Search results

This paper aims to use redundant manipulators to solve the challenge of collision avoidance in construction operations such as welding and painting.

In this paper, a null-space-based task-priority adjustment approach is developed to avoid collisions. The method establishes the relative position of the obstacle and the robot arm by defining the “link space,” and then the priority of the collision avoidance task and the end-effector task is adjusted according to the relative position by introducing the null space task conversion factors.

Numerical simulations demonstrate that the proposed method can realize collision-free maneuvers for redundant manipulators and guarantee the tracking precision of the end-effector task. The experimental results show that the method can avoid dynamic obstacles in redundant manipulator welding tasks.

A new formula for task priority adjustment for collision avoidance of redundant manipulators is proposed, and the original task tracking accuracy is guaranteed under the premise of safety.

Gas-insulated switchgear (GIS) stands as a pivotal component in power systems, susceptible to partial discharge occurrences. Nevertheless, manual inspection proves labor-intensive, exhibits a low defect detection rate. Conventional inspection robots face limitations, unable to perform live line measurements or adapt effectively to diverse environmental conditions. This paper aims to introduce a novel solution: the GIS ultrasonic partial discharge detection robot (GBOT), designed to assume the role of substation personnel in inspection tasks.

GBOT is a mobile manipulator system divided into three subsystems: autonomous location and navigation, vision-guided and force-controlled manipulator and data detection and analysis. These subsystems collaborate, incorporating simultaneous localization and mapping, path planning, target recognition and signal processing, admittance control. This paper also introduces a path planning method designed to adapt to the substation environment. In addition, a flexible end effector is designed for full contact between the probe and the device.

The robot fulfills the requirements for substation GIS inspections. It can conduct efficient and low-cost path planning with narrow passages in the constructed substation map, realizes a sufficiently stable detection contact and perform high defect detection rate.

The robot mitigates the labor intensity of grid maintenance personnel, enhances inspection efficiency and safety and advances the intelligence and digitization of power equipment maintenance and monitoring. This research also provides valuable insights for the broader application of mobile manipulators in diverse fields.

The robot is a mobile manipulator system used in GIS detection, offering a viable alternative to grid personnel for equipment inspections. Comparing with the previous robotic systems, this system can work in live electrical detection, demonstrating robust environmental adaptability and superior efficiency.

The current methods for inspecting tall or deep structures such as towers, chimneys, silos, and wells suffer from certain constraints. Manual and assisted inspection methods including humans, drones, wall climbing robots, and others are either costly, have a limited operation time, or affected by field conditions, such as temperature and radiation. This study aims to overcome the presented challenges through a teleoperated soft continuum manipulator capable of inspecting tall or deep structures with high resolution, an unlimited operation time and the ability to use different arms of the manipulator for different environments and structure sizes.

The teleoperated manipulator uses one rotary and two tendon actuators to reach and inspect the interior of a tall (or deep) structure. A sliding part along the manipulator’s body (arm constrainer and tendon router) induces a variable-length bending segment, allowing an inspection camera to be placed at different distances from the desired location.

The experiments confirmed the manipulator’s ability to inspect different locations in the structure’s interior. The manipulator also demonstrated a submillimeter motion resolution vertically and a 2.5 mm per step horizontally. The inspection time of the full structure was 48.53 min in the step-by-step mode and was calculated to be 4.23 min in the continuous mode.

The presented manipulator offers several design novelties: the arm’s thin-wide cross-section, the variable-length bending segment in a fixed-length body, the external rolling tendon routing and the ability to easily replace the arm with another of different material or dimensions to suite different structures and environments.

To provide high torques needed to move a robot’s links, electric actuators are followed by a transmission system with a high transmission rate. For instance, gear ratios of 100:1 are often used in the joints of a robotic manipulator. This results into an actuator with large mechanical impedance (also known as nonback-drivable actuator). This in turn generates high contact forces when collision of the robotic mechanism occur and can cause humans’ injury. Another disadvantage of electric actuators is that they can exhibit overheating when constant torques have to be provided. Comparing to electric actuators, pneumatic actuators have promising properties for robotic applications, due to their low weight, simple mechanical design, low cost and good power-to-weight ratio. Electropneumatically actuated robots usually have better friction properties. Moreover, because of low mechanical impedance, pneumatic robots can provide moderate interaction forces which is important for robotic surgery and rehabilitation tasks. Pneumatic actuators are also well suited for exoskeleton robots. Actuation in exoskeletons should have a fast and accurate response. While electric motors come against high mechanical impedance and the risk of causing injuries, pneumatic actuators exhibit forces and torques which stay within moderate variation ranges. Besides, unlike direct current electric motors, pneumatic actuators have an improved weight-to-power ratio and avoid overheating problems.

The aim of this paper is to analyze a nonlinear optimal control method for electropneumatically actuated robots. A two-link robotic exoskeleton with electropneumatic actuators is considered as a case study. The associated nonlinear and multivariable state-space model is formulated and its differential flatness properties are proven. The dynamic model of the electropneumatic robot is linearized at each sampling instance with the use of first-order Taylor series expansion and through the computation of the associated Jacobian matrices. Within each sampling period, the time-varying linearization point is defined by the present value of the robot’s state vector and by the last sampled value of the control inputs vector. An H-infinity controller is designed for the linearized model of the robot aiming at solving the related optimal control problem under model uncertainties and external perturbations. An algebraic Riccati equation is solved at each time-step of the control method to obtain the stabilizing feedback gains of the H-infinity controller. Through Lyapunov stability analysis, it is proven that the robot’s control scheme satisfies the H-infinity tracking performance conditions which indicate the robustness properties of the control method. Moreover, global asymptotic stability is proven for the control loop. The method achieves fast convergence of the robot’s state variables to the associated reference trajectories, and despite strong nonlinearities in the robot’s dynamics, it keeps moderate the variations of the control inputs.

In this paper, a novel solution has been proposed for the nonlinear optimal control problem of robotic exoskeletons with electropneumatic actuators. As a case study, the dynamic model of a two-link lower-limb robotic exoskeleton with electropneumatic actuators has been considered. The dynamic model of this robotic system undergoes first approximate linearization at each iteration of the control algorithm around a temporary operating point. Within each sampling period, this linearization point is defined by the present value of the robot’s state vector and by the last sampled value of the control inputs vector. The linearization process relies on first-order Taylor series expansion and on the computation of the associated Jacobian matrices. The modeling error which is due to the truncation of higher-order terms from the Taylor series is considered to be a perturbation which is asymptotically compensated by the robustness of the control algorithm. To stabilize the dynamics of the electropneumatically actuated robot and to achieve precise tracking of reference setpoints, an H-infinity (optimal) feedback controller is designed. Actually, the proposed H-infinity controller for the model of the two-link electropneumatically actuated exoskeleton achieves the solution of the associated optimal control problem under model uncertainty and external disturbances. This controller implements a min-max differential game taking place between: (i) the control inputs which try to minimize a cost function which comprises a quadratic term of the state vector’s tracking error and (ii) the model uncertainty and perturbation inputs which try to maximize this cost function. To select the stabilizing feedback gains of this H-infinity controller, an algebraic Riccati equation is being repetitively solved at each time-step of the control method. The global stability properties of the H-infinity control scheme are proven through Lyapunov analysis.

Pneumatic actuators are characterized by high nonlinearities which are due to air compressibility, thermodynamics and valves behavior and thus pneumatic robots require elaborated nonlinear control schemes to ensure their fast and precise positioning. Among the control methods which have been applied to pneumatic robots, one can distinguish differential geometric approaches (Lie algebra-based control, differential flatness theory-based control, nonlinear model predictive control [NMPC], sliding-mode control, backstepping control and multiple models-based fuzzy control). Treating nonlinearities and fault tolerance issues in the control problem of robotic manipulators with electropneumatic actuators has been a nontrivial task.

The novelty of the proposed control method is outlined as follows: preceding results on the use of H-infinity control to nonlinear dynamical systems were limited to the case of affine-in-the-input systems with drift-only dynamics. These results considered that the control inputs gain matrix is not dependent on the values of the system’s state vector. Moreover, in these approaches the linearization was performed around points of the desirable trajectory, whereas in the present paper’s control method the linearization points are related with the value of the state vector at each sampling instance as well as with the last sampled value of the control inputs vector. The Riccati equation which has been proposed for computing the feedback gains of the controller is novel, so is the presented global stability proof through Lyapunov analysis. This paper’s scientific contribution is summarized as follows: (i) the presented nonlinear optimal control method has improved or equally satisfactory performance when compared against other nonlinear control schemes that one can consider for the dynamic model of robots with electropneumatic actuators (such as Lie algebra-based control, differential flatness theory-based control, nonlinear model-based predictive control, sliding-mode control and backstepping control), (ii) it achieves fast and accurate tracking of all reference setpoints, (iii) despite strong nonlinearities in the dynamic model of the robot, it keeps moderate the variations of the control inputs and (iv) unlike the aforementioned alternative control approaches, this paper’s method is the only one that achieves solution of the optimal control problem for electropneumatic robots.

The use of electropneumatic actuation in robots exhibits certain advantages. These can be the improved weight-to-power ratio, the lower mechanical impedance and the avoidance of overheating. At the same time, precise positioning and accurate execution of tasks by electropneumatic robots requires the application of elaborated nonlinear control methods. In this paper, a new nonlinear optimal control method has been developed for electropneumatically actuated robots and has been specifically applied to the dynamic model of a two-link robotic exoskeleton. The benefit from using this paper’s results in industrial and biomedical applications is apparent.

A comparison of the proposed nonlinear optimal (H-infinity) control method against other linear and nonlinear control schemes for electropneumatically actuated robots shows the following: (1) Unlike global linearization-based control approaches, such as Lie algebra-based control and differential flatness theory-based control, the optimal control approach does not rely on complicated transformations (diffeomorphisms) of the system’s state variables. Besides, the computed control inputs are applied directly on the initial nonlinear model of the electropneumatic robot and not on its linearized equivalent. The inverse transformations which are met in global linearization-based control are avoided and consequently one does not come against the related singularity problems. (2) Unlike model predictive control (MPC) and NMPC, the proposed control method is of proven global stability. It is known that MPC is a linear control approach that if applied to the nonlinear dynamics of the electropneumatic robot, the stability of the control loop will be lost. Besides, in NMPC the convergence of its iterative search for an optimum depends on initialization and parameter values selection and consequently the global stability of this control method cannot be always assured. (3) Unlike sliding-mode control and backstepping control, the proposed optimal control method does not require the state-space description of the system to be found in a specific form. About sliding-mode control, it is known that when the controlled system is not found in the input-output linearized form the definition of the sliding surface can be an intuitive procedure. About backstepping control, it is known that it cannot be directly applied to a dynamical system if the related state-space model is not found in the triangular (backstepping integral) form. (4) Unlike PID control, the proposed nonlinear optimal control method is of proven global stability, the selection of the controller’s parameters does not rely on a heuristic tuning procedure, and the stability of the control loop is assured in the case of changes of operating points. (5) Unlike multiple local models-based control, the nonlinear optimal control method uses only one linearization point and needs the solution of only one Riccati equation so as to compute the stabilizing feedback gains of the controller. Consequently, in terms of computation load the proposed control method for the electropneumatic actuator’s dynamics is much more efficient.

The purpose of this paper is to present a wall-climbing robot platform for heavy-load with negative pressure adsorption, which could be equipped with a six-degree of freedom (DOF) collaborative robot (Cobot) and detection device for inspecting the overwater part of concrete bridge towers/piers for large bridges.

By analyzing the shortcomings of existing wall-climbing robots in detecting concrete structures, a wall-climbing mobile manipulator (WCMM), which could be compatible with various detection devices, is proposed for detecting the concrete towers/piers of the Hong Kong-Zhuhai-Macao Bridge. The factors affecting the load capacity are obtained by analyzing the antislip and antioverturning conditions of the wall-climbing robot platform on the wall surface. Design strategies for each part of the structure of the wall-climbing robot are provided based on the influencing factors. By deriving the equivalent adsorption force equation, analyzed the influencing factors of equivalent adsorption force and provided schemes that could enhance the load capacity of the wall-climbing robot.

The adsorption test verifies the maximum negative pressure that the fan module could provide to the adsorption chamber. The load capacity test verifies it is feasible to achieve the expected bearing requirements of the wall-climbing robot. The motion tests prove that the developed climbing robot vehicle could move freely on the surface of the concrete structure after being equipped with a six-DOF Cobot.

The development of the heavy-load wall-climbing robot enables the Cobot to be installed and equipped on the wall-climbing robot, forming the WCMM, making them compatible with carrying various devices and expanding the application of the wall-climbing robot.

A heavy-load wall-climbing robot using negative pressure adsorption has been developed. The wall-climbing robot platform could carry a six-DOF Cobot, making it compatible with various detection devices for the inspection of concrete structures of large bridges. The WCMM could be expanded to detect the concretes with similar structures. The research and development process of the heavy-load wall-climbing robot could inspire the design of other negative-pressure wall-climbing robots.

Visual feedback control is a promising solution for robots work in unstructured environments, and this is accomplished by estimation of the time derivative relationship between the image features and the robot moving. While some of the drawbacks associated with most visual servoing (VS) approaches include the vision–motor mapping computation and the robots’ dynamic performance, the problem of designing optimal and more effective VS systems still remains challenging. Thus, the purpose of this paper is to propose and evaluate the VS method for robots in an unstructured environment.

This paper presents a new model-free VS control of a robotic manipulator, for which an adaptive estimator aid by network learning is proposed using online estimation of the vision–motor mapping relationship in an environment without the knowledge of statistical noise. Based on the adaptive estimator, a model-free VS schema was constructed by introducing an active disturbance rejection control (ADRC). In our schema, the VS system was designed independently of the robot kinematic model.

The various simulations and experiments were conducted to verify the proposed approach by using an eye-in-hand robot manipulator without calibration and vision depth information, which can improve the autonomous maneuverability of the robot and also allow the robot to adapt its motion according to the image feature changes in real time. In the current method, the image feature trajectory was stable in the camera field range, and the robot’s end motion trajectory did not exhibit shock retreat. The results showed that the steady-state errors of image features was within 19.74 pixels, the robot positioning was stable within 1.53 mm and 0.0373 rad and the convergence rate of the control system was less than 7.21 s in real grasping tasks.

Compared with traditional Kalman filtering for image-based VS and position-based VS methods, this paper adopts the model-free VS method based on the adaptive mapping estimator combination with the ADRC controller, which is effective for improving the dynamic performance of robot systems. The proposed model-free VS schema is suitable for robots’ grasping manipulation in unstructured environments.

Traditional robot arm trajectory planning methods have problems such as insufficient generalization performance and low adaptability. This paper aims to propose a method to plan the robot arm’s trajectory using the trajectory learning and generalization characteristics of dynamic motion primitives (DMPs).

This study aligns multiple demonstration motion primitives using dynamic time warping; use the Gaussian mixture model and Gaussian mixture regression methods to obtain the ideal primitive trajectory actions. By establishing a system model that improves DMPs, the parameters of the nonlinear function are learned based on the ideal primitive trajectory actions of the robotic arm, and the robotic arm motion trajectory is reproduced and generalized.

Experiments have proven that the robot arm motion trajectory learned by the method proposed in this article can not only learn to generalize and demonstrate the movement trend of the primitive trajectory, but also can better generate ideal motion trajectories and avoid obstacles when there are obstacles. The maximum Euclidean distance between the generated trajectory and the demonstration primitive trajectory is reduced by 29.9%, and the average Euclidean distance is reduced by 54.2%. This illustrates the feasibility of this method for robot arm trajectory planning.

It provides a new method for the trajectory planning of robotic arms in unstructured environments while improving the adaptability and generalization performance of robotic arms in trajectory planning.

The null-space projection method is commonly adopted for controlling redundant robots, which undoubtedly requires the robot Jacobian matrix inverse. This paper aims to provide a novel control scheme, which enables null-space control of redundant robots without conflict with the main task space.

In this paper, an impedance-based null-space control approach for redundant robots is proposed. The null-space degrees of freedom are separated from the primary task space by using the eigenvalue decomposition. Then, a joint impedance controller spans the null space and is reflected into the joint space to manage the redundancy. Finally, several experiments have been conducted to evaluate and validate the performance of the proposed approach in comparison with the null-space projection method under various situations.

Experiment results show that no significant differences were observed between the different filling eigenvalues in the proposed approach under different null-space dimensions and motion velocity. Besides, comparative experiment results demonstrate that the proposed method can achieve comparable results to the null-space projection method. Nevertheless, the suggested approach has benefits regarding the quantity of control parameters in addition to not requiring a Jacobian inverse. Notably, the performance of the proposed method will improve as the null-space dimension increases.

This study presents a new control method for redundant robots, which has advantages for dealing with the problems of controlling redundant robots compared to the existing methods.

Fast obstacle avoidance path planning is a challenging task for multijoint robots navigating through cluttered workspaces. This paper aims to address this issue by proposing an improved path-planning method based on the distorted space (DS) method, specifically designed for high-dimensional complex environments.

The proposed method, termed topology-preserved distorted space (TP-DS) method, mitigates the limitations of the original DS method by preserving space topology through elastic deformation. By applying distinct spring constants, the TP-DS autonomously shrinks obstacles to microscopic areas within the configuration space, maintaining consistent topology. This enhancement extends the application scope of the DS method to handle complex environments effectively.

Comparative analysis demonstrates that the proposed TP-DS method outperforms traditional methods regarding planning efficiency. Successful obstacle avoidance tasks in the cluttered workspace validate its applicability on a physical 6-DOF manipulator, highlighting its potential for industrial implementations.

The novel TP-DS method generates a topology-preserved collision-free space by leveraging elastic deformation and shows significant capability and efficiency in planning obstacle-avoidance paths in complex application scenarios.

In response to the issue of traditional algorithms often falling into local minima or failing to find feasible solutions in manipulator path planning. The purpose of this paper is to propose a 3D artificial moment method (3D-AMM) for obstacle avoidance for the robotic arm's end-effector.

A new method for constructing temporary attractive points in 3D has been introduced using the vector triple product approach, which generates the attractive moments that attract the end-effector to move toward it. Second, distance weight factorization and spatial projection methods are introduced to improve the solution of repulsive moments in multiobstacle scenarios. Third, a novel motion vector-solving mechanism is proposed to provide nonzero velocity for the end-effector to solve the problem of limiting the solution of the motion vector to a fixed coordinate plane due to dimensionality constraints.

A comparative analysis was conducted between the proposed algorithm and the existing methods, the improved artificial potential field method and the rapidly-random tree method under identical simulation conditions. The results indicate that the 3D-AMM method successfully plans paths with smoother trajectories and reduces the path length by 20.03% to 36.9%. Additionally, the experimental comparison outcomes affirm the feasibility and effectiveness of this method for obstacle avoidance in industrial scenarios.

This paper proposes a 3D-AMM algorithm for manipulator path planning in Cartesian space with multiple obstacles. This method effectively solves the problem of the artificial potential field method easily falling into local minimum points and the low path planning success rate of the rapidly-exploring random tree method.