Search results

Purpose – This work aims to study the treatment of adsorbant on the increasing liquid hydrocarbon quality produced by pyrolysis low density polyethylene (LDPE) plastic waste at low temperature. The hydrocarbon distribution, physicochemical properties and emission test were also studied due to its application in internal combustion engine. This research uses pure Calcium carbonate (CaCO₃) and pure activated carbon as adsorbant, LDPE type clear plastic samples with control variable that is solar gas station.

Design/Methodology/Approach – LDPE plastic waste of 10 kg were vaporized in the thermal cracking batch reactor using LPG 12 kg as fuel at range temperature from 100 to 300°C and condensed into liquid hydrocarbon. Furthermore, this product was treated with the mixed CaCO₃ and activated carbon as adsorbants to decrease contaminant material.

Findings – GC-MS identified the presence of carbon chain in the range of C6–C44 with 24.24% of hydrocarbon compounds in the liquid. They are similar to diesel (C6–C14). The 30% of liquid yields were found at operating temperature of 300°C. The calorific value of liquid was 46.021 MJ/Kg. This value was 5.07% higher than diesel as control.

Originality/Value – Hydrocarbon compounds in liquid produced by thermal cracking at a low temperature was similar to liquid from a catalytic process.

Purpose – The purpose of this research is to synthesize modified thermoplastic sago starch (TPS) through in-situ mechanism by reacting sago starch with diphenylmethanediisocyanate (MDI) and castor oil simultaneously, resulting in a more homogenous and finer-sized polyurethane prepolymer (PUP).

Design/Methodology/Approach – The methods used were Thermal Gravimetric Analysis (TGA) and Differential Scanning Calorimetry (DSC) for thermal characterization and stability of PUP, modified TPS non-extracted and extracted with toluene and water.

Findings – TGA test results presented shows that PUP begins to decompose thermally at a temperature of 300–500 °C. Weight loss occurs rapidly between these temperatures and is completely discharged at a temperature of 500°C, which is called weight loss transition.

Research Limitations/Implications – When extracted with toluene and a water solvent, the melting point and latent heat of fusion slightly decreased; however, it is still higher than the original value of sago. In terms of thermal stability, modified TPS decomposes and loses weight at 150–200 °C in small quantities, continues with weight loss rapidly, and is completely discharged at 500°C. The thermal stability is considered high; thus, modified TPS application can be varied.

Practical Implications – DSC analysis and TGA shows that modified TPS has good thermal characteristics and thermal stability. Modified TPS has a melting point of 104.69°C, and the latent heat of fusion (ΔH) is 234.27 J/g. This value is close to the PUP melting point and latent heat of fusion, which reveals the formation of cross-link between the starch and PUP.

Purpose – This purpose of the research is to investigate the process of manufacturing LDPE recycle thermoplastic composites with reinforcement oil palm empty fruit bunch (OPEFB) biomass microfillers.

Design/Methodology/Approach – Methods of physical and chemical modification of OPEFB fibers into the LDPE matrix and the addition of some compatibilizer such as MAPE and xylene process through melt blending can improve mechanical properties, electrical properties, biodegradability, and improve the morphology of composites.

Research Limitations/Implications – These composites are prepared by the following matrix ratio: filler (70:30)% and filler size (63, 75, 90, and 106) μm. The LDPE plastic is crushed to a size of 0.5–1 cm, then pressed with hot press free heating for 5 min and with a pressure of 10 min at 145 °C. Based on the characterization obtained, the tensile strength and the high impact on the use of 106 μm filler is 13.86 MPa and 3,542.6 J/m², and thermal stability indicates the degradation temperature (T₀) 497.83 °C. FT-IR analysis shows the presence of functional groups of cellulose and lignin molecules derived from TKKS collected in the composite.

Practical Implications – Based on the characterization obtained, this composite can be applied as furniture material and vehicle dashboard.

Originality/Value – Composites obtained from recycle of LDPPE plastics waste has some advantages such as good compatibility and high tensile strength. This composite used the OPEFB filler whose size is in micrometer, and so this product is different from other products.