Search results

Ciliated microelectromechanical system (MEMS) vector hydrophones pick up sound signals through Wheatstone bridge in cross beam-ciliated microstructures to achieve information transmission. This paper aims to overcome the complexity and variability of the marine environment and achieve accurate location of targets. In this paper, a new method for ocean noise denoising based on improved complete ensemble empirical mode decomposition with adaptive noise combined with wavelet threshold processing method (CEEMDAN-WT) is proposed.

Based on the CEEMDAN-WT method, the signal is decomposed into different intrinsic mode functions (IMFs), and relevant parameters are selected to obtain IMF denoised signals through WT method for the noisy mode components with low sample entropy. The final pure signal is obtained by reconstructing the unprocessed mode components and the denoising component, effectively separating the signal from the wave interference.

The three methods of empirical mode decomposition (EMD), ensemble empirical mode decomposition (EEMD) and CEEMDAN are compared and analyzed by simulation. The simulation results show that the CEEMDAN method has higher signal-to-noise ratio and smaller reconstruction error than EMD and EEMD. The feasibility and practicability of the combined denoising method are verified by indoor and outdoor experiments, and the underwater acoustic experiment data after processing are combined beams. The problem of blurry left and right sides is solved, and the high precision orientation of the target is realized.

This algorithm provides a theoretical basis for MEMS hydrophones to achieve accurate target positioning in the ocean, and can be applied to the hardware design of sonobuoys, which is widely used in various underwater acoustic work.

The call for supply chain transparency (SCT), especially the environmental, social and governance (ESG) aspect, is getting increasingly louder. Based on the signaling theory, our study investigates the operational benefit of supply chain transparency in terms of ESG (SCT-ESG). To further clarify the signaling process, the moderating roles of digitalization of the firm and signal strength are also examined.

Longitudinal secondary data from multiple databases are matched and analyzed using ordinary least squares (OLS) regressions to validate the proposed hypotheses.

Results suggest that with SCT-ESG, firms have a weakened disparity between production variance and demand variance, and the supply chain experiences a reduced bullwhip effect. Further, digitalization of the focal company and signal strength reinforce the negative effect of SCT-ESG on the bullwhip effect.

The study integrates the SCT and ESG literature through SCT-ESG, extending benefits of ESG disclosure to the supply chain context. It extends the application of the signaling theory in OSCM by including contextual factors of digitalization and signal strength.

This study aims to improve the mechanical properties of an object produced by fused deposition modelling with high-grade polymer.

The study uses an ensembled surrogate-assisted evolutionary algorithm (SAEA) to optimize the process parameters for example, layer height, print speed, print direction and nozzle temperature for enhancing the mechanical properties of temperature-sensitive high-grade polymer poly-ether-ether-ketone (PEEK) in fused deposition modelling (FDM) 3D printing while considering print time as one of the important parameter. These models are integrated with an evolutionary algorithm to efficiently explore parameter space. The optimized parameters from the SAEA approach are compared with those obtained using the Gray Relational Analysis (GRA) Taguchi method serving as a benchmark. Later, the study also highlights the significant role of print direction in optimizing the mechanical properties of FDM 3D printed PEEK.

With the use of ensemble learning-based SAEA, one can successfully maximize the ultimate stress and percentage elongation with minimum print time. SAEA-based solution has 28.86% higher ultimate stress, 66.95% lower percentage of elongation and 7.14% lower print time in comparison to the benchmark result (GRA Taguchi method). Also, the results from the experimental investigation indicate that the print direction has a greater role in deciding the optimum value of mechanical properties for FDM 3D printed high-grade thermoplastic PEEK polymer.

This study is valid for the parameter ranges, which are defined to conduct the experimentation.

This study has been conducted on the basis of taking only a few important process parameters as per the literatures and available scope of the study; however, there are many other parameters, e.g. wall thickness, road width, print orientation, fill pattern, roller speed, retraction, etc. which can be included to make a more comprehensive investigation and accuracy of the results for practical implementation.

This study deploys a novel meta-model-based optimization approach for enhancing the mechanical properties of high-grade thermoplastic polymers, which is rarely available in the published literature in the research domain.

Unlike many existing methods that are primarily focused on two-dimensional localization, this research paper extended the scope to three-dimensional localization. This enhancement is particularly significant for unmanned aerial vehicle (UAV) applications that demand precise altitude information, such as infrastructure inspection and aerial surveillance, thereby broadening the applicability of UAV-assisted wireless networks.

The paper introduced a novel method that employs recurrent neural networks (RNNs) for node localization in three-dimensional space within UAV-assisted wireless networks. It presented an optimization perspective to the node localization problem, aiming to balance localization accuracy with computational efficiency. By formulating the localization task as an optimization challenge, the study proposed strategies to minimize errors while ensuring manageable computational overhead, which are crucial for real-time deployment in dynamic UAV environments.

Simulation results demonstrated significant improvements, including a channel capacity of 99.95%, energy savings of 89.42%, reduced latency by 99.88% and notable data rates for UAV-based communication with an average localization error of 0.8462. Hence, the proposed model can be used to enhance the capacity of UAVs to work effectively in diverse environmental conditions, offering a reliable solution for maintaining connectivity during critical scenarios such as terrestrial environmental crises when traditional infrastructure is unavailable.

Conventional localization methods in wireless sensor networks (WSNs), such as received signal strength (RSS), often entail manual configuration and are beset by limitations in terms of capacity, scalability and efficiency. It is not considered for 3-D localization. In this paper, machine learning such as multi-layer perceptrons (MLP) and RNN are employed to facilitate the capture of intricate spatial relationships and patterns (3-D), resulting in enhanced localization precision and also improved in channel capacity, energy savings and reduced latency of UAVs for wireless communication.

The safe operation of the metro power transformer directly relates to the safety and efficiency of the entire metro system. Through voiceprint technology, the sounds emitted by the transformer can be monitored in real-time, thereby achieving real-time monitoring of the transformer’s operational status. However, the environment surrounding power transformers is filled with various interfering sounds that intertwine with both the normal operational voiceprints and faulty voiceprints of the transformer, severely impacting the accuracy and reliability of voiceprint identification. Therefore, effective preprocessing steps are required to identify and separate the sound signals of transformer operation, which is a prerequisite for subsequent analysis.

This paper proposes an Adaptive Threshold Repeating Pattern Extraction Technique (REPET) algorithm to separate and denoise the transformer operation sound signals. By analyzing the Short-Time Fourier Transform (STFT) amplitude spectrum, the algorithm identifies and utilizes the repeating periodic structures within the signal to automatically adjust the threshold, effectively distinguishing and extracting stable background signals from transient foreground events. The REPET algorithm first calculates the autocorrelation matrix of the signal to determine the repeating period, then constructs a repeating segment model. Through comparison with the amplitude spectrum of the original signal, repeating patterns are extracted and a soft time-frequency mask is generated.

After adaptive thresholding processing, the target signal is separated. Experiments conducted on mixed sounds to separate background sounds from foreground sounds using this algorithm and comparing the results with those obtained using the FastICA algorithm demonstrate that the Adaptive Threshold REPET method achieves good separation effects.

A REPET method with adaptive threshold is proposed, which adopts the dynamic threshold adjustment mechanism, adaptively calculates the threshold for blind source separation and improves the adaptability and robustness of the algorithm to the statistical characteristics of the signal. It also lays the foundation for transformer fault detection based on acoustic fingerprinting.

The study aims to determine the the optimal value of output parameters of a variable compression ratio (CR) diesel engine are investigated at different loads, CR and fuel modes of operation experimentally. The output parameters of a variable compression ratio (CR) diesel engine are investigated at different loads, CR and fuel modes of operation experimentally. The performance parameters like brake thermal efficiency (BTE) and brake specific energy consumption (BSEC), whereas CO emission, HC emission, CO₂ emission, NO_x emission, exhaust gas temperature (EGT) and opacity are the emission parameters measured during the test. Tests are conducted for 2, 6 and 10 kg of load, 16.5 and 17.5 of CR.

In this investigation, the first engine was fueled with 100% diesel and 100% Calophyllum inophyllum oil in single-fuel mode. Then Calophyllum inophyllum oil with producer gas was fed to the engine. Calophyllum inophyllum oil offers lower BTE, CO and HC emissions, opacity and higher EGT, BSEC, CO₂ emission and NO_x emissions compared to diesel fuel in both fuel modes of operation observed. The performance optimization using the Taguchi approach is carried out to determine the optimal input parameters for maximum performance and minimum emissions for the test engine. The optimized value of the input parameters is then fed into the prediction techniques, such as the artificial neural network (ANN).

From multiple response optimization, the minimum emissions of 0.58% of CO, 42% of HC, 191 ppm NO_x and maximum BTE of 21.56% for 16.5 CR, 10 kg load and dual fuel mode of operation are determined. Based on generated errors, the ANN is also ranked for precision. The proposed ANN model provides better prediction with minimum experimental data sets. The values of the R² correlation coefficient are 1, 0.95552, 0.94367 and 0.97789 for training, validation, testing and all, respectively. The said biodiesel may be used as a substitute for conventional diesel fuel.

The blend of Calophyllum inophyllum oil-producer gas is used to run the diesel engine. Performance and emission analysis has been carried out, compared, optimized and validated.

An emerging body of literature has pinpointed the role of supply chain structure in influencing the extent to which supply chain members disclose information about their internal practices and performance. Nevertheless, empirical research investigating the effects of firm-level relational embeddedness on network-level transparency still lags. Drawing on social network analysis, this research examines the effect of relational embeddedness on supply chain transparency and the contingent role of digitalization in the context of environmental, social and governance (ESG) information disclosure.

In their empirical analysis, the authors collected secondary data from the Bloomberg database about 2,229 firms and 14,007 ties organized in 107 extended supply chains. The authors employed supplier and customer concentration metrics to measure relational embeddedness and performed multiple econometric models to test the hypothesis.

The authors found a positive effect of supplier concentration on supply chain transparency, but the effect of customer concentration was not significant. Additionally, the digitalization of focal firms reinforced the impact of supplier concentration on supply chain transparency.

The study findings contribute by underscoring the critical effect of relational embeddedness on supply chain transparency, extending prior literature on social network analysis, providing compelling evidence for the intersection of digitalization and supply chain management, and drawing important implications for practices.

This paper aims to report the effect of titanium oxide (TiO₂) particles on the specific wear rate (SWR) of alkaline treated bamboo and flax fiber-reinforced composites (FRCs) under dry sliding condition by using a robust statistical method.

In this research, the epoxy/bamboo and epoxy/flax composites filled with 0–8 Wt.% TiO₂ particles have been fabricated using simple hand layup techniques, and wear testing of the composite was done in accordance with the ASTM G99-05 standard. The Taguchi design of experiments (DOE) was used to conduct a statistical analysis of experimental wear results. An analysis of variance (ANOVA) was conducted to identify significant control factors affecting SWR under dry sliding conditions. Taguchi prediction model is also developed to verify the correlation between the test parameters and performance output.

The research study reveals that TiO₂ filler particles in the epoxy/bamboo and epoxy/flax composite will improve the tribological properties of the developed composites. Statistical analysis of SWR concludes that normal load is the most influencing factor, followed by sliding distance, Wt.% TiO2 filler and sliding velocity. ANOVA concludes that normal load has the maximum effect of 31.92% and 35.77% and Wt.% of TiO2 filler has the effect of 17.33% and 16.98%, respectively, on the SWR of bamboo and flax FRCs. A fairly good agreement between the Taguchi predictive model and experimental results is obtained.

This research paper attempts to include both TiO₂ filler and bamboo/flax fibers to develop a novel hybrid composite material. TiO₂ micro and nanoparticles are promising filler materials, it helps to enhance the mechanical and tribological properties of the epoxy composites. Taguchi DOE and ANOVA used for statistical analysis serve as guidelines for academicians and practitioners on how to best optimize the control variable with particular reference to natural FRCs.

The investigation aims to improve Nd: YAG laser technology for precision cutting of carbon fiber reinforcing polymers (CFRPs), specifically those containing newly created resin (NDR) from the polyethylene and polyurea group, is the goal of the study. The focus is on showing how Nd: YAG lasers may be used to precisely cut CFRP with NDR materials, emphasizing how useful they are for creating intricate and long-lasting components.

The study employs a systematic approach that includes complicated factorial designs, Taguchi L27 orthogonal array trials, Gray relational analysis (GRA) and machine learning predictions. The effects of laser cutting factors on CFRP with NDR geometry are investigated experimentally, with the goal of optimizing the cutting process for greater quality and efficiency. The approach employs data-driven decision-making with GRA, which improves cut quality and manufacturing efficiency while producing high-quality CFRP composites. Integration of machine learning models into the optimization process significantly boosts the precision and cost-effectiveness of laser cutting operations for CFRP materials.

The work uses Taguchi L27 orthogonal array trials for systematically explore the effects of specified parameters on CFRP cutting. The cutting process is then optimized using GRA, which identifies influential elements and determines the ideal parameter combination. In this paper, initially machining parameters are established at level L3P3C3A2, and the optimal machining parameters are determined to be at levels L3P2C3A3 and L3P2C1A2, based on predictions and experimental results. Furthermore, the study uses machine learning prediction models to continuously update and optimize kerf parameters, resulting in high-quality cuts at a lower cost. Overall, the study presents a holistic method to optimize CFRP cutting processes employing sophisticated techniques such as GRA and machine learning, resulting in better quality and efficiency in manufacturing operations.

The novel concept is in precisely measuring the kerf width and deviation in CFRP samples of NDR using sophisticated imaging techniques like SEM, which improves analysis and precision. The newly produced resin from the polyethylene and polyurea group with carbon fiber offers a more precise and comprehensive understanding of the material's behavior under different cutting settings, which makes it novel for kerf width and kerf deviation in their studies. To optimize laser cutting settings in real time while considering laser machining conditions, the study incorporates material insights into machine learning models.

This study aims to improve detection efficiency of fluorescence biosensor or a graphene field-effect transistor biosensor. Graphene field-effect transistor biosensing and fluorescent biosensing were integrated and combined with magnetic nanoparticles to construct a multi-sensor integrated microfluidic biochip for detecting single-stranded DNA. Multi-sensor integrated biochip demonstrated higher detection reliability for a single target and could simultaneously detect different targets.

In this study, the authors integrated graphene field-effect transistor biosensing and fluorescent biosensing, combined with magnetic nanoparticles, to fabricate a multi-sensor integrated microfluidic biochip for the detection of single-stranded deoxyribonucleic acid (DNA). Graphene films synthesized through chemical vapor deposition were transferred onto a glass substrate featuring two indium tin oxide electrodes, thus establishing conductive channels for the graphene field-effect transistor. Using π-π stacking, 1-pyrenebutanoic acid succinimidyl ester was immobilized onto the graphene film to serve as a medium for anchoring the probe aptamer. The fluorophore-labeled target DNA subsequently underwent hybridization with the probe aptamer, thereby forming a fluorescence detection channel.

This paper presents a novel approach using three channels of light, electricity and magnetism for the detection of single-stranded DNA, accompanied by the design of a microfluidic detection platform integrating biosensor chips. Remarkably, the detection limit achieved is 10 pm, with an impressively low relative standard deviation of 1.007%.

By detecting target DNA, the photo-electro-magnetic multi-sensor graphene field-effect transistor biosensor not only enhances the reliability and efficiency of detection but also exhibits additional advantages such as compact size, affordability, portability and straightforward automation. Real-time display of detection outcomes on the host facilitates a deeper comprehension of biochemical reaction dynamics. Moreover, besides detecting the same target, the sensor can also identify diverse targets, primarily leveraging the penetrative and noninvasive nature of light.