Search results

The purpose of this paper is to evaluate the dosimetric properties of N-(3-methoxypropyl) acrylamide (NMPA) polymer gel dosimeter using UV-vis spectrophotometry as a simple and low-cost method.

The gel samples have been irradiated to various doses using a medical linear accelerator with 6 MV beam energy. The optical density of un-irradiated and irradiated NMPA polymer gel dosimeters in terms of absorbance at 500 nm was investigated by UV-vis spectrophotometry.

The absorbance values of the gel samples were increased linearly with increasing dose in the dose range between 2 and 20 Gy. A remarkable improvement in the dose response was noticed after the addition of various concentrations of glycerol. The impact of dose rate, beam energy and the post-stability of the exposed gels was studied and found consistent with the previous study using nuclear magnetic resonance results (energy independent and dose rate independent, stable up to one week).

The results of the independent experimental spectrophotometry and nuclear magnetic resonance analyses indicate that the NMPA polymer gel dosimeter has good and consistent dosimetric features for radiotherapy dosimetry.

The ionizing radiation-induced polymerization of gel samples leads to a change in the absorbance of the irradiated gel samples. This study introduces the first characterization of NMPA gel dosimeter by means of UV-vis spectrophotometer.

The vibration of the rails is a significant source of railway rolling noise, often forming the dominant component of noise in the important frequency region between 400 and 2000 Hz. The purpose of the paper is to investigate the influence of the ground profile and the presence of the train body on the sound radiation from the rail.

Two-dimensional boundary element calculations are used, in which the rail vibration is the source. The ground profile and various different shapes of train body are introduced in the model, and results are observed in terms of sound power and sound pressure. Comparisons are also made with vibro-acoustic measurements performed with and without a train present.

The sound radiated by the rail in the absence of the train body is strongly attenuated by shielding due to the ballast shoulder. When the train body is present, the sound from the vertical rail motion is reflected back down toward the track where it is partly absorbed by the ballast. Nevertheless, the sound pressure at the trackside is increased by typically 0–5 dB. For the lateral vibration of the rail, the effects are much smaller. Once the sound power is known, the sound pressure with the train present can be approximated reasonably well with simple line source directivities.

Numerical models used to predict the sound radiation from railway rails have generally neglected the influence of the ground profile and reflections from the underside of the train body on the sound power and directivity of the rail. These effects are studied in a systematic way including comparisons with measurements.

The malfunction variables of power stations are related to the areas of weather, physical structure, control and load behaviour. To predict temporal power failure is difficult due to their unpredictable characteristics. As high accuracy is normally required, the estimation of failures of short-term temporal prediction is highly difficult. This study presents a method for converting stochastic behaviour into a stable pattern, which can subsequently be used in a short-term estimator. For this conversion, K-means clustering is employed, followed by Long-Short-Term Memory (LSTM) and Gated Recurrent Unit (GRU) algorithms are used to perform the Short-term estimation. The environment, the operation and the generated signal factors are all simulated using mathematical models. Weather parameters and load samples have been collected as part of a data set. Monte-Carlo simulation using MATLAB programming has been used to conduct experimental estimation of failures. The estimated failures of the experiment are then compared with the actual system temporal failures and found to be in good match. Therefore, for any future power grid, there is a testbed ready to estimate the future failures.

The purpose of this study is to design a radio altimeter antenna whose production process is facilitated and can work with multiple-input multiple-output (MIMO) properties to provide space gain on the aircraft.

To create an easy-to-produce MIMO, a two-storied structure consisting of a reflector and a top antenna was designed. The dimensions of the reflector were prevented to get smaller to supply easy production. The unit cell nearly with the same dimensions of a lower frequency was protected through the original cell design. The co-planar structure with the use of a via connection was modified and a structure was achieved with no need to via for easy production, too. Finally, the antennas were placed side by side and the distance between them was optimized to achieve a MIMO operation.

As a result, an easy-to-produce, compact and successful radio altimeter antenna was obtained with high antenna parameters such as 10.14 dBi gain and 10.55 dBi directivity, and the conical pattern along with proper MIMO features, through original reflector surface and top antenna system.

Since radio altimeter antennas require high radiation properties, the microstrip antenna structure is generally used in literature. This paper contributes by presenting the radio altimeter application with antenna-reflective structure participation. The technical solutions were developed during the design, focusing on an easy manufacturing process for both the reflective surface and the upper antenna. Also, the combination of International Telecommunication Union’s recommended features that require high antenna properties was achieved, which is challenging to reach. In addition, by operating the antenna as a successful MIMO, two goals of easy production and space gain on aircraft have been attained at the same time.

The utilisation of renewable energy sources for generating electricity and potable water is one of the most sustainable approaches in the current scenario. Therefore, the current research aims to design and develop a novel co-generation system to address the electricity and potable water needs of rural areas.

The cogeneration system mainly consists of a solar parabolic dish concentrator (SPDC) system with a concentrated photo-voltaic module at the receiver for electricity generation. It is further integrated with a low-temperature thermal desalination (LTTD) system for generating potable water. Also, a novel corn cob filtration system is introduced for the pre-treatment to reduce the salt content in seawater before circulating it into the receiver of the SPDC system. The designed novel co-generation system has been numerically and experimentally tested to analyse the performance at Karaikal, U.T. of Puducherry, India.

Because of the pre-treatment with a corn cob, the scale formation in the pipes of the SPDC system is significantly reduced, which enhances the efficiency of the system. It is observed that the conductivity, pH and TDS of seawater are reduced significantly after the pre-treatment by the corncob filtration system. Also, the integrated system is capable of generating 6–8 litres of potable water per day.

The integration of the corncob filtration system reduced the scaling formation compared to the general circulation of water in the hoses. Also, the integrated SPDC and LTTD systems are comparatively economical to generate higher yields of clean water than solar stills.

This study aims to develop an extended social attachment model for expatriates, integrating a multiple stakeholder perspective, to understand evacuation decisions during disasters.

Through interviews with 12 Tokyo-based expatriates who experienced the 2011 Tohoku earthquake, tsunami and nuclear disasters, this study collects the lived experiences of a diverse set of expatriates. This data is analyzed abductively to map relevant evacuation factors and to propose a reaction typology.

While the 2011 Tohoku disasters caused regional destruction and fears of nuclear fallout, Tokyo remained largely unscathed. Still, many expatriates based in Tokyo chose to leave the country. Evacuation decisions were shaped by an interplay of threat assessment, location of attachment figures and cross-cultural adjustment. The study also discusses the influence of expatriate types.

Disaster planning is often overlooked or designed primarily with host country nationals in mind. Expatriates often lack the disaster experience and readiness of host country nationals in disaster-prone regions in Asia and beyond, and thus might need special attention when disaster strikes. This study provides advice for how to do so.

By unpacking the under-researched and complex phenomenon of expatriate reactions to disasters, this study contributes to the fields of international human resource and disaster management. Specifically, seven proposition on casual links leading to expatriate evacuation are suggested, paving the way for future research.

This paper aims to evaluate the hypothetical situation in a resembling airport to Esenboga Airport and analyzes the condition of all ground support equipment (GSE) equipment to be supplied by electricity produced by solar panels mounted on the rooftop of the terminal building. The case is discussed using environmental emissions and economic feasibility. The results of the resembling case can be generalized to all airports for the reduction of emissions caused by ground operations of aviation.

GSE fleet data which has been prepared by TGS operated in the Esenboğa Airport have been used to calculate emissions, and equivalent electricity consumption. A hypothetical solar panel construction on the rooftop of the terminal building and also the electricity production case was analyzed. Based on the calculations, both fuel and electricity use cases are compared by means of emissions and production costs using real data.

The electricity production and transmission pose a high value of emissions. Thus, electrification of GSE in the airport need a new approach such as producing the electric energy in the site. This research analyzes the case that the electricity is produced on the rooftop of terminal building and consumed by the GSE fleet. The authors discussed that it is both feasible and possible to electrify all the GSE except a shortage of two cold months with high fuel demand by using electric storage options.

Ground handling is performed by using GSE which is historically powered by diesel and such internal combustion engines which are well known for their high emission rates. As most of the airports reside in populated areas, GSE emissions need to be evaluated for reduction. However the electric energy could be an alternative for GSE emissions reduction

Aviation is a system of many subsystems in which the performance of each unit plays a crucial role in the final success of the system. Concerns on environmental protection make the aviation industry focus on reducing emissions produced during operations. Although aircraft emissions are widely discussed in the literature, ground handling systems which are an integral part of the whole aviation system, also need to be studied regarding the environmental issues. Besides, the European Union has set out targets of reducing emissions at the airports during ground operations to zero. This paper discusses the possibility of the target by comparing various scenarios

From a technological determinist perspective, machine learning (ML) may significantly contribute towards sustainable development. The purpose of this study is to synthesize prior literature on the role of ML in promoting sustainability and to encourage future inquiries.

This study conducts a systematic review of 110 papers that demonstrate the utilization of ML in the context of sustainable development.

ML techniques may play a vital role in enabling sustainable development by leveraging data to uncover patterns and facilitate the prediction of various variables, thereby aiding in decision-making processes. Through the synthesis of findings from prior research, it is evident that ML may help in achieving many of the United Nations’ sustainable development goals.

This study represents one of the initial investigations that conducted a comprehensive examination of the literature concerning ML’s contribution to sustainability. The analysis revealed that the research domain is still in its early stages, indicating a need for further exploration.

This research investigates the adoption of the industrial Internet of things (IIoT) in SMEs to achieve and increase organizational performance. With the latest technology, small and medium-sized enterprises (SMEs) can create a competitive edge in the market and better serve customers.

Twelve hypotheses are proposed for this study. This study constructed a questionnaire based on technological, organizational, environmental and human perspectives. A survey is conducted on the SMEs of India using the questionnaire.

Eight hypotheses were accepted, and four hypotheses were not supported. The hypotheses rejected are infrastructure, organizational readiness, internal excellence and prior experience. The findings suggested that adopting IIoT in SMEs will increase organizational performance.

This study will be helpful for the manager, top management and policymakers. This study identified the areas SMEs need to work on to adopt the technologies.

In the literature, no article considered IIoT adoption in SME firms as a human factor. Therefore, this study is unique, including human, technological, organizational and environmental factors.

The purpose of this paper is to provide a comprehensive review of a non-contact full-field optical measurement technique known as digital image correlation (DIC).

The approach of this review paper is to introduce the research pertaining to DIC. It comprehensively covers crucial facets including its principles, historical development, core challenges, current research status and practical applications. Additionally, it delves into unresolved issues and outlines future research objectives.

The findings of this review encompass essential aspects of DIC, including core issues like the subpixel registration algorithm, camera calibration, measurement of surface deformation in 3D complex structures and applications in ultra-high-temperature settings. Additionally, the review presents the prevailing strategies for addressing these challenges, the most recent advancements in DIC applications across quasi-static, dynamic, ultra-high-temperature, large-scale and micro-scale engineering domains, along with key directions for future research endeavors.

This review holds a substantial value as it furnishes a comprehensive and in-depth introduction to DIC, while also spotlighting its prospective applications.