Search results

This paper aims to investigate the corrosion kinetics and corrosion behavior of NdFeB magnets with the addition of heavy rare earth dysprosium (Dy) for its inhibitory activity on poor corrosion resistance of NdFeB magnets.

To study the effect of dysprosium addition on corrosion behavior of NdFeB magnets and investigate its mechanism, potentiodynamic polarization, scanning electron microscopy (SEM), electrochemical impedance, energy dispersion spectrum (EDS) and scanning Kelvin probe force microscopy (SKPFM) were applied in the research. Besides, microstructures were observed by SEM equipped with EDS. Atomic force microscopy was introduced to analyze the morphology, potential image as well as the contact potential difference. The SKPFM mapping scan was applied to obtain the contact potential around Nd-rich phase at 0.1 Hz. The magnets were detected via X-ray diffraction.

Substitution of Nd with Dy led to improvement of corrosion resistance and reduced the potential difference between matrix and Nd-rich phase. Corrosion resistance is Nd-rich phase < the void < metal matrix; maximum potential difference between matrix and Nd-rich phase of Dy = 0, Dy = 3 and Dy = 6 Wt.% is 411.3, 279.4 and 255.8 mV, respectively. The corrosion rate of NdFeB magnet with 6 Wt.% Dy is about 67% of that without Dy at steady corrosion stage. The addition of Dy markedly enhanced the corrosion resistance of NdFeB magnets.

This research innovatively investigates the effect of adding heavy rare earth Dy to NdFeB permanent magnets on magnetic properties, as well as their effects on microstructure, phase structure and most importantly on corrosion resistance. Most scholars are studying the effect of element addition on magnetic properties but not on corrosion resistance. This paper creatively fills this research gap. NdFeB magnets are applied in smart cars, robotics, AI intelligence, etc. The in-depth research on corrosion resistance by adding heavy rare earths has made significant and outstanding contributions to promoting the rapid development of the rare earth industry.

The principle of infinite life design currently directs fatigue resistance strategies for metro car bodies. However, this principle might not fully account for the dynamic influence of operational loads and the inevitable presence of defects. This study aims to integrate methods of service life estimation and residual life assessment, which are based on operational loads, into the existing infinite life verification framework to further ensure the operational safety of subway trains.

Operational loads and fatigue loading spectra were determined through the field test. The material test was conducted to investigate characteristics of the fracture toughness and the crack growth rate. The fatigue strength of the metro car body was first verified using the finite element method and Moore–Kommers–Japer diagrams. The service life was then estimated by applying the Miner rule and high-cycle fatigue curves in a modified form of the Basquin equation. Finally, the residual life was assessed utilizing a fracture assessment diagram and a fitted curve of crack growth rate adhered to the Paris formula.

Neither the maximum utilization factor nor the cumulative damage exceeds the threshold value of 1.0, the metro car body could meet the design life requirement of 30 years or 6.6 million km. However, three out of five fatigue key points were significantly influenced by the operational loads, which indicates that a single fatigue strength verification cannot achieve the infinite life design objective of the metro car body. For a projected design life of 30 years, the tolerance depth is 12.2 mm, which can underscore a relatively robust damage tolerance capability.

The influence of operational loads on fatigue life was presented by the discrepancy analysis between fatigue strength verification results and service life estimation results. The fracture properties of butt-welded joints were tested and used for the damage tolerance assessment. The damage tolerance life can be effectively related by a newly developed equation in this study. It can be a valuable tool to provide the theoretical guidance and technical support for the structural improvements and maintenance decisions of the metro car body.

For the purpose of saving nickel, this study aims to develop new duplex stainless steel cored wires suitable for wire arc additive manufacturing (WAAM) with the addition of nitrogen.

The effect of nitrogen content on the microstructure and mechanical properties of the thin-walled deposits is investigated in detail.

The microstructure of thin-walled deposits mainly consists of austenite, ferrite and secondary austenite. With increasing nitrogen content, the austenite in the deposited metals increases. The austenite proportion in the bottom region is more than that in the top region of the deposited metals. The χ phase is randomly distributed at the grain boundaries and within ferrite. The σ phase is mainly precipitated at ferrite and austenite grain boundaries. With increasing nitrogen content, the tensile strength of the deposited metals increases, but the impact toughness of the deposited metals deteriorates.

This study proposes new duplex stainless steel cored wires for WAAM, which realizes the objective of saving nickel.

Powder bed fusion-laser beam (PBF-LB) is a rapidly growing manufacturing technology for producing Al-Si alloys. This technology can be used to produce high-pressure die-casting (HPDC) prototypes. The purpose of this paper is to understand the similarities and differences in the microstructures and properties of PBF-LB and HPDC alloys.

PBF-LB AlSi10Mg and HPDC AlSi10Mn plates with different thicknesses were manufactured. Iso-thermal heat treatment was conducted on PBF-LB bending plates. A detailed meso-micro-nanostructure analysis was performed. Tensile, bending and microhardness tests were conducted on both alloys.

The PBF-LB skin was highly textured and softer than its core, opposite to what is observed in the HPDC alloy. Increasing sample thickness increased the bulk strength for the PBF-LB alloy, contrasting with the decrease for the HPDC alloy. In addition, the tolerance to fracture initiation during bending deformation is greater for the HPDC material, probably due to its stronger skin region.

This knowledge is crucial to understand how geometry of parts may affect the properties of PBF-LB components. In particular, understanding the role of geometry is important when using PBF-LB as a HPDC prototype.

This is the first comprehensive meso-micro-nanostructure comparison of both PBF-LB and HPDC alloys from the millimetre to nanometre scale reported to date that also considers variations in the skin versus core microstructure and mechanical properties.