Search results

This study aims to observe the coloring efficacy of graphite (G) and nano bentonite clay (BCNPs) on the adsorption of Basic Blue 5 dye from residual dye bath solution.

Some factors that affected the adsorption processes were examined and found to have significant impacts on the adsorption capacity such as the initial concentration of G and/or BCNPs (Co: 40–2,320 mg/L), adsorbent bath pH (4–9), shaking time (30–150 min.) and initial dye concentration (40–200 mg/L). The adsorption mechanism of dye by using G and/or BCNPs was studied using two different models (first-pseudo order and second-pseudo order diffusion models). The equilibrium adsorption data for the dye understudy was analyzed by using four different models (Langmuir, Freundlich, Temkin modle and Dubinin–Radushkevich) models.

It has been found that the adsorption kinetics follow rather a pseudo-first-order kinetic model with a determination coefficient (R²) of 0.99117 for G and 0.98665 for BCNPs. The results indicate that the Freundlich model provides the best correlation for G with capacities q_max = 2.33116535 mg/g and R² = 0.99588, while the Langmuir model provides the best correlation for BCNPs with R² = 0.99074. The adsorbent elaborated from BCNPs was found to be efficient and suitable for removing basic dyes rather than G from aqueous solutions due to its availability, good adsorption capability, as well as low-cost preparation.

There is no research limitation for this work. Basic Blue 5 dye graphite (G) and nano bentonite clay (BCNPs) were used.

This work has practical applications for the textile industry. It is concluded that using graphite and nano bentonite clay can be a possible alternative to adsorb residual dye from dye bath solution and can make the process greener.

Socially, it has a good impact on the ecosystem and global community because the residual dye does not contain any carcinogenic materials.

The work is original and contains value-added products for the textile industry and other confederate fields.

Herein, this study aims to use our recently tailored and fully characterized poly acrylonitrile (AN)-starch nanoparticle graft copolymer having 60.1 graft yield percentage as a starting substrate for copper ions removal from wastewater effluent after chemical modification with hydroxyl amine via oximation reaction as a calorimetric sensor.

The calorimetric sensor batch technique was used to determine the resin's adsorption capacity, while atomic adsorption spectrometry was used to determine the residual copper ions concentration in the filtrate before and after adsorption. This was done to convert the copolymer's abundant nitrile groups into amidoxime groups, and the resulting poly (amidoxime) resin was used as a copper ion adsorbent. To validate the existence of amidoxime groups, the resin was qualitatively characterized using a rapid vanadium ion test and instrumentally using Fourier transform infrared spectroscopy spectra and scanning electron microscopy morphological analysis.

At pH 7, 400 ppm copper ions concentration and 0.25 g adsorbent at room temperature, the overall adsorption potential of poly (amidoxime) resin was found to be 115.2 mg/g. The process's adsorption, kinetics and isothermal analysis were examined using various variables such as pH, contact time, copper ion concentration and adsorbent dose. To pretend the adsorption kinetics, various kinetics models, including pseudo-first-order and pseudo-second-order, were applied to the experimental results. The kinetic analysis indicated that the pseudo-second-order rate equation promoted the development of the chemisorption phase better than the pseudo-first-order rate equation. In the case of isothermal investigations, a study of observed correlation coefficient (R²) values indicated that the Langmuir model outperformed the Freundlich model in terms of matching experimental data.

To the best of the author's information, there is no comprehensive study for copper ions removal from waste water effluent using the recently tailored and fully characterized poly (AN)-starch nanoparticle graft copolymer having 60.1 graft yield percentage as a starting substrate after chemical modification with hydroxyl amine via oximation reaction as a calorimetric sensor.

The paper aims to evaluate drying performance of earth mortar by solar drying for more durability, minimize pathologies in traditional construction and determine the influence of temperature and humidity on the microstructure of earth mortar using static gravimetric method.

A convective solar dryer was used for the pretreatment of building and solid materials for construction.

The humidity influences the mortar sorption – surface water sorption of earth mortar increased with increasing temperature.

The study used a novel method for pretreatment building materials by using solar dryer.

This study aims to model and investigate Basic Yellow 28 (BY28) adsorption onto activated carbon in batch and continuous process.

Batch adsorption experiments were carried out at 25 °C with 50 mg/L BY28 solution at pH 6 with different amounts of activated carbon. Freundlich and Langmuir adsorption isotherm models were used to model batch data. Pseudo-first-order and pseudo-second-order kinetic models were applied with linear regression. The changes of the breakthrough curve with the column height, flow rate, column diameter and adsorbent amount were examined in fixed bed column at room temperature. BY28 adsorption data were modelled by using different adsorption column models (Adams & Bohart, Thomas, Yoon & Nelson, Clark and modified dose–response) with non-linear regression.

Freundlich model and pseudo-second-order kinetic model expressed the experimental data with high compatibility. Modified dose-response model corresponded to the fixed bed column data very well.

Adsorption of Basic Yellow 28 on activated carbon in a fixed bed column was studied for the first time. Continuous adsorption process was modelled with theoretical adsorption models using non-linear regression.

This study aims to elucidate the dyeing kinetics and thermodynamic relationships of CI Reactive Red 24 (RR24) on cotton fabrics, achieve the recycling of inorganic salts and water resources and obtain comprehensive data on color parameters, fastness and other characteristics of fabrics dyed with the recycled dyeing residual wastewater.

The dyeing wastewater obtained through advanced oxidation technology was used as a medium for dyeing cotton fabrics with RR24. The absorbance value of the dyeing residue served as an evaluation index, and the relevant kinetic and thermodynamic parameters were calculated based on this absorbance. The color parameters and fastness of the fabric samples were measured to compare the performance of different dyeing media.

Dyeing cotton with RR24 in both media follows pseudo-second-order kinetics. When dyeing with wastewater media, the dye adsorption in the first 45 min increased by 0.082–1.29 g/kg compared with conventional dyeing. Furthermore, the half-dyeing time was shortened by 4.19–11.99 min and the equilibrium adsorption amount was reduced by 0.277–0.302 g/kg. The adsorption of RR24 on cotton fabrics conformed to the Freundlich model. Fabrics dyed using recycled wastewater exhibit a deeper color, with reduced red light and enhanced blue light, resulting in an overall deeper apparent color.

These dyeing kinetics and thermodynamic properties are beneficial for comprehending and interpreting the dyeing performance and behavior of reactive dyes in dyeing wastewater. They lay a theoretical foundation for the treatment and recycling of dyeing wastewater.

This study’s aim is to introduce a high-performance sorbent for the removal of both anionic (Congo red; CR) and cationic (methylene blue; MB) dyes from aqueous solutions.

Sodium silicate is adopted as a substrate for GO and AgNPs with positive charge are used as modifiers. The synthesized nanocomposite is characterized by FTIR, FESEM, EDS, BET and XRD techniques. Then, some of the most effective parameters on the removal of CR and MB dyes such as solution pH, sorbent dose, adsorption equilibrium time, primary dye concentration and salt effect are optimized using the spectrophotometry technique.

The authors successfully achieved notable maximum adsorption capacities (Qmax) of CR and MB, which were 41.15 and 37.04 mg g⁻¹, respectively. The required equilibrium times for maximum efficiency of the developed sorbent were 10 and 15 min for CR and MB dyes, respectively. Adsorption equilibrium data present a good correlation with Langmuir isotherm, with a correlation coefficient of R2 = 0.9924 for CR and R2 = 0.9904 for MB, and kinetic studies prove that the dye adsorption process follows pseudo second-order models (CR R2 = 0.9986 and MB R2 = 0.9967).

The results showed that the proposed mechanism for the function of the developed sorbent in dye adsorption was based on physical and multilayer adsorption for both dyes onto the active sites of non-homogeneous sorbent.

The as-prepared nano-adsorbent has a high ability to remove both cationic and anionic dyes; moreover, to the high efficiency of the adsorbent, it has been tried to make its synthesis steps as simple as possible using inexpensive and available materials.

Due to herbs and plants’ therapeutic properties and simplicity of availability in nature, humans have used them to treat a variety of maladies and diseases since ancient times. Later, as technology advanced, these plants and herbs gained significant relevance in some industries due to their suitable chemical composition, abundant availability and ease of access. Aegle marmelos is a species of plant that may be found in nature. Yet, little or very little literature was located on the coloration behavior of this plant’s leaves. This study aims to focus on the effect of different parameters on the extraction of colorant from Aegle marmelos leaves.

Some factors that affected on the extraction processes were examined and found to have significant impacts on the textile dyeing such as the initial dye concentration, extracted temperature, extracted bath pH and extracted time were all changed to see how they affected color extraction. The authors report a direct comparison between three heating methods, namely, microwave irradiation (MWI), ultrasonic waves (USW) and conventional heating (CH). The two kinetic models have been designed (pseudo-first and pseudo-second orders) in the context of these experiments to investigate the mechanism of the dyeing processes for fabrics under study. Also, the experimental data were analyzed according to the Langmuir and Freundlich isotherms.

From the result, it was discovered these characteristics were found to have a substantial effect on extraction efficiency. Temperature 90°C and 80°C when using CH and USW, respectively, while at 90% watt when using MWI, period 120 min when using CH as well as USW waves, while 40 min when using MWI, and pH 4, 5 and 10 for polyamide, wool and cotton, respectively, were the optimal extraction conditions. Also, the authors can say that wool gives a higher absorption than the other fabric. Additionally, MWI provided the best color strength (K/S) value, and homogeneity, at low temperatures reducing the energy and time consumed. The coloring follows the order: MWI > USW > CH. The adsorption isotherm of wool could be well fitted by Freundlich isotherm when applying CH and USW as a heating source, while it is well fitted by the Langmuir equation in the case of MWI. In the study, it was observed that the pseudo-first-order kinetic model fits better the experimental results of CH with a constant rate K₁ = −0.000171417 mg/g.min, while the pseudo-second-order kinetic model fits better the experimental results of absorption of both MWI (K2 = 38.14022572 mg/g.min) and USW (K₂ = 12.45343554 mg/g.min).

There is no research limitation for this work. Dye was extracted from Aegle marmelos leaves by applying three different heating sources (MWI, ultrasonic waves [USWW] and CH).

This work has practical applications for the textile industry. It is concluded that using Aegle marmelose leaves can be a possible alternative to extract dye from natural resource by applying new technology to save energy and time and can make the process greener.

Socially, it has a good impact on the ecosystem and global community because the extracted dye does not contain any carcinogenic materials.

The work is original and contains value-added products for the textile industry and other confederate fields.

This study aims to prepare an imprinted composite membrane with grafted temperature-sensitive blocks for the efficient adsorption and separation of rhenium(Re) from aqueous solutions.

PVDF resin membrane was used as the substrate, dopamine and chitosan (CS) were used to modify the membrane surface and temperature-sensitive block PDEA was grafted on the membrane surface. Then acrylic acid (AA) and N-methylol acrylamide (N-MAM) were used as the functional monomers, ethyleneglycol dimethacrylate (EGDMA) as the cross-linker and ascorbic acid-hydrogen peroxide (Vc-H₂O₂) as the initiator to obtain the temperature-sensitive ReO4⁻ imprinted composite membranes.

The effect of the preparation process on the performance of CS–Re–TIICM was investigated in detail, and the optimal preparation conditions were as follows: the molar ratios of AA–NH₄ReO₄, N-MAM and EGDMA were 0.13, 0.60 and 1.00, respectively. The optimal temperature and time of the reaction were 40 °C and 24 h. The maximum adsorption capacity of CS–Re–TIICM prepared under optimal conditions was 0.1071 mmol/g, and the separation was 3.90 when MnO4⁻ was used as the interfering ion. The quasi first-order kinetics model and Langmuir model were more suitable to describe the adsorption process.

With the increasing demand for Re, the recovery of Re from Re-containing secondary resources becomes important. This study demonstrated a new material that could be separated and recovered Re in a complex environment, which could effectively alleviate the conflict between the supply and demand of Re.

This contribution provided a new material for the selective separation and purification of ReO4⁻, and the adsorption capacity and separation of CS–Re–TIICM were increased with 1.673 times and 1.219 time compared with other Re adsorbents, respectively. In addition, when it was used for the purification of NH₄ReO₄ crude, the purity was increased from 91.950% to 99.999%.

This study aims to investigate the efficacy of Ag@GO/Na₂SiO₃ nanocomposite in eliminating As from aqueous solutions. Employing response surface methodology, the research systematically examines the adsorption process.

Various experimental parameters including sample pH, contact time, As concentration and adsorbent dosage are optimized to enhance the As removal process.

Under optimized conditions, the initial As concentration, contact time, pH and adsorbent dosage are determined to be 32 ppm, 50 mins, 6.5 and 0.4 grams, respectively. While the projected removal of As stands at 97.6% under these conditions, practical application achieves a 93% removal rate. Pareto analysis identifies the order of significance among factors as follows: adsorbent dosage > contact time > pH > As concentration.

This study highlights the potential Ag@GO/Na₂SiO₃ as a promising adsorbent for efficiently removing industrial As from aqueous solutions, and it is likely to have a good sufficiency in the filtration of water and wastewater treatment plans to remove some chemical pollution, including paints and heavy metals.

The simplicity of the nanocomposite preparation method without the need for advanced equipment and the cheapness of the raw materials and its potential ability to remove As are the prominent advantages of this research.

Corrosion is a major concern for many industries that use metals as structural or functional materials, and the use of corrosion inhibitors is a widely accepted strategy to protect metals from deterioration in corrosive environments. Moreover, the toxic nature, non-biodegradability and price of most conventional corrosion inhibitors have encouraged the application of greener and more sustainable options, with natural and synthetic drugs being major actors. Hence, this paper aims to stress the capability of natural and synthetic drugs as manageable and sustainable, environmentally friendly solutions to the problem of metal corrosion.

In this review, the recent developments in the use of natural and synthetic drugs as corrosion inhibitors are explored in detail to highlight the key advancements and drawbacks towards the advantageous utilization of drugs as corrosion inhibitors.

Corrosion is a critical issue in numerous modern applications, and conventional strategies of corrosion inhibition include the use of toxic and environmentally harmful chemicals. As greener alternatives, natural compounds like plant extracts, essential oils and biopolymers, as well as synthetic drugs, are highlighted in this review. In addition, the advantages and disadvantages of these compounds, as well as their effectiveness in preventing corrosion, are discussed in the review.

This survey stresses on the most recent abilities of natural and synthetic drugs as viable and sustainable, environmentally friendly solutions to the problem of metal corrosion, thus expanding the general knowledge of green corrosion inhibitors.