Search results

The emulation of synapses is essential to neuromorphic computing systems. Despite remarkable progress has been made in the two-terminal device (memristor), three-terminal transistors evoke greater attention because of the controlled conductance between the source and drain. The purpose of this paper is to investigate the synaptic plasticity of the TiO₂ nanowire transistor.

TiO₂ nanowire transistor was assembled by dielectrophoresis, and the synaptic plasticity such as paired-pulse facilitation, learning behaviors and high-pass filter were studied.

Facilitation index decreases with the increasing pulse interval. A bigger response current is obtained at the pulses with higher amplitude and smaller intervals, which is similar to the consolidated memory at the deeply and frequently learning. The increased current at the higher stimulus frequency demonstrates a promising application in the high-pass filter.

TiO₂ nanowire transistors possess broad application prospects in the future neural network.

The aim of this paper is to synthesize graphene-modified titanium dioxide (GR-TiO₂) nanorod arrays nanocomposite films, so that these can enhance the photocatalytic properties of titanium dioxide and overcome the problem of difficult separation and recovery of photocatalysts.

The GR-TiO₂ nanocomposite films were synthesized via hydrothermal method and spin-coating. The obtained samples were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), ultraviolet–visible (UV-Vis) diffuse reflectance spectrum and Raman spectrum. The photocatalytic performance of the GR-TiO₂ nanocomposite films for degrading Rhodamin B under ultraviolet (UV) was studied by a UV-Vis spectrophotometer. The photocatalytic enhancement mechanism of graphene was studied by photoelectrochemical analysis.

The introduction of graphene expanded the range of the optical response of TiO₂ nanorod arrays, improving the separation efficiency of the photogenerated electron-hole pairs, and thus dramatically increasing its photocatalytic performance.

A simple and novel way for synthesizing GR-TiO₂ nanocomposite films has enhanced the photocatalytic performance of TiO₂.

The photocatalyst synthesized is easy to separate and recycle in the process of photocatalytic reaction, so it is possible to achieve industrialization.

This paper aims to investigate the reusability of metal/metal oxide-coupled ZnO nanorods (ZnO NRs) to degrade rhodamine B (RhB).

ZnO NRs particles were synthesized by precipitation method and used to remove various types of metal ions such as Cu²⁺, Ag⁺, Mn²⁺, Ni²⁺, Pb²⁺, Cd²⁺ and Cr²⁺ ions under UV illumination. The metal/metal oxide-coupled ZnO NRs were characterized by scanning electron microscope, X-ray diffraction and UV-Vis diffuse reflectance. The photodegradation of RhB dye by these metal/metal oxide-coupled ZnO NRs under UV exposure was assessed.

The metal/metal oxide-coupled ZnO NRs were successfully reused to remove RhB dye in which more than >90% of RhB dye was degraded under UV exposure. Furthermore, the coupling of Ag, CuO, MnO₂, Cd and Ni particles onto the surface of ZnO NRs even enhanced the degradation of dye. The dominant reactive species involved in the degradation of RhB dye were ^•OH- and ^•O₂⁻-free radicals.

The coupling of metal/metal oxide onto the surface of ZnO NRs after metal ions removal could affect the photocatalytic performance of ZnO NRs in the degradation of organic pollutants in subsequent stage.

A good reusability performance of metal/metal oxide-coupled ZnO NRs make ZnO NRs become a desirable photocatalyst material for the treatment of wastewater, which consists of both heavy metal ions and organic dyes.

Metal/metal oxide coupling onto the surface of ZnO NRs particles improved subsequent UV-assisted photocatalytic degradation of RhB dye.

Personal thermal management in functional textiles is in increasing demand for health care, outdoor activity and energy saving. Thus, developing new strategies is highly desired for radiative cooling and/or heating by manipulation of the transmissivity, reflectivity and absorptivity of the textiles within solar energy and human body heat radiation ranges.

Inorganic additives including TiO2, Fe2O3, carbon black (CB), graphene and mica were incorporated into polymer films. The inorganic additives' full spectrum properties and thermal responses were comprehensively investigated.

The CB composite film showed the highest absorptivity over the full solar to human body radiation spectrum. The mica-white (mica-w) (mica coated with TiO2) and mica-red (mica-r) (mica coated with Fe2O3) composites showed the lowest solar energy absorptivity and a strong body heat radiation reflectivity. Furthermore, according to composites' thermal responses to the simulated solar and human body radiations, CB and mica are promising for both cooling and heating when applied in dual-functional thermal management textiles.

Research has limitation related the amount of additives which can be added to textile. When powder is added to polyester yarn, the amount is limited by 2–3%. When powder is added to the composite which is used for printing, the amount of powder is limited by 5%.

A lot of apparel, especially sport apparel, contains prints. Decoration is one part of print application. Now, a lot of companies work under development of different additives, which provide additional properties to apparel. The closest targets for powder added to prints are cooling and heat retention. Quite often, inorganic additives possess dual properties: the inorganic additives may be heat reflective which his needed for heat retention, but may have high-thermal conductivity, which works well for cooling. Human body has complicated mechanism of heat exchange: convection, radiation and moisture evaporations play main role. The same additive may be cooling if there is a contact with skin but may be heating (IR reflective) if placed in the second or third layer. Thus, effect is needed to be studied first before real application.

This work could provide a comprehensive guideline for the rational design and application of thermal management composite textile materials by revealing the full solar to human body radiation performance of a series of inorganic materials.

This paper aims to introduce constructed CeO2/TiO2 core/shell nanoparticle as sensitive substance organic compounds.

The CeO₂ nanoparticles were synthesized by hydrothermal treatment. Then CeO₂/TiO₂ core/shell was fabricated by sol–gel method preparation of TiO₂ in the presence of ceria nanoparticles and applied as the sensitive material to make a sensor.

Formation of the nanoparticles was confirmed by X-ray diffraction (XRD), energy dispersive spectroscopy (EDS), field emission scanning electron microscopy (FESEM) and high resolution transmission electron microscopy (HRTEM). The synthesized sensor exhibited not only good sensitivity to volatile organic compounds at room temperature but also logarithm of sensitivity versus concentrations was linear.

The sensor shows acceptable sensitivity to volatile organic compound at room temperature.

Experimental data revealed satisfactory reproducibility and short response and recovery times.

A radical mechanism for gas sensor reaction in two pathways was considered and activation energies were calculated by density functional theory (DFT) method to describe different sensitivities of tested volatile gases. The experimental results were consistent with the calculations.

In this study, an attempt has been made to collect the research that has been done on the construction and design of the H₂O₂ sensor. So far, many efforts have been made to quickly and sensitively determine H₂O₂ concentration based on different analytical principles. In this study, the importance of H₂O₂, its applications in various industries, especially the food industry, and the importance of measuring it with different techniques, especially portable sensors and on-site analysis, have been investigated and studied.

Hydrogen peroxide (H₂O₂) is a very simple molecule in nature, but due to its strong oxidizing and reducing properties, it has been widely used in the pharmaceutical, medical, environmental, mining, textile, paper, food production and chemical industries. Sensitive, rapid and continuous detection of H₂O₂ is of great importance in many systems for product quality control, health care, medical diagnostics, food safety and environmental protection.

Various methods have been developed and applied for the analysis of H₂O₂, such as fluorescence, colorimetry and electrochemistry, among them, the electrochemical technique due to its advantages in simple instrumentation, easy miniaturization, sensitivity and selectivity.

Monitoring the H₂O₂ concentration level is of practical importance for academic and industrial purposes. Edible oils are prone to oxidation during processing and storage, which may adversely affect oil quality and human health. Determination of peroxide value (PV) of edible oils is essential because PV is one of the most common quality parameters for monitoring lipid oxidation and oil quality control. The development of cheap, simple, fast, sensitive and selective H₂O₂ sensors is essential.

The purpose of this paper is to study the effect of synthesis conditions on properties of TiO₂ nanoparticles to be used for photocatalysis and also producing TiO₂ using a low temperature method.

TiO₂ nanoparticles were synthesised via a sol‐gel method at low temperature and the effect of parameters such as: synthesis temperature, HNO₃ concentration, calcination temperature and synthesis time on properties of TiO₂ were studied. The effects of the physico‐chemical properties of TiO₂, its concentration and light intensity on photocatalytic properties of TiO₂ nanoparticles were investigated also.

The results showed that TiO₂ with Anatase phase were formed at 80‐100°C by using proper HNO₃ concentration, synthesis time and calcinations temperature. Calcinations programme and temperature and also the synthesis time affect the formation of TiO₂ crystalline phase (i.e. Rutile and Brookite), their surface area and crystallite size. To evaluate the photocatalytic properties of TiO₂ nanoparticles, fluorescein was used as a model molecule. Results showed that degradation of fluorescein could be described by pseudo‐first order kinetics. The effect of TiO₂ concentration and light intensity on photocatalytic activity showed that increasing concentration of TiO₂ and the light intensity would increase the degradation of fluorescein.

The method used in this work to prepare TiO₂ nanoparticles is an economic method for low temperature synthesis of TiO₂ nanoparticles with high photocatalytic activity, which could find numerous applications in coating technology.

The purpose of this paper is to introduce flexible dye-sensitized solar cells (FDSSCs).

In the third generation solar cells, glass was used as a substrate, which due to its high weight and fragility, was not possible to produce continuously. However, in flexible solar cells, flexible substrates are used as new technology. The most important thing may choose a suitable substrate to produce a photovoltaic (PV) device with optimal efficiency.

Conductive plastics or metallic foils are the two main candidates for glass replacement, each with its advantages and disadvantages. As some high-temperature methods are used to prepare solar cells, metal substrates can be used to prepare PV devices without any problems. In contrast to the advantage of high thermal resistance in metals, metal substrates are dark and do not transmit enough light. In other words, metal substrates have a high loss of photon energy. Like all technologies, PV devices with polymer substrates have technical disadvantages.

In this study, the development of FDSSCs offers improved photovoltaic properties.

The most important challenge is the poor thermal stability of polymers compared to glass and metal, which requires special methods to prepare polymer solar cells. The second important point is choosing the suitable components and materials for this purpose.

Dependence of efficiency and performance of the device on the angle of sunlight, high-cost preparation devices components, limitations of functional materials such as organic-mineral sensitizers, lack of close connection between practical achievements and theoretical results and complicated fabrication process and high weight.