Search results

The purpose of this paper is to conduct an experimental investigation on the shock cell structure of jets emanating from a four-lobed corrugated nozzle using Schlieren imaging technique.

The Schlieren images were captured for seven different nozzle pressure ratios (NPR = 2, 3, 4, 5, 6, 7 and 8) and compared with the shock cell structure of a round nozzle with an identical exit area. The variation in the length of the shock cell, width of boundary interaction between adjacent shock cells, maximum width of first shock cell, Mach disk position and diameter for different NPR was measured from the Schlieren images and analysed.

A three-layer shock net observed in the jet emanating from the four-lobed corrugated nozzle is a novel concept in the field of under-expanded jet flows. A shock net represents interconnected layers of shock cells developed because of the interaction between the core and peripheral shock waves in a jet emanating from a corrugated lobed nozzle. Also, the pattern of shock net is different while taking Schlieren images across the groove and lobe sections. Thus, the shock net emerging from a corrugated lobed nozzle varies azimuthally and primarily depends on the nozzle exit cross section. The length of the shock cell, width of boundary interaction between adjacent shock cells, maximum width of first cell, Mach disk position and diameter were found to exhibit increasing trend with NPR.

A novel concept of interconnected layers of shock waves defined as “shock net” developed from a single jet emanating from a four-lobed corrugated nozzle was observed.

The purpose of this study is to investigate the aerodynamic characteristics of subsonic jet emanating from corrugated lobed nozzle.

Numerical simulations of subsonic turbulent jets from corrugated lobed nozzles using shear stress transport k-ω turbulence model have been carried out. The analysis was carried out by varying parameters such as lobe length, lobe penetration and lobe count at a Mach number of 0.75. The numerical predictions of axial and radial variation of the mean axial velocity, u′u′ ¯ and v′v′ ¯ have been compared with experimental results of conventional round and chevron nozzles reported in the literature.

The centreline velocity at the exit of the corrugated lobed nozzle was found to be lower than the velocity at the outer edges of the nozzle. The predicted potential core length is lesser than the experimental results of the conventional round nozzle and hence the decay in centreline velocity is faster. The centreline velocity increases with the increase in lobe length and becomes more uniform at the exit. The potential core length increases with the increase in lobe count and decreases with the increase in lobe penetration. The turbulent kinetic energy region is narrower with early appearance of a stronger peak for higher lobe penetration. The centreline velocity degrades much faster in the corrugated nozzle than the chevron nozzle and the peak value of Reynolds stress appears in the vicinity of the nozzle exit.

The corrugated lobed nozzles are used for enhancing mixing without the thrust penalty inducing better acoustic benefits.

The prominent features of the corrugated lobed nozzle were obtained from the extensive study of variation of flow characteristics for different lobe parameters after making comparison with round and chevron nozzle, which paved the way to the utilization of these nozzles for various applications.

This paper aims to present the jet mixing effectiveness of triangular tabs with semi-circular corrugations to control the subsonic and sonic correctly expanded jets.

Three semi-circular corrugated triangular tabs (Tab A, Tab B and Tab C) of equal blockage 5.11% are used, in which the corrugation locations on the tabs are varied. The offset distance between the semi-circular corrugations at the leaned edges of the triangular tabs are 0.0, 0.75 and 1.5 mm for the Tabs A, B and C, respectively. Two identical semi-circular corrugated tabs has been placed exactly 180° apart at the exit of the convergent nozzle. The pitot pressure measurements were taken to study the jet mixing characteristics of the tabs for the jet exit Mach numbers of 0.6, 0.8 and 1.0, and it is compared with the free jet.

The jet centerline pitot pressure decay reveals that, Tab A is very effective than Tab B and Tab C. For the jet exit Mach numbers of 0.6, 0.8 and 1.0, the potential core reduction for the Tab A is found to be 69.1%, 69.7% and 70.8%, respectively, when compared with the free jet.

The semi-circular corrugated triangular tabs were found to be more effective than the plain triangular tabs of equal blockage ratio for reducing the core length with minimum thrust loss.

The offset distance of the semi-circular corrugations are varied along the leaned sides of the triangular tabs, which is the novelty of this study.

An innovative hush kit for noisy jet aircraft with “old technology” low bypass engines (50 per cent of operating jets) is now being marketed within the aircraft industry. The objective of the marketing campaign is to entice the most appropriate sponsor or partner to team up with the hush kit's inventor Captain Thomas Friedrich.

1. Aircraft Noise—Its effect on people OF all the environmental noise sources, aircraft noise has received the most notoriety over the longest period of time. Aircraft noise is generally assumed to be a product of the jet age, but in 1939 in the United Kingdom, the Gorrell Committee on Control of Flying gave noise control the highest priority. However, it was not until post‐World War II that the public became disturbed by the continued high level of military aircraft operations, and this disturbance was aggravated by the rapid introduction of jet‐powered aircraft. Civil aviation developed rapidly and, as airports increased in size, and as aircraft movements doubled every five years, the surrounding communities expanded to the airport boundaries. These conditions of growth provided the ingredients for the aircraft noise problem. In the United Kingdom, all the major airports grew from military installations where little regard had been given to the environmental impact of these sites on the surrounding communities.

This paper aims to describe the numerical simulation of a three‐dimensional turbulent free jet issuing from a sharp‐edged equilateral triangular orifice into still air.

The numerical simulation was carried out by solving the governing three‐dimensional Reynolds‐averaged Navier‐Stokes equations. Several two‐equation eddy‐viscosity models (i.e. the standard k‐ε, renormalization group (RNG) k‐ε, realizable k‐ε, shear‐stress transport (SST) k‐ω), as well as the Reynolds stress models (i.e. the standard RSM and the SSG) were tested to simulate the flowfield. The numerical predictions were compared with experimental data in order to assess the capability and limitations of the various turbulent models examined in this work. Findings –The vena contracta effect was predicted by all the tested models. Among the eddy‐viscosity models only the realizable k‐ε model showed good agreement of the near‐field jet decay. None of the eddy‐viscosity models was capable of predicting the profiles of the jet turbulence intensities. The RSMs, especially the standard RSM, were able to produce much better predictions of the features of the jet in comparison with the eddy‐viscosity models. The standard RSM predictions were found to agree reasonably well with the experimental data.

The conclusion, that among the tested RANS turbulence closure models, the RSM appeared the only one capable of reproducing reasonably well the experimental data concerns only the jet flow case examined here. Also, the average computational time for a single run was quite long, i.e. 340 h, but it is believed that parallel computing will reduce it considerably.

The numerical results reported in this paper provide a comparison between several RANS turbulence closure models for simulating a turbulent free jet issuing from an equilateral triangular nozzle.

Control over large-scale coherent structures and stream-wise vortices lead to enhanced entrainment/conservation of the jet which is desirable for most free jet applications such as design of combustion chamber in jet engines and flame length elongation of welding torch used for metal cutting.

A co-flow nozzle with lip thickness of 2 mm, between the primary (inner) and secondary (outer) flow, is selected. Three nozzle combinations are used, i.e. C–C (circle–circle), C–E (circle–ellipse) and C–S (circle–square) for acquiring comparative data. For these nozzle combinations, inner nozzle exit plane is kept as a circle, whereas the outer nozzle exit planes are varied to circle, ellipse and square. The exit plane area of outer nozzle for the nozzle combinations has equivalent diameter, D_e. The nozzles are fabricated in a way that the outer nozzle can be rotated along the longitudinal axis, keeping the inner nozzle intact.

The C–C nozzle combination is effective in low Mach number regime in decaying the jet, when the rotational component is introduced. Around 30% reduction in the jet core length is observed for the C–C nozzle combinations without any lip. The C–E nozzle shows sedative result in decaying or preserving the jet. The C–S nozzle combination shows interesting phenomenon, whereby the low subsonic case tends to conserve the jet by 15% and the higher subsonic case tends to decay the jet by 10%.

The developed nozzle systems show both conservative and destructive effect on the jet, which is desirable for the mentioned applications.

Turbulent mixing of two co‐axial jets having a low annular to core area ratio is enhanced by employing a chute mixer, directing part of the annular stream at 10° towards the core region. Aims to present results from measurements of time‐averaged and fluctuating components of velocity under cold flow conditions.

Experiments were conducted at a bypass ratio of 0.47 which is a typical value for low bypass turbofan engines. Contours of time‐averaged velocity and streamwise and transverse turbulence intensities were obtained by making detailed measurements close to the chutes. Distributions of time‐averaged velocity and turbulence intensity were obtained at different axial locations downstream of the chute mixer. Total and static pressure measurements were also performed.

The high velocity annular stream was found to quickly diffuse after entering through the chutes and mix with the core stream due to high turbulence generation. A strong transverse turbulence component enhanced the mixing of the streams. With the aid of the chute mixer, nearly complete mixing is achieved over a length of 5 duct radii. A higher total pressure loss of about 1.38 percent is the penalty paid for the enhanced mixing.

Provides results from experiments into the process of turbulent mixing of co‐axial jets.

This paper aims to study passive control techniques for transonic flow over a backward-facing step (BFS) using square-lobed trailing edges. The study investigates the efficacy of upward and downward lobe patterns, different lobe widths and deflection angles on flow separation, aiming for a deeper understanding of the flow physics behind the passive flow control system.

Large Eddy Simulation and Reynolds-averaged Navier–Stokes were used to evaluate the results of the study. The research explores the impact of upward and downward patterns of lobes on flow separation through the effects of different lobe widths and deflection angles. Numerical methods are used to analyse the behaviour of transonic flow over BFS and compared it to existing experimental results.

The square-lobed trailing edges significantly enhance the reduction of mean reattachment length by up to 80%. At Ma = 0.8, the up-downward configuration demonstrates increased effectiveness in reducing the root mean square of pressure fluctuations at a proximity of 5-step height in the wake region, with a reduction of 50%, while the flat-downward configuration proves to be more efficient in reducing the root mean square of pressure fluctuations at a proximity of 1-step height in the near wake region, achieving a reduction of 71%. Furthermore, the study shows that the up-downward configuration triggers early spanwise velocity fluctuations, whereas the standalone flat-downward configuration displays less intense crosswise velocity fluctuations within the wake region.

The findings demonstrate the effectiveness of square-lobed trailing edges as passive control techniques, showing significant implications for improving efficiency, performance and safety of the design in aerospace and industrial systems.

This paper demonstrates that the square-lobed trailing edges are effective in reducing the mean reattachment length and pressure fluctuations in transonic conditions. The study evaluates the efficacy of different configurations, deflection angles and lobe widths on flow and provides insights into the flow physics of passive flow control systems.

RELATED to a degree and overlapping in their effects on the world's airline fleets, the issues of ageing and noise were addressed at a recent Avmark conference which was sponsored by FFV Aerotech. The problems of dealing economically with a large number of unacceptably noisy aircraft and ensuring that older aircraft remain airworthy beyond their original design lives are critical issues challenging operators throughout the world. Dominant here are the contributions dealing specifically with engine and airframe problems and solutions.