Search results

To contribute to the identification of the parameters influencing the behavior of textile-reinforced concrete (TRC), the purpose of this paper is to investigate the flexural behavior of TRC-based plates under four-point bending notably designed in the context of sustainable development and the substitution of mortar components with natural and abundant materials.

An extensive experimental campaign was focused about two main parameters. The first one emphases the textile reinforcements, such as the number of layers, the nature and the textile mesh size. In the second step, the composition of the mortar matrix was explored through the use of dune sand as a substitute of the river one.

Test results in terms of load-displacement response and failure patterns were highlighted, discussed and confronted to literature ones. As key findings, an increase of the load-bearing capacity and ductility, comparable to the use of an industrially produced second textile layer was recorded with the use of dune sand in the mortar mix design. The designed ecofriendly samples with economic concerns denote the significance of obtained outcomes in this research study.

The novelty of the present work was to valorize the use of natural dune sand to design new TRC samples to respond to the environmental and economical requirements. The obtained values provide an improved textiles–matrix interface performance compared to classical TRC samples issued from the literature.

This study aims to realize the multipurpose use of inorganic materials in adsorption treatment of pigment wastewater and preparation of core-modified Color Index Pigment Red 57:1 (C.I. Pigment Red 57:1, PR 57:1).

In this paper, the inorganic materials (sepiolite and SiO₂·nH₂O) were used in both PR 57:1 production wastewater treatment and its core-modification. The inorganic material firstly adsorbed 3-hydroxy-2-naphthoic acid (bon acid) in the pigment wastewater to reduce chemical oxygen demand. Then, the inorganic material adsorbed with bon acid was reused to prepare core-modified PR 57:1.

In the pigment wastewater adsorption experiment, it was found that under pH = 3, the adsorption percentage of bon acid by inorganic material can reached up to 46.00%. The pigment characterization results showed that the core-modified PR 57:1 had a core-shell structure. Under UV light irradiation for 1 h, the core-modified PR 57:1 prepared with sepiolite and SiO₂·nH₂O showed total color difference ΔE value of 1.43 and 2.05, respectively, which was lower than that of unmodified PR 57:1 (ΔE = 2.89). In addition, the transmittance of pigment water suspension test results showed that the core-modified PR 57:1 showed better water dispersibility.

This paper attempts to develop a synergistic strategy based on the multipurpose use of inorganic materials in adsorption treatment of pigment wastewater and preparation of core-modified PR 57:1.

This study aims to determine the effect of replacing a portion of the cement in the concrete mixture with silica fume (SF) on the corrosion resistance of reinforcing bars, the compressive strength of concrete and the tensile strength of hook bars in both corroded and non-corroded external joints of structures. The external beam-column connection was studied because of its critical role in maintaining structural continuity in all three directions and providing resistance to rotation.

In external concrete joints, the bars at the end of the beams are often bent at 90° to form hooks that embed in columns. Owing to the importance of embedding distance and the need to understand its susceptibility to corrosion damage from chloride attack, a series of experiments were conducted on 12 specimens that accurately simulate real-site conditions in terms of dimensions, reinforcement and hook bars. SF was replaced with 10% and 15% of the weight of cement in the concrete mixture. To simulate corrosion, the specimens were subjected to accelerated corrosion in the laboratory by applying a low continuous current of 0.35 mA for 58 days.

The results revealed the effect of SF in improving the compressive strength of concrete, the pullout resistance of the hook bars and the corrosion resistance. In addition, it showed an apparent effect of the corrosion of reinforcing bars in reducing the bonding strength of hook bars with concrete and the effect of SF in improving this strength.

It was noted that the improvement of the results, achieved by replacing 10% of the weight of cement with SF, was significantly close to the results obtained by replacing 15% of the SF. It is recommended that an SF ratio of 10% be adopted to achieve the greatest economic savings.

This paper aims to produce lightweight concrete by combining aerated concrete with expanded polystyrene beads concrete to create structural aerated-polystyrene lightweight concrete that satisfies the criteria of sustainability for thermal and sound insulation properties and the structural criteria of having satisfactory compressive strength for structural elements.

The experimental study was carried out to reach the largest compressive strength while maintaining the lowest possible density by preparing nine mixes of concrete, involving different ratios of aluminum waste powder and polystyrene beads as 0%, 0.2% and 0.3% and 0%, 0.1% and 0.2%, respectively, by weight of cement to produce the lightweight concrete with different densities. The performance of mechanical properties, thermal conductivity, ultrasonic pulse velocity, density, modulus of elasticity, acoustic impedance and scanning electron microscopy were studied and discussed.

Results showed that aerated-expended polystyrene beads concrete had the most suitable properties when the proportions of aluminum waste powder and expanded polystyrene beads were 0.2% and 0.1%, respectively. The compressive strength, density, thermal conductivity and acoustic impedance were 38.5 MPa, 1,768 Kg/m³, 0.358 W/(m.k) and 4.91 Kg/m² s, respectively.

The experimental work was done using aluminum scrap waste powder as an expanding agent to produce aerated concrete and combining it with expanded polystyrene bead concrete to produce structural aerated-polystyrene concrete, which contains fine materials (silica fume and local natural raw limestone) and superplasticizers.

Present work deals with the partial substitution of cement by waste demolished concrete powder (WDP) for reducing the carbon footprints of concrete.

Control specimens and the specimens with 20% WDP as fractional substitute of cement were prepared. The waste powder was thermally activated at 825 °C prior to its use in the mix. The prepared specimens were evaluated in terms of density, workability, mechanical strength, Ultrasonic pulse velocity (UPV) and rebound hammer (RH).

The results showed that with the substitution, the workability of the mix increased, while the density decreased. A decrement within a 20% limit was found in compressive strength. The UPV and RH results were closely linked to the other results as mentioned above.

The study deals with only M15 concrete and the substitution level of only 20% as a baseline.

The concrete containing 20% WDP is lightweight and more workable. Moreover, its strength at 28 days is 14 MPa, only 1 MPa lesser than the characteristic strength.

The WDP can be recycled and the dumping in landfills can be reduced. This is an important effort towards the decarbonation of concrete.

Previous literature indicates that the WDP has been frequently used as a partial replacement of aggregates. However, some traces of secondary hydration were also reported. This work considers the effect of partial substitution of cement by the WDP.

The purpose of this paper is to study and analyze the effects of fly ash (FA) as a mineral admixture on compressive strength (CS), carbonation resistance and corrosion resistance of reinforced concrete (RC). In addition, the utilization of inexpensive and abundantly available FA as a cement replacement in concrete has several benefits including reduced OPC usage and elimination of the FA disposal problem.

Reinforcement corrosion and carbonation significantly affect the strength and durability of the RC structures. Also, the utilization of FA as green corrosion inhibitors, which are nontoxic and environmentally friendly alternatives. This review discusses the effects of FA on the mechanical characteristics of concrete. Also, this review analyzes the impact of FA as a partial replacement of cement in concrete and its effect on the depth of carbonation in concrete elements and the corrosion rate of embedded steel as well as the chemical composition and microstructure (X-ray diffraction analysis and scanning electron microscopy) of FA concrete were also reviewed.

This review provides a clear analysis of the available study, providing a thorough overview of the current state of knowledge on this topic. Regarding concrete CS, the findings indicate that the incorporation of FA often leads to a loss in early-age strength. However, as the curing period increased, the strength of fly ash concrete (FAC) increased with or even surpassed that of conventional concrete. Analysis of the accelerated carbonation test revealed that incorporating FA into the concrete mix led to a shallower carbonation depth and slower diffusion of carbon dioxide (CO₂) into the concrete. Furthermore, the half-cell potential test shows that the inclusion of FA increases the durability of RC by slowing the rate of steel-reinforcement corrosion.

This systematic review analyzes a wide range of existing studies on the topic, providing a comprehensive overview of the research conducted so far. This review intends to critically assess the enhancements in mechanical and durability attributes (such as CS, carbonation and corrosion resistance) of FAC and FA-RC. This systematic review has practical implications for the construction and engineering industries. This can support engineers and designers in making informed decisions regarding the use of FA in concrete mixtures, considering both its benefits and potential drawbacks.

This study aims to address sustainability challenges in construction by exploring the structural performance and environmental benefits of incorporating pozzolanic waste glass (WG) into ultra-high-performance reinforced concrete (UHPRC) beams.

A comprehensive evaluation of UHPRC beams was conducted, incorporating varying ratios (10%, 20% and 30%) of WG powder alongside a consistent 0.75% inclusion of basalt fiber. The investigation encompassed the entire UHPRC production process, including curing, casting and molding, while evaluating workability and physical properties. Furthermore, the environmental impact, particularly CO₂ emissions associated with UHPRC mixture components, was also assessed. Type K thermocouples were employed to analyze temperature dynamics during fabrication, providing valuable insights.

The findings demonstrate positive implications for using pozzolanic WG as a cement substitute in UHPRC beams.

This research stands out for its unique focus on the combined effects of incorporating recycled pozzolanic glass waste on the structural performance and environmental footprint of UHPRC beams.

The purpose of this paper is to examine the use of phragmites australis ash (PAA) in cementitious systems to achieve sustainable construction.

In this paper, the properties of mortar containing PAA as partial cement replacement are determined. The PAA is produced through slow burning in a closed system to minimize the CO₂ emission. A total of four mortar mixes are prepared with PAA replacement levels ranging from 0% to 30% by weight. The water to binder and the proportions of binder to sand are 0.55 and 1:3 by weight, respectively. The properties tested are density, compressive strength, flexural strength, ultrasonic pulse velocity, water absorption by total immersion and capillary rise. Testing is conducted at 1, 7, 28 and 90 days.

While there is a decrease in strength as the amount of PAA increases, there is strong indication of pozzolanic reaction in the presence of PAA. This is in agreement with the results reported by Salvo et al. (2015), where they found noticeable pozzolanic activities in the presence of straw ash, which is rich in SiO₂ and relatively high K₂O content. At 90 days of curing, there is a decrease of 5% in compressive strength at 10% PAA replacement. However, at 20% and 30% replacement, the reduction in compressive strength is 23% and 32%, respectively. The trend in flexural strength and ultrasonic pulse velocity is similar to that in compressive strength. The water absorption by total immersion and capillary rise tends to increase with increasing amounts of PAA in the mix. There seems to be a linear relationship between water absorption and compressive strength at each curing age.

The Phragmites australis plant used in this investigation is obtained from one location and this present a limitation as the type of soil may change the properties. Also one method of slow burning is used. Different burning methods may alter the composition of the PAA.

This outcome of this research will contribute towards sustainable development as it will make use of the waste generated, reduce the amount of energy-intensive cement used in construction and help generate local employment in the area where the Phragmites australis plant grows.

To the best knowledge of the authors, the ash from the Phragmites australis plant has not been used in cementitious system and this research can be considered original as it examines the properties of mortar containing PAA. Also, the process of burning in a closed system using this material.

Low-carbon concrete represents a new direction in mitigating the global warming effects caused by clinker manufacturing. Utilizing Saudi agro-industrial by-products as an alternative to cement is a key support in reducing clinker production and promoting innovation in infrastructure and circular economy concepts, toward decarbonization in the construction industry. The use of fly ash (FA) as a cement alternative has been researched and proven effective in enhancing the durability of FA-based concrete, especially at lower replacement levels. However, at higher replacement levels, a noticeable impediment in mechanical strength indicators limits the use of this material.

In this study, low-carbon concrete mixes were designed by replacing 50% of the cement with FA. Varying ratios of nano-sized glass powder (4 and 6% of cement weight) were used as nanomaterial additives to enhance the mechanical properties and durability of the designed concrete. In addition, a 10% of the mixing water was replaced with EMs dosage.

The results obtained showed a significant positive impact on resistance and durability properties when replacing 10% of the mixing water with effective microorganisms (EMs) broth and incorporating nanomaterial additives. The optimal mix ratios were those designed with 10% EMs and 4–6% nano-sized glass powder additives. However, it can be concluded that advancements in eco-friendly concrete additive technologies have made significant contributions to the development of sophisticated concrete varieties.

This study focused at developing nanomaterial additives from Saudi industrial wastes and at presenting a cost-effective and feasible solution for enhancing the properties of FA-based concrete. It has also been found that the inclusion of EMs contributes effectively to enhancing the concrete's resistance properties.

This study aims to investigate the behavior of the green biomass-derived copper (lignin/silica/fatty acids) complex, copper lignin/silica/fatty acids (Cu-LSF) complex, when incorporated into the nonpolar ethylene propylene diene (EPDFM) rubber matrix, focusing on its reinforcing and antioxidant effect on the resulting EPDM composites.

The structure of the prepared EPDM composites was confirmed by Fourier-transform infrared spectroscopy, and the dispersion of the additive fillers and antioxidants in the EPDM matrix was investigated using scanning electron microscopy. Also, the rheometric characteristics, mechanical properties, swelling behavior and thermal gravimetric analysis of all the prepared EPDM composites were explored as well.

Results revealed that the Cu-LSF complex dispersed well in the nonpolar EPDM rubber matrix, in thepresence of coupling system, with enhanced Cu-LSF-rubber interactions and increased cross-linking density, which reflected on the improved rheological and mechanical properties of the resulting EPDM composites. From the various investigations performed in the current study, the authors can suggest 7–11 phr is the optimal effective concentration of Cu-LSF complex loading. Interestingly, EPDM composites containing Cu-LSF complex showed better antiaging performance, thermal stability and fluid resistance, when compared with those containing the commercial antioxidants (2,2,4-trimethyl-1,2-dihydroquinoline and N-isopropyl-N’-phenyl-p-phenylenediamine). These findings are in good agreement with our previous study on polar nitrile butadiene rubber.

The current study suggests the green biomass-derived Cu-LSF complex to be a promising low-cost and environmentally safe alternative filler and antioxidant to the hazardous commercial ones.