Search results

Low performance life and increased machine downtime due to wear of resistance welding copper electrode is of major concern in fin–tube resistance welding in waste heat recovery boilers. The purpose of this study is to investigate an alternative material with good wear resistance to replace the currently utilized C11000 electrolytic tough pitch (ETP) copper electrode.

In this study, a Cu-Cr-Zr ternary alloy was developed for fin-to-tube welding electrode by melting commercial grade electrolytic copper (99.9% purity) plates, chips of chromium, powder of zirconium at 1100°–1300°C, followed by hot forging and precipitation hardening at 450°–550°C to attain appropriate grain flow. Microstructures of Cu-Cr-Zr alloys were analysed using scanning electron microscopy coupled with energy-dispersive backscatter electron spectrometry.

Wear performance of Cu-Cr-Zr and C11000 ETP Cu was evaluated using pin-on-disc set-up with Taguchi’s L₈ orthogonal array. Ranking of the parameters was done, and it was observed that the material and temperature play a very significant role in controlling the wear of an electrode.

Rate of fin–tube resistance welding was increased by 26% with Cu-Cr-Zr alloy. Further investigation on effect of plasma on the metallurgical characteristics of Cu-Cr-Zr is recommended.

Tribo-mechanical performance of newly developed Cu-Cr-Zr ternary alloy was compared with C11000 ETP copper.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-04-2023-0092/

The purpose of this study is to investigate the use of micro-pits technology to the problem of tribological performance in a sliding motion.

Vegetable oil is a sustainable and economically viable alternative to both mineral and synthetic oils, offering significant savings in both the cost of research and manufacturing. To solve the depriving issue and boost lubrication film thickness, the micro-pits on the surface may function as reservoirs that provide the oil to the contact inlet area. In this research, an aluminium block is used as the workpiece material in an evaluation of a through pin-on-disc tribotester. Lubricating oil in the form of super olein (SO) was used in the experiment.

The results show that the friction performance during a rubbing process between a hemispherical pin and an aluminium block lubricated with SO using aluminium alloy materials, AA5083, was significantly improved.

In this study, a material that breaks down called SO, which is derived from the fractionation of palm olein, was used to use a modified aluminium micro-pit sample that will serve as a lubricant reservoir in pin-on-disc tribotester.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-07-2023-0200/

This paper aims to compare the wear behavior, surface roughness, friction coefficient and volume loss of high-velocity oxy-fuel (HVOF) sprayed WC–Co and WC–Cr₃C₂–Ni coatings on AISI 1095 steel with spraying times of 10 and 15 s.

In this study, the pin-on-disc testing technique was used to evaluate the wear characteristics at a speed of 0.24 m/s, load of 40 N and test time of 60 min under dry conditions at room temperature. The wear characteristics were examined and analyzed by scanning electron microscopy and energy dispersive X-ray spectroscopy. The surface roughness of a coated surface was measured, and microhardness measurements were performed on the cross-sectioned and polished surfaces of the coating.

Spraying time and powder material affected the hardness of HVOF coatings due to differences in the porosity of the coated layers. The average hardness of the WC–Cr₃C₂–Ni coating with a spaying time of 15 s was approximately 14% higher than that of the WC–Cr₃C₂–Ni coating with a spraying time of 10 s. Under an applied load of 40 N, the WC–Co coating with a spraying time of 15 s had the lowest variation in the friction coefficient compared with the other coatings. The WC–Co coating with a spraying time of 10 s had the lowest average and variation in volume loss compared to the other coatings. The WC–Cr₃C₂–Ni coating with a spraying time of 10 s exhibited the highest average volume loss. The wear features changed slightly with the spraying time owing to variations in the hardness and friction coefficient.

This study investigated tribological performance of WC–Co; WC-Cr₃C₂-Ni coatings with spraying times of 10 and 15 s using pin-on-disc tribometer by rotating the relatively soft pin (C45 steel) against hard coated substrate (disc).

The purpose of this study is to look into the hygroscopic and tribo-mechanical properties of a polypropylene/polyamide-6 (PP/PA6) blend and a PP/PA6/Boron sesquioxide composite.

The hygroscopic behaviour of the PP/PA6 blend and PP/PA6/Boron sesquioxide composite was studied using a water contact angle goniometer in this study. To validate the hygroscopic behaviour of the blend and composite, water contact angles and surface energy of the materials were investigated. Tensile strength and hardness tests were used to determine mechanical characteristics, and tribological experiments on a pin-on-disc tribometer were used to demonstrate the friction and wear rates of dry and water-conditioned blends and composites. The melting temperature of dry and water-conditioned composites was determined using DSC analysis.

The hygroscopic effect of the PP/PA6 blend was found to be minimal in the experiment, while it was relatively dominating in the PP/PA6/Boron sesquioxide composite. Tensile strength was found to be somewhat lower in blend and composite compared to virgin PP, whereas hardness was found to be higher in both blend and composite. The composite’s tribological testing findings were fairly outstanding, with the coefficient of friction (COF) and wear rates significantly reduced due to boron sesquioxide reinforcement. The reaction between boron sesquioxide and water molecules produced boric acid, which increased the tribological characteristics of the composite even further. Following 30 days of water conditioning, the weight of the blend increased by 3.64% and the weight of the composite increased by 6.45% as compared to the dry materials. After water conditioning, tensile strength reduced by 0.8% for the blend and 14.16% for the composite. Hardness was determined to be the same in the dry state and after water-conditioning for blend but dropped 1% for composite. As compared to blend, the COF and wear resistance of composite were 15.52% and 25.16% higher, respectively. After absorbing some water, the results increased to 28.57% and 34.9%, respectively.

The mechanical and thermal behaviour of polymer composites (particularly polyamide composites) vary depending on the surrounding environment. Tests were carried out to explore the effect of water treatment on the tribo-mechanical and thermal characteristics of PP/PA6/Boron sesquioxide composite. Water treatment caused polyamides to bind with water molecules, resulting in voids in the material. The interaction between boron sesquioxide and water molecules produced boric acid, which increased the tribological characteristics of the composite.

Studies on this topic have shown the remarkable lubricating properties, viz. friction-reducing and anti-wear, of certain nanoparticles. This makes them potential candidates for replacing the lubrication additives currently used in automobile lubricants, especially because the latter is known to be pollutants and less efficient in some specific conditions. This has not gone unnoticed to professionals in the sector, including those commercializing these additives, the oil companies and the car industry, all of whom are following this burgeoning research area with keen interest. All of them are faced with the problem of providing lubricants that meet the needs of the technological evolution of engines while respecting ever-stricter environmental norms.

The impact of copper oxide (CuO) and zinc oxide (ZnO) nanoparticles on the tribological properties of the SAE-40 pure diesel oil is studied in this paper. The two nanoparticles are not oxide or deteriorate with the base oil. The average size of CuO and ZnO nanoparticles is 40 and 20 nm, respectively. Nanoparticle concentrations of 0.1 Wt.%, 0.2 Wt.%, 0.3 Wt.%, 0.4 Wt.% and 0.5 Wt.% are tested using a pin-on-disk tribometer to evaluate their impact on friction and wear. The test is carried out at different loads and rotating speeds of 58.86 N and 300 rpm, 39.24 N and 500 rpm and 78.48 N and 900 rpm at room temperature, respectively.

The obtained results of the nanolubricants are compared with those of pure diesel oil in terms of % improvement in tribological properties. However, it is observed that an increase in the nanoparticle concentrations does not guarantee to enhance the tribological properties. Similarly, increasing the applied load and the rotating speed does not lead to improving the anti-friction and anti-wear properties. The results obtained revealed that the optimal improvements in the anti-friction and anti-wear properties of the pure oil are 69% and 77% when CuO nanoparticle concentrations of 0.3 Wt.% and the ZnO nanoparticle concentrations of 0.1 Wt.% are used, where the applied load and rotating speed are 39.24 N and 500 rpm, respectively. It has also been noticed that the CuO nanolubricants have a significant impact on the anti-friction property compared with ZnO nanolubricants.

All these nanoparticles have been the subject of detailed investigation in this research and many key issues have been tackled, such as the conditions leading to these properties, the lubrication mechanisms coming into play, the influence of parameters such as size, structure and morphology of the nanoparticles on their tribological properties/lubrication mechanisms and the interactions between the particles and the lubricant co-additives. To answer such questions, state-of-the-art characterization techniques are required, often in situ, and sometimes an extremely complex set up. Some of these can even visualize the behavior of a nanoparticle in real time during a tribological test. The research on this topic has given a good understanding of the way these nanoparticles behave, and we can now identify the key parameters to be adjusted when optimizing their lubrication properties.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-08-2022-0234/

This study aims to investigate the surface modification on 20CrMnTi gear steel individually treated by diamond-like carbon films and nitride coatings.

For this purpose, the mechanical properties of a-C:H, ta-C and AlCrSiN coatings are characterized by nano-indentation and scratch tests. The friction and wear behaviors of these three coatings are evaluated by ball-on-disc tribological experiments under dry contact conditions.

The results show that the a-C:H coating has the highest coating-substrate adhesion strength (495 mN) and the smoothest surface (Ra is about 0.045 µm) compared with the other two coatings. The AlCrSiN coating shows the highest mean coefficient of friction (COF), whereas the ta-C coating exhibits the lowest one (steady at about 0.16). The carbon-based coatings possess excellent self-lubricating properties compared with nitride ceramic ones, which effectively reduce the COF by about 64%. The major failure mode of carbon-based coatings in dry contact is slight abrasive wear. The damage of AlCrSiN coating is mainly adhesive wear and abrasive wear.

It is suggested that the carbon-based film can effectively improve the friction-reducing and wear resistance performance of the gear steel surface, which has a promising application prospect in the mechanical transmission field.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-05-2023-0129/

The purpose of this study is to investigate the influence of surface texture on the subsurface characteristics of contact interfaces under elastohydrodynamic lubrication condition. As a typical contact form of gears and bearings, the optimization of friction characteristics at the elastohydrodynamic lubrication (EHL) interface has attracted the attention of scholars. Laser surface texturing is a feasible optimization solution, but there have been concerns about whether the surface texture of high-pair parts will affect their fatigue life.

To examine the impact of texture preparation on the subsurface characteristics of high-pair interfaces under EHL conditions, a point contact EHL model is developed that takes into account the effect of textured surface topography. The pressure and thickness of the oil film are calculated as input parameters under different loads and entrainment velocities. The finite element method is used to simulate the impact of textures with varying diameters, densities and depths on the subsurface characteristics of the elastohydrodynamic interface. According to ISO 25178, analyze the relationship between 3D topography parameters and subsurface characteristics and study the trend of friction characteristics and subsurface characteristics based on the results of the ball on disc friction tests.

The outcomes suggest that under different rotational velocity and load conditions, the textured surfaces exhibit improved friction reduction effects; however, the creation of textures can result in significant subsurface plastic deformation and local peeling. The existence of texture makes the larger stress zone in the subsurface layer closer to the surface, leading to fatigue failure near the surface. Reasonable design parameters can help enhance the attributes of the subsurface. A smaller Sa and a Str greater than 0.5 can achieve ideal subsurface properties on the textured surface.

This paper investigates the influence of surface texture on the friction and subsurface characteristics of EHL interfaces and analyzes the impact of surface texture on interface contact performance while achieving lubrication improvement functional characteristics. The results provide theoretical support for the optimization design and functional regulation of surface texture in EHL interfaces.

The peer review history for this article is https://publons.com/publon/10.1108/ILT-10-2023-0324/

The purpose of current study deals with the development and wear testing of jute and cotton fiber reinforced with nano fly ash-based epoxy composites. Performance of waste cotton fabric nano hybrid composites are compared with waste jute fabric nano hybrid composites.

Basic hand layup technique was used to develop composites. To optimize the parameters and design of experiments, Taguchi design was implemented to test wear rate and co-efficient of friction as per ASTM standards. Performance of waste cotton fabric nano hybrid composites is compared with waste jute fabric nano hybrid composites.

Result shows that nano fly ash lowers the wear rate and co-efficient of friction in developed composites. Findings reveals that hybrid composites of waste jute Fabric with 3 Wt.% of nano fly ash performed best amongst all composites developed. Morphology of nano composites worn out surfaces are also analyzed through SEM.

Practically, textile waste, i.e. jute, cotton and nano fly ash (thermal power plant) all wastes, is used to develop composites for multi-function application.

Wastes are reused and recycled to develop epoxy-based composites for sustainable structures in aviation.

To the best of the authors’ knowledge, nano fly ash and jute, cotton combination is used for the first time to develop and test for wear application.

This paper aims to explore the influence of applied pressure on the tribological properties of the friction component in a wet multi-disc clutch during the running-in process.

The running-in evolutionary was explored in terms of global friction performance. The variation of friction torque and mean COF of the initial 300 engagement cycles was obtained by full-scale tests. Finally, an optical microscope was used to detect the wear characteristics of friction surfaces.

The applied pressure showed a significant influence on the tribological behaviors of wet clutches during the running-in process. The mean COF decreased and then increases with the increase of the applied pressure. A higher applied pressure contributed to more asperity summits being sheared, thus resulting in a smoother surface. Considering a suitable wore performance, properly applied pressure is necessary.

The results provide theoretical guidance for selecting the optimal applied pressure in the running-in of wet clutches.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-08-2022-0256/

The purpose of this paper is to examine the mechanical characteristics and optimization of wear parameters of hybrid (TiO₂ + Y₂O₃) nanoparticles with Al matrix using squeeze casting technique.

The hybrid aluminium matrix nanocomposites (HAMNCs) were fabricated with varying concentrations of titanium oxide (TiO₂) and yttrium oxide (Y₂O₃), from 2.5 to 10 Wt.% in 2.5 Wt.% increments. Dry sliding wear test variables were optimized using the Taguchi method.

The introduction of hybrid nanoparticles in the aluminium (Al) matrix was evenly distributed in contrast to the base matrix. HAMNC6 (5 Wt.% TiO₂ + 5 Wt.% Y₂O₃) reported the maximum enhancement in mechanical properties (tensile strength, flexural strength, impact strength and density) and decrease in porosity% and elongation% among other HAMNCs. The results showed that the optimal combination of parameters to achieve the lowest wear rate was A3B3C1, or 15 N load, 1.5 m/s sliding velocity and 200 m sliding distance. The sliding distance showed the greatest effect on the dry sliding wear rate of HAMNC6 followed by applied load and sliding velocity. The fractured surfaces of the tensile sample showed traces of cracking as well as substantial craters with fine dimples and the wear worn surfaces were caused by abrasion, cracks and delamination of HAMNC6.

Squeeze-cast Al-reinforced hybrid (TiO₂+Y₂O₃) nanoparticles have been investigated for their impact on mechanical properties and optimization of wear parameters.