Search results

The increasing demands of high-speed railway transportation aggravate the wheel and rail surface wear. It is of great significance to repair the worn wheel timely by predicting the wheel and rail surface wear, which will improve both the service life of the wheel and rail and the safe operation of the train. The purpose of this study is to propose a new prediction method of wheel tread wear, which can provide some reference for selecting proper re-profiling period of wheel.

The standard and worn wheel profiles were first matched with the standard 60N rail profile, and then the wheel/rail finite element models (FEMs) were established for elastic-plastic contact calculation. A calculation method of the friction work was proposed based on contact analysis. Afterwards, a simplified method for calculating wheel tread wear was presented and the wear with different running mileages was predicted.

The wheel tread wear increased the relative displacement and friction of contact spots. There was obvious fluctuation in the wheel tread friction work curve of the worn model. The wear patterns predicted in the present study were in accordance with the actual situation, especially in the worn model.

In summary, the simplified method based on FEM presented in this paper could effectively calculate wheel tread wear and predict the wear patterns. It would provide valuable clews for the wheel repair work.

The serious wear problem of heavy-haul freight vehicle wheels affects the safety and economy of vehicle operation. This paper aims to study wheel wear evolution law and the influence of line parameters on wheel wear of heavy-haul freight, and provide the basis for operation and line maintenance.

The wheel wear test data of heavy-haul freight vehicles were analyzed. Then a heavy-haul freight vehicle dynamic model was established. The line parameters influencing wheel wear in heavy-haul freight vehicles were also analyzed by the Jendel wear model, and the effects of rail cant, rail gauge, rail profile and line ramp on wheel wear were analyzed.

A rail cant of 1:40 results in less wheel wear; an increase in the rail gauge can reduce wheel wear; and when matched with the CHN60 rail, the wear depth is relatively small. A decrease of 9.21% in wheel wear depth when matched with the CHN60 rail profile. The ramp of the heavy-haul line is necessary to consider for calculating wheel wear. When the ramp is considered, the wear depth increases by 8.47%. The larger the ramp, the greater the braking force and therefore, the greater of the wheel wear.

This paper first summarizes the wear characteristics of wheels in heavy-haul freight vehicles and then systematically analyzes the effect of line parameters on wheel wear. In particular, this study researched the effects of rail cant, rail gauge, rail profile and line ramp on wheel wear.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-02-2024-0038/

The aim of this study is to calculate the coefficient of friction of wheel/rail interface in both water lubrication and dry friction conditions.

Specimens taken from wheel and rail used in railway transport were exposed to pin‐on‐disc wear testing with 10, 20, 30 and 40 N loads. The disc took the place of the rail and the pin that of the wheel in wear tests, and rain water was fed to the disc/pin interface with a three drops/min speed in wet friction conditions. The coefficient of friction and weight loss values of specimens were determined and types of wear mechanism were characterized.

It was observed that the friction coefficient decreased in wet sliding experiments, so smaller values were calculated in wet friction conditions than those of dry friction conditions for wheel specimens. However, this decrease was more drastic for rail specimens. Weight and volumetric loss values of rail materials were lower than those of wheel samples.

This study investigates the wet and dry sliding wear characteristics of train wheel‐rail materials.

The CL60 steel wheels of subway vehicles operating on specific lines require frequent refurbishment due to rapid wear and tear. Considering this issue, MoS₂-based and graphite-based solid lubricants are used to reduce the wear rate of subway wheels and extend their service life.

Under laboratory conditions, the effect of MoS₂-based and graphite-based solid lubricants on the friction and wear performance of subway wheels and rails was evaluated using a modified GPM-60 wear testing machine.

Under laboratory conditions, MoS₂-based solid lubricants have the best effect in reducing wheel/rail wear, compared to the control group without lubrication, at 2 × 105 revolutions, the total wheel-rail wear decreased by 95.07%. However, when three types of solid lubricants are used separately, the hardness evolution of the wheel-rail contact surface exhibits different characteristics.

The research results provide important support for improving the lifespan of wheel and rail, extending the service cycle of wheel and rail, reducing the operating costs of subway systems, improving the safety of subway systems and providing wear reduction maintenance for other high wear mechanical components.

The experiment was conducted through the design and modification of a GPM-60 testing machine for wear testing. The experiment simulated the wheel-rail contact situation under actual subway operation and evaluated the effects of three different solid lubricants, MoS₂-based and graphite-based, on the wear performance and surface hardening evolution of subway wheel-rail.

The purpose of this study is to match appropriate friction coefficients for subway operational vehicles, considering the dynamic variations of wheel profile wear.

This study combines experimental testing and numerical simulation to investigate the influence of wheel profile wear coupled with the friction coefficient on the vehicle dynamic response.

For the test route in this paper, it is recommended to control the friction coefficient on straight sections between 0.25 and 0.3, and on curved sections between 0.2 and 0.3. This satisfies the required adhesion coefficient for normal train traction and braking, while also ensuring the straight running performance and curve negotiation performance of the vehicle.

Reasonable friction coefficient ranges are proposed for straight and curved track lines to improve the operational safety and economy of the vehicles. Moreover, this study can provide a theoretical basis and reference direction for developing anti-wear measures for rail vehicles operating on fixed routes.

Considering the wear characteristics of operating vehicles and the dynamic changes in the wear profile, this paper explores the adaptability of different degrees of wheel wear profiles to different friction coefficients. Based on the response characteristics of vehicle dynamics, reasonable lubrication recommendations are proposed for this operating vehicle.

Metro wheels running on different lines can undergo wear at different positions. This paper aims to investigate the effects of wheel wear at two typical positions, i.e. wheel flange and tread, on the dynamic performance of metro vehicles and analyzes the differences, with an aim of providing theoretical support on wheel reprofiling for different metro lines.

Wheel profile data were measured on two actual metro lines, denoted A and B. It was observed that wheel wear on Lines A and B was concentrated on flanges and treads, respectively. A metro vehicle dynamics model was built using multibody dynamics software SIMPACK. Then it was applied to analyze the differences in effects of wheel wear at different positions on vehicle dynamic performance (VDP) for various speeds (50, 60 and 70 km/h) and line conditions (straight line, R1000m, R600m and R300m curves). Critical speed and vibration acceleration were used as indicators of VDP during linear motion (on straight track), while VDP during curvilinear motion (on curved track) was evaluated in terms of wheel/rail lateral force, wheel/rail vertical force, derailment coefficient and wheel unloading rate.

First, compared to wheel profile with tread wear, wheel profile with flange wear showed better performance during linear motion. When the distance traveled reached 8 × 104 and 14 × 104 km, the vehicle’s critical speed was 12.2 and 21.6% higher, respectively. The corresponding vertical and lateral vibration accelerations were 59.7 and 74.8% lower. Second, compared to wheel profile with flange wear, that with tread wear showed better performance during curvilinear motion, with smaller wheel/rail lateral force, derailment coefficient and wheel unloading rate. When the vehicle speed was 50, 60 and 70 km/h, the maximum difference in the three indicators between the two wheel profiles was 40.2, 44.7 and 23.1%, respectively. For R1000m, R600m and R300m curves, the corresponding maximum difference was 45.7, 69.0 and 44.4%, respectively.

The results of the study can provide a guidance and theoretical support on wheel reprofiling for different metro lines. On lines with large proportions of curved sections, metro vehicles are more prone to wheel flange wear and have poorer dynamic performance during curvilinear motion. Therefore, more attention should be paid to flange lubrication and maintenance for such lines. On lines with higher proportions of straight sections, metro vehicles are more prone to tread wear and have poorer performance on straight sections. So, tread maintenance and service requires more attention for such lines.

Existing research has focused primarily on the effects of wheel wear on VDP, but fails to consider the differences in the effects of wheel wear at different positions on VDP. In actual metro operation, the position of wheel wear can vary significantly between lines. Based on measured positions of wheel wear, this paper examines the differences in the effects of wheel wear at two typical positions, i.e. tread and flange, on VDP in detail.

While the normal wheel–rail contact model cannot be accurately used for light rail transit (LRT) wheel wear analysis with large wheelset lateral displacement and wheelset yaw angle, a modified semi-Hertzian contact model (MSHM) is proposed in the paper.

MSHM was first proposed to consider the wheelset motion with the lateral displacement and the yaw angle. Then, a dynamic model of an LRT was established and the influence of some key factors on wheel wear is analyzed. At last, after operating for a certain mileage, the predicted wheel wear is compared with the tested wheel wear.

Compared with the tested wheel wear, the predicted wheel wear shows a good agreement with the measured result, verifying the accuracy of MSHM.

Considering larger wheelset lateral displacement and yaw angle, MSHM can be used to calculate the wheel wear of the LRT with high accuracy.

In order to systematically grasp the changes and matching characteristics of wheel and rail profiles of high speed railway (HSR) in China, 172 rail profile measurement points and 384 wheels of 6 high-speed electric motive unites (EMUs) were selected on 6 typical HSR lines, including Beijing–Shanghai, Wuhan–Guangzhou, Harbin–Dalian, Lanzhou–Xinjiang, Guiyang–Guangzhou and Dandong–Dalian for a two-year field test.

Based on the measured data, the characteristics of rail and wheel wear were analyzed by mathematical statistics method. The equivalent conicity of wheel and rail matching in a wheel reprofiling cycle was analyzed by using the measured rail profile.

Results showed that when the curve radius of HSR was larger than 2,495 m, the wear rate of straight line and curve rail was almost the same. For the line with annual traffic gross weight less than 11 Mt, the vertical wear of rail was less than 0.01 mm. The wear rate of the rail with the curve radius less than 800 m increased obviously. The wheel tread wear of EMUs on Harbin–Dalian line, Lanzhou–Xinjiang line and Dandong–Dalian line was relatively large, and the average wear rate of tread was about 0.05–0.06 mm·(10,000 km)⁻¹, while that of Beijing–Shanghai line, Wuhan–Guangzhou line and Guiyang–Guangzhou line was about 0.03–0.035 mm·(10,000 km)⁻¹. When the wear range was small, the equivalent conicity increased with the increase of wheel tread wear. When the wear range of wheel was wide, the wheel–rail contact points were evenly distributed, and the equivalent conicity did not increase obviously.

This research proposes the distribution range of the equivalent conicity in one reprofiling cycle of various EMU trains, which provides guidance for the condition-based wheel reprofiling.

The purpose of this paper is to study the wear evolution of metro wheels under the conditions of different track sequences, track composition and vehicle load and then to predict wheel wear and to guide its maintenance.

By using the SIMPACK and MATLAB software, numerical simulation analysis of metro wheel wear is carried out based on Hertz theory, the FASTSIM algorithm and the Archard model. First of all, the vehicle dynamics model is established to calculate the motion relationship and external forces of wheel-rail in the SIMPACK software. Then, the normal force of wheel-rail is solved based on Hertz theory, and the tangential force of wheel-rail is calculated based on the FASTSIM algorithm through the MATLAB software. Next, in the MATLAB software, the wheel wear is calculated based on the Archard model, and a new wheel profile is obtained. Finally, the new wheel profile is re-input into the vehicle system dynamics model in the SIMPACK software to carry out cyclic calculation of wear.

The results show that the setting order of different curves has an obvious influence on wear when the proportion of the straight track and the curve is fixed. With the increase in running mileage, the severe wear zone is shifted from tread to flange root under the condition of the sequence-type track, but the wheel wear distribution is basically stable for the unit-type track, and their wear growth rates become closer. In the tracks with different straight-curved ratio, the more proportion the curved tracks occupy, the closer the severe wear zone is shifted to flange root. At the same time, an increase in weight of the vehicle load will aggravate the wheel wear, but it will not change the distribution of wheel wear. Compared with the measured data of one city B type metro in China, the numerical simulation results of wheel wear are nearly the same with the measured data.

These results will be helpful for metro tracks planning and can predict the trend of wheel wear, which has significant importance for the vehicle to do the repair operation. At the same time, the security risks of the vehicle are decreased economically and effectively.

At present, many scholars have studied the influence of metro tracks on wheel wear, but mainly focused on a straight line or a certain radius curve and neglected the influence of track sequence and track composition. This study is the first to examine the influence of track sequence on metro wheel wear by comparing the sequence-type track and unit-type track. The results show that the track sequence has a great influence on the wear distribution. At the same time, the influence of track composition on wheel wear is studied by comparing different straight-curve ratio tracks; therefore, wheel wear can be predicted integrally under different track conditions.

This study aims to investigate the effect of time-varying passenger flow on the wheel wear of metro vehicles to provide a more accurate model for predicting wheel wear and a new idea for reducing wheel wear.

Sectional passage flow data were collected from an operational metro line. A wheel wear simulation based on time-varying passenger flow was performed via the SIMPACK software to obtain the worn wheel profile and wear distribution. The simulation involves the following models: vehicle system dynamics model, wheel-track rolling contact model, wheel wear model and variable load application model. Later, the simulation results were compared with those obtained under the traditional constant load condition and the measured wear data.

For different distances traveled by the metro vehicle, the simulated wheel profile and wear distribution under the variable load remained closer to the measurements than those obtained under the constant load. As the distance traveled increased, the depth and position of maximum wear and wear growth rate under the variable load tended to approach the corresponding measured values. In contrast, the simulation results under the constant load differed greatly from the measured values. This suggests that the model accuracy under the variable load was significantly improved and the simulation results can offer a more accurate basis for wear prediction.

These results will help to predict wheel wear more accurately and provide a new idea for simulating wheel wear of metro vehicles. At the same time, measures for reducing wheel wear were discussed from the perspective of passenger flow changes.

Existing research on the wheel wear of metro vehicles is mainly based on the constant load condition, which is quite different from the variable load condition where the passenger flow in real vehicles varies over time. A method of simulating wheel wear based on time-varying load is proposed in this paper. The proposed method shows a great improvement in simulation accuracy compared to traditional methods and can provide a more accurate basis for wear prediction and wheel repair.