. Due to the vast variety of available commercial products and potential testing conditions, these data are rarely compared and combined to achieve an overall understanding on the response of intumescent coatings as fire protection measure. The study highlights the lack of information and homogenisation of various modelling approaches, and it underlines the research needs about several aspects related to the intumescent coating behaviour modelling, also providing some useful suggestions for future studies.

This study aims to explore the synergistic effect of oxide nanoparticles (ZnO, Fe₂O₃, SiO₂) and cerium nitrate inhibitor on anti-corrosion performance of epoxy coating. First, cerium nitrate inhibitors are absorbed on the surface of various oxide nanoparticles. Thereafter, epoxy nanocomposite coatings have been fabricated on carbon steel substrate using these oxide@Ce nanoparticles as both nano-fillers and nano-inhibitors.

To evaluate the impact of oxides@Ce nanoparticles on mechanical properties of epoxy coating, the abrasion resistance and impact resistance of epoxy coatings have been examined. To study the impact of oxides@Ce nanoparticles on anti-corrosion performance of epoxy coating for steel, the electrochemical impedance spectroscopy has been carried out in 3% NaCl solution.

ZnO@Ce3+ and SiO2@Ce3+ nanoparticles provide more enhancement in the epoxy pore network than modification of the epoxy/steel interface. Whereas, Fe2O3@Ce3+ nanoparticles have more to do with modification of the epoxy/steel interface than to change the epoxy pore network.

Incorporation of both oxide nanoparticles and inorganic inhibitor into the epoxy resin is a promising approach for enhancing the anti-corrosion performance of carbon steel.

Thermal protection of a flange is critical for preventing tower icing and collapse of wind turbines (WTs) in extremely cold weather. This study aims to develop a novel thermal protection system for the WTs flanges using an electrical heat-tracing element.

A three-dimensional model and the Poly-Hexacore mesh structure are used, and the fluid-solid coupling method was validated and then deployed to analyze the heat transfer and convection process. Intra-volumetric heat sources are applied to represent the heat generated by the heating element, and the dynamic boundary conditions are considered. The steady temperature and temperature uniformity of the flange are the assessment criteria for the thermal protection performance of the heating element.

Enlarging the heating area and increasing the heating power improved the flange's temperature and temperature uniformity. A heating power of 4.9 kW was suitable for engineering applications with the lowest temperature nonuniformity. Compared with continuous heating, the increased temperature nonuniformity was buffered, and the electrical power consumption was reduced by half using pulse heating. Pulse heating time intervals of 1, 3 and 4 h were determined for the spring, autumn and winter, respectively.

The originality of this study is to propose a novel electrical heat-tracing thermal protection system for the WTs flanges. The effect of different arrangements, heating powers and heating strategies was studied, by which the theoretical basis is provided for a stable and long-term utilization of the WT flange.

The purpose of this paper is to study the effect of surface salt spray duration on the fretting wear and electrochemical corrosion behaviors of Inconel 690 alloy.

A high-temperature steam generator was applied to salt spray test samples, a fretting wear rig was used to realize the damage behavior tests, an electrochemical workstation was applied to analysis the changes of each sample’s corrosion dynamic response before and after fretting wear.

The thickness of the oxide film that formed on sample surface was increased with the salt spray duration, and somewhat it could act as lubrication during the fretting wear process; however, the corrosive chloride would accelerate the fretting mechanical damage behavior.

In a salt steam spray condition, the fretting tribo-corrosion behaviors of Inconel 690 alloy surface was studied.

This study aims to form composite solid lubricant coatings on the surface of bearing steel, which can significantly improve the tribological properties of thrust cylindrical roller bearings (TCRBs). Phosphating films possess microscopic porosity that typically needs to be sealed with oil, grease or wax. Due to its unique crystal structure, the phosphating film itself also exhibits a certain degree of lubricity. In this study, solid lubricants are used to fill the pores of the phosphating film. By combining the phosphating film with solid lubricants, lubrication and wear reduction can be achieved.

In this study, the surfaces of the shaft washer (WS) and seat washer (GS) were treated with zinc-phosphating. Subsequently, a solid lubricant solution (polytetrafluoroethylene [PTFE], MoS₂ and graphite) was sprayed onto the phosphated samples at concentrations of 1 , 2  and 3 g/L. The porous and adsorptive nature of the phosphating film was used to embed the solid lubricant particles into the film, thus forming a composite lubrication layer containing solid lubricants on the surface of the bearing steel.

The addition of solid lubricant materials has shown significant potential in reducing wear losses compared with phosphated samples without such additives. Increasing the amount of solid lubricant added can facilitate the formation of a transfer film, which further enhances the protective properties. However, it is important to note that excessive amounts of solid lubricant material can contribute to seizure, leading to increased wear losses of the cage and a higher average coefficient of friction (ACOF).By spraying a PTFE solution with a concentration of 2 g/L, the lowest ACOF and cage wear loss were achieved, resulting in reductions of 60.5% for the ACOF and 89.4% for the cage wear loss. Similarly, when spraying a graphite solution with a concentration of 3 g/L, the lowest wear losses for GS and WS were observed, with reductions of 51.7% for GS wear loss and 38.9% for WS wear loss.

The combination of the phosphating film and solid lubricants aims to achieve lubrication and wear reduction, providing a new approach to wear-resistant technology for TCRBs.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-07-2023-0231/

Due to the harsh underground environment in coal mining, the surface of hydraulic support columns corrodes severely, resulting in significant economic losses. Therefore, a highly corrosion-resistant coatings is needed to extend the service life of the columns.

This study aims to compare the corrosion resistance of ST-Cr₃C₂-NiCr (sealed treatment Cr₃C₂-NiCr) coatings with industrially applied chromium plating. The corrosion failure mechanism of the coatings was investigated.

The results demonstrated that the ST-Cr₃C₂-NiCr coatings exhibited excellent corrosion resistance. After sealing treatment, the corrosion potential of Cr₃C₂-NiCr coatings was −0.215 V, and the corrosion current density of Cr₃C₂-NiCr coatings was lower than that of the plated parts.

ST-Cr₃C₂-NiCr coatings prepared by supersonic atmospheric plasma spraying could provide excellent corrosion resistance in the coal industry.

The low porosity and the presence of the NiCr phase were crucial factors contributing to the preferable corrosion resistance exhibited by the ST-Cr₃C₂-NiCr coatings. The corrosive process of the coatings involved layer-by-layer delamination of surface oxide film, sub-surface pitting, formation and degradation of sub-surface passive film, as well as severe block-like delamination.