Search results

The purpose of this study is to model the dependences of the output voltage, temperature, current and electrical power dissipation of a voltage limiter based on a two-layer varistor–posistor structure on time and analysis the influence of operating modes and design parameters of such a limiter on these characteristics.

The behavior of the limiting voltage, temperature and other parameters of the voltage limiter when an input constant overvoltage is applied is studied by the simulation method. The voltage limiter was a two-layer construction. One layer was a zinc oxide ceramic varistor. The second layer was a posistor polymer composite with a nanocarbon filler of PolySwitch technology.

The output voltage across the varistor layer decreases and reaches some fixed value related to its breakdown voltage after applying a constant overvoltage to the structure over time. The temperature of the structure increases to some steady state value, while the current decreases significantly. The amplitude of the transient current pulse increases, its duration and energy of the transient process decrease with increasing overvoltage. An increase in the internal resistance of the overvoltage source can cause a decrease in the amplitude and an increase in the duration of transient currents.

The ranges of values for the activation energy of conduction of the varistor layer in weak electric fields, the intensity of heat exchange between the structure under study and the environment are determined to ensure the stable operation of this structure as a voltage limiter. The results obtained make it possible to select the necessary parameters of the indicated structures to ensure the required operating modes of the voltage limiter for various applications.

Resin-based friction materials are the most widely used key materials in industry for braking and transmission. However, the friction coefficient of resin-based friction materials significantly decreases at temperatures above 300°C, which reduces their friction performance.

This study combines elevated-temperature mechanical experiments with friction and wear experiments to explain the thermal degradation resistance performance and temperature recovery performance of resin-based friction materials. It also investigates the influence of friction material strength and worn morphology on the friction coefficient of materials at elevated temperature.

The experimental results show that the increase in friction coefficient of friction materials below 300°C is mainly due to the increase in worn morphology characterization parameters, and the thermal degradation phenomenon above 300°C is mainly due to the decrease of shear strength of friction film. Basalt fiber can significantly improve the thermal degradation resistance of friction materials. The friction coefficient of basalt fiber-reinforced specimens after thermal degradation reaches 0.421–0.443, which is 19–25% higher than the original. The thermal decay rate is 9.03–11.0%, which is 7.9–9.87% lower than the original. Moreover, the friction coefficient has good cooling recovery performance.

Revealed the thermal degradation mechanism of resin-based friction materials, verified that basalt fibers can improve the thermal degradation resistance of friction materials and provided reference for the development of new friction materials.

This paper aims to improve the wear resistance of titanium alloy using a high-hardness boride layer, which was fabricated on Ti6Al4V by a high-temperature boronizing process.

The boride layers on Ti6Al4V were obtained at 1000°C for 5–15 h. Scanning electron microscopy, energy dispersive analysis and X-ray diffractometer were used to characterize the properties of the boride layer. The tribological performance of the boride layer at room and elevated temperatures was investigated.

The X-ray diffraction analysis showed that the boride layers were a dual-phase structure of TiB and TiB₂. When the boronizing time increased from 5 h to 15 h, the microhardness increased from 1192 HV_0.5 to 1619.8 HV_0.5. At 25°C and elevated temperatures, the friction coefficients of the boride layers were higher than that of Ti6Al4V. The wear track areas of T-5 at 200°C and 400°C were 2.5 × 10^–3 and 1.1 × 10^–3 mm², respectively, which were 6.1% and 2.6% of that of Ti6Al4V, indicating boride layer exhibited a significant wear resistance. The wear mechanisms of the boride layer transformed from slight peeling to oxidative wear and abrasive wear as the temperature was raised.

The findings provide an effective strategy for improving the wear resistance of Ti6Al4V and have important implications for the application of titanium alloy in a high-temperature field.

In the analysis of structures in a fire situation by simplified and analytical methods, one assumption is that the fire resistance time is greater than or equal to the required fire resistance time. Among the methodologies involving the fire resistance time, the most used is the tabular method, which associates fire resistance time values to structural elements based on minimum dimensions of the cross section. The tabular method is widely accepted by the technical-scientific community due to the fact that it is safe and practical. However, its main criticism is that it results in lower fire resistance times than advanced thermal and thermostructural analysis methods. The objective of this study was to evaluate the fire resistance time of reinforced concrete beams and compare it with the required fire resistance time recommended by the tabular method of NBR 15200 (ABNT, 2012).

The fire resistance time and required fire resistance time of reinforced concrete beams were evaluated using, respectively, numerical models developed based on the finite element method and the tabular method of NBR 15200 (ABNT, 2012). The influence of the following parameters was investigated: longitudinal reinforcement cover, characteristic compressive strength of concrete, beam height, longitudinal reinforcement area and arrangement of steel bars.

Among the evaluated parameters, the covering of the longitudinal reinforcement proved to be more relevant for the fire resistance time, justifying that the tabular method of NBR 15200 (ABNT, 2012) being strongly and directly influenced by this parameter. In turn, more resistant concretes, higher beams and higher steel grades have lower fire resistance time values. This is because beams in these conditions have greater resistance capacity at room temperature and, consequently, are subject to external stresses of greater magnitude. In some cases, the fire resistance time was even lower than the required fire resistance time prescribed by NBR 15200 (ABNT, 2012). Both the fire resistance time and the required fire resistance time were not influenced by the arrangement of the longitudinal reinforcements.

The present paper innovates by demonstrating the influence of other important design variables on the required fire resistance time of the NBR 15200 (ABNT, 2012). Among several conclusions, it was found that the load level to which the structural elements are subjected considerably affects their fire resistance time. For this reason, it was recommended that the methods for calculating the required fire resistance time consider the load level. In addition, the article quantifies the security degree of the tabular method and exposes some situations for which the tabular method proved to be unsafe. Moreover, in all the models analyzed, the relationship between the span and the vertical deflection associated with the failure of the beams in a fire situation was determined. With this, a span over average deflection relationship was presented in which beams in fire situations fail.

Preparing CrAlN coatings on the surface of silicon nitride bearings can improve their service life in oil-free lubrication. This paper aims to match the optimal process parameters for preparing CrAlN coatings on silicon nitride surfaces, and reveal the microscopic mechanism of process parameter influence on coating wear resistance.

This study used molecular dynamics to analyze how process parameters affected the nucleation density, micromorphology, densification and internal stress of CrAlN coatings. An orthogonal test method was used to examine how deposition time, substrate temperature, nitrogen-argon flow rate and sputtering power impacted the wear resistance of CrAlN coatings under dry friction conditions.

Nucleation density, micromorphology, densification and internal stress have a significant influence on the surface morphology and wear resistance of CrAlN coatings. The process parameters for better wear resistance of the CrAlN coatings were at a deposition time of 120 min, a substrate temperature of 573 K, a nitrogen-argon flow rate of 1:1 and a sputtering power of 160 W.

Simulation analysis and experimental results of this paper can provide data to assist in setting process parameters for applying CrAlN coatings to silicon nitride bearings.

The type 120 emergency valve is an essential braking component of railway freight trains, but corresponding diaphragms consisting of natural rubber (NR) and chloroprene rubber (CR) exhibit insufficient aging resistance and low-temperature resistance, respectively. In order to develop type 120 emergency valve rubber diaphragms with long-life and high-performance, low-temperatureresistant CR and NR were processed.

The physical properties of the low-temperature-resistant CR and NR were tested by low-temperature stretching, dynamic mechanical analysis, differential scanning calorimetry and thermogravimetric analysis. Single-valve and single-vehicle tests of type 120 emergency valves were carried out for emergency diaphragms consisting of NR and CR.

The low-temperature-resistant CR and NR exhibited excellent physical properties. The elasticity and low-temperature resistance of NR were superior to those of CR, whereas the mechanical properties of the two rubbers were similar in the temperature range of 0 °C–150 °C. The NR and CR emergency diaphragms met the requirements of the single-valve test. In the low-temperature single-vehicle test, only the low-temperature sensitivity test of the NR emergency diaphragm met the requirements.

The innovation of this study is that it provides valuable data and experience for future development of type 120 valve rubber diaphragms.

This paper aims to present a novel approach for computing particle temperatures in simulations coupling computational fluid dynamics (CFD) and discrete element method (DEM) to predict flow and heat transfer in fluidized beds of thermally thick spherical particles.

An improved lumped formulation based on Hermite-type approximations for integrals to relate surface temperature to average temperature and surface heat flux is used to overcome the limitations of classical lumped models. The model is validated through comparisons with analytical solutions for a convectively cooled sphere and experimental data for a fixed particle bed. The coupled CFD-DEM model is then applied to simulate a Geldart D bubbling fluidized bed, comparing the results to those obtained using the classical lumped model.

The validation cases demonstrate that ignoring internal thermal resistance can significantly impact the temperature in cases where the Biot number is greater than 0.1. The results for the fixed bed case clearly demonstrate that the proposed method yields significantly improved outcomes compared to the classical model. The fluidized bed results show that surface temperature can deviate considerably from the average temperature, underscoring the importance of accurately accounting for surface temperature in convective heat transfer predictions and surface processes.

The proposed approach offers a physically more consistent simulation without imposing a significant increase in computational cost. The improved lumped formulation can be easily and inexpensively integrated into a typical DEM solver workflow to predict heat transfer for spherical particles, with important implications for various industrial applications.

The purpose of this work is to design the wire beam electrode (WBE) of P110 steel and study its corrosion behavior and mechanism under high temperature and pressure.

Packaging materials of the new type P110 steel WBE and high pressure stable WBE structure were designed. A metallurgical microscope (XJP-3C) and scanning electron microscopy (EV0 MA15 Zeiss) with an energy dispersive spectrometer were used to analyze the microstructure and composition of the P110 steel. The electrochemical workstation (CS310, CorrTest Instrument Co., Ltd) with a WBE potential and current scanner was used to analyze the corrosion mechanism of P110 steel.

According to the analysis of Nyquist plots at different temperatures, the corrosion resistance of P110 steel decreases with the increase of temperature under atmospheric pressure. In addition, R_p of P110 steel under high pressure is maintained in the range of 200 ∼ 375 Ωcm², while that under atmospheric pressure is maintained in the range of 20 ∼ 160 Ωcm², indicating that the corrosion products on P110 steel under high pressure is denser, which improves the corrosion resistance of P110 steel to a certain extent.

The WBE applied in high temperature and pressure environment is in blank. This work designed and prepared a WBE of P110 steel for high temperature and pressure environment, and the corrosion mechanism of P110 steel was revealed by using the designed WBE.

Tantalum is a kind of metal material with moderate hardness, high ductility, small thermal expansion coefficient, excellent corrosion resistance and outstanding biocompatibility. The purpose of this study is that its tribological performance could be tested and analyzed so as to use it in different fields.

The friction resistance of a-Ta under dry friction conditions was tested at different roads. The relationships between load and friction coefficient, wear rate and two-dimensional shape of wear scars were studied.

The stable Ta₂O₅ film with lubrication effect was generated in the process of friction. And, the larger the test load, the more Ta₂O₅ would be generated.

This work lays a theoretical foundation for tantalum as an excellent wear-resistant material.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-02-2023-0047/

The purpose of this paper is to reveal the dynamic contact characteristics of the slip ring. Dynamic contact resistance models considering wear and self-excited were established based on fractal theory.

The effects of tangential velocity, stiffness and damping coefficient on dynamic contact resistance are studied. The relationships between fractal parameters, wear time and contact parameters are revealed.

The results show that the total contact area decreases with the friction coefficient and fractal roughness under the same load. Self-excited vibration occurs at a low speed (less than 0.6 m/s). It transforms from stick-slip motion at 0.4 m/s to pure sliding at 0.5 m/s. A high stiffness makes contact resistance fluctuate violently, while increasing the damping coefficient can suppress the self-excited vibration and reduce the dynamic contact resistance. The fractal contact resistance model considering wear is established based on the fractal parameters models. The validity of the model is verified by the wear tests.

The results have a great significance to study the electrical contact behavior of conductive slip ring.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-09-2023-0300/