Search results

This paper aims to investigate the impact of combining grain-oriented electrical steel (GOES) grades on specific iron losses and the flux density distribution within a single-phase magnetic core.

This paper presents the results of finite-element method (FEM) simulations investigating the impact of mixing two different GOES grades on losses of a single-phase magnetic core. The authors used different models: a 3D model with a highly detailed geometry including both saturation and anisotropy, as well as a simplified 2D model to save computation time. The behavior of the flux distribution in the mixed magnetic core is analyzed. Finally, the results from the numerical simulations are compared with experimental results.

The specific iron losses of a mixed magnetic core exhibit a nonlinear decrease with respect to the GOES grade with the lowest losses. Analyzing the magnetic core behavior using 2D and 3D FEM shows that the rolling direction of the GOES grades plays a critical role on the nonlinearity variation of the specific losses.

The novelty of this research lies in achieving an optimum trade-off between the manufacturing cost and the core efficiency by combining conventional and high-performance GOES grade in a single-phase magnetic core.

This paper aims at developing an improved method, based on binary search algorithm (BSA) for the steady-state analysis of self-excited induction generators (SEIGs), which are increasingly used in wind energy electric conversion systems. The BSA is also compared with linear search algorithm (LSA) to bring out the merits of BSA over LSA.

All the parameters of SEIG, including the varying core loss of the machine, have been considered to ensure accuracy in the predetermined performance values of the set up. The nodal admittance method has been adopted to simplify the equivalent circuit of the generator and load. The logic and steps involved in the formulation of the complete procedure have been illustrated using elaborate flowcharts.

The proposed approach is validated by the experimental results, obtained on a three-phase 240 V, 5.0 A, 2.0 kW SEIG, which closely match with the corresponding predicted performance values. The analysis is shown to be easy to implement with reduced computation time.

A novel improved and simplified technique has been formulated for estimating the per unit frequency (a), magnetizing reactance (X_m) and core loss resistance (R_m) of the SEIG using the nodal admittance of its equivalent circuit. The accuracy of the predetermined performance is enhanced by considering the SEIG’s varying core loss. Only simple MATLAB programming has been used for adopting the algorithms.

Evaluating the multiphysics performance of an electric motor can be a computationally intensive process, especially where several complex subsystems of the motor are coupled together. For example, evaluating acoustic noise requires the coupling of the electromagnetic, structural and acoustic models of the electric motor. Where skewed poles are considered in the design, the problem becomes a purely three-dimensional (3D) multiphysics problem, which could increase the computational burden astronomically. This study, therefore, aims to introduce surrogate models in the design process to reduce the computational cost associated with solving such 3D-coupled multiphysics problems.

The procedure involves using the finite element (FE) method to generate a database of several skewed rotor pole surface-mounted permanent magnet synchronous motors and their corresponding electromagnetic, structural and acoustic performances. Then, a surrogate model is fitted to the data to generate mapping functions that could be used in place of the time-consuming FE simulations.

It was established that the surrogate models showed promising results in predicting the multiphysics performance of skewed pole surface-mounted permanent magnet motors. As such, such models could be used to handle the skewing aspects, which has always been a major design challenge due to the scarcity of simulation tools with stepwise skewing capability.

The main contribution involves the use of surrogate models to replace FE simulations during the design cycle of skewed pole surface-mounted permanent magnet motors without compromising the integrity of the electromagnetic, structural, and acoustic results of the motor.

The purpose of this study is to provide the enhancement of power quality of a high power-rated voltage source inverter driven induction motor with a three-phase, three-level neutral point clamped converter placed at the front end, while a passive power filter is connected in shunt with it. The improvement in power quality can be achieved by reducing the total harmonic distortion in source current. The controllers were designed for the linearization of the high-power induction motor drive. A control method is presented for the regulation of the common DC-link voltage.

The induction motor is modeled using its dynamic equations, and a decoupling controller is designed to linearize the nonlinear dynamics of the drive through feedback. The common DC-link voltage of the proposed front-end connected converter is monitored and controlled through a control method which feeds the pulse width modulated inverter that drives the induction motor. A passive power filter is designed to meet the reactive power requirement of the system in addition to improve the power quality.

Simulations were carried out for the proposed topology of the drive mechanism, and the outcomes were analyzed by a comparative analysis of the drive system both in the presence of the passive filter as well as in the absence of the filter. The total harmonic distortion is found to be reduced enough to meet the standards with the designed filter, and the reactive power is also compensated considerably. The input power factor at the supply side is maintained almost to unity, and the DC-link voltage of the proposed circuit topology is maintained at the desired level. The overall performance of the drive system was found to be useful and economical.

A new topology of a front-end connected three-level neutral point clamped converter to a high power-rated induction motor drive is proposed. The drive is fed by a pulse width modulated inverter with a common DC-link with the front end connected converter. A passive filter is designed with respect to the reactive power requirement of the system and connected in shunt to the converter at the supply side. Control schemes are designed and used for the drive system and also for the regulation of the common DC-link voltage of the proposed front end connected converter.

This paper aims to identify the interplay of standard Capesize optimal speeds for time charter equivalent (TCE) maximization in the Australia–China iron ore route and the optimal speeds as an operational tool for compliance with the International Maritime Organization (IMO) carbon intensity indicator (CII).

The TCE at different speeds have been calculated for four standard Capesize specifications: (1) standard Capesize with ecoelectronic engine; (2) standard Capesize with non-eco engine (3) standard Capesize vessel with an eco-electronic engine fitted with scrubber and (4) standard Capesize with non-eco engine and no scrubber fitted.

Calculations imply that in a highly inflationary bunker price context, the dollar per ton freight rates equilibrates at levels that may push optimal speeds below the speeds required for minimum CII compliance (C Rating) in the Australia–China trade. The highest deviation of optimal speeds from those required for minimum CII compliance is observed for non-eco standard Capesize vessels without scrubbers. Increased non-eco Capesize deployment would see optimal speeds structurally lower at levels that could offer CII ratings improvements.

While most of the studies have covered the use of speed as a tool to improve efficiency and emissions in the maritime sector, few have been identified in the literature to have examined the interplay between the commercial and operational performance in the dry bulk sector stemming from the freight market equilibrium. The originality of this paper lies in examining the above relation and the resulting optimal speed selection in the Capesize sector against mandatory environmental targets.

The final properties of ductile iron are decided by the inoculant processing while pouring the melt. The shape and size of nodules generated during solidification are of paramount importance in solidification of ductile cast iron. The purpose of this study is to examine the effect of different inoculant addition on the solidification of ductile cast iron melt through thermal analysis.

Thermal analysis has recently grown as a tool for modeling the solidification behavior of ductile cast irons. Iron properties will be predicted by analyzing the cooling curve patterns of the melts and predicting the related effectiveness of inoculant processing. In this study, thermal analysis is used to evaluate the need for inoculation.

The amount and type of inoculation will affect the amount of undercooling during the solidification of ductile cast iron. It is found that the addition of 0.1 to 0.4 Wt.% inoculant lowers the austenite dendrite formation starting temperature while increasing the eutectic freezing temperature. Microstructure analysis revealed that the addition of inoculation increases the nodule count from 103 to 242 nodules. The beneficial effects of inoculation are sustained by an improved graphitization factor, which shows the formation of graphite nodules in the second phase of the eutectic reaction.

The inoculation treatment has improved metallurgical occurrences such as carbide to graphite conversion, graphite microstructure control, graphite nodule count at the start of solidification and the last stage of solidification, which determines the soundness of casting. The foundry industry can follow these steps for monitoring the solidification of ductile iron castings.

This study aims to determine the effect of replacing a portion of the cement in the concrete mixture with silica fume (SF) on the corrosion resistance of reinforcing bars, the compressive strength of concrete and the tensile strength of hook bars in both corroded and non-corroded external joints of structures. The external beam-column connection was studied because of its critical role in maintaining structural continuity in all three directions and providing resistance to rotation.

In external concrete joints, the bars at the end of the beams are often bent at 90° to form hooks that embed in columns. Owing to the importance of embedding distance and the need to understand its susceptibility to corrosion damage from chloride attack, a series of experiments were conducted on 12 specimens that accurately simulate real-site conditions in terms of dimensions, reinforcement and hook bars. SF was replaced with 10% and 15% of the weight of cement in the concrete mixture. To simulate corrosion, the specimens were subjected to accelerated corrosion in the laboratory by applying a low continuous current of 0.35 mA for 58 days.

The results revealed the effect of SF in improving the compressive strength of concrete, the pullout resistance of the hook bars and the corrosion resistance. In addition, it showed an apparent effect of the corrosion of reinforcing bars in reducing the bonding strength of hook bars with concrete and the effect of SF in improving this strength.

It was noted that the improvement of the results, achieved by replacing 10% of the weight of cement with SF, was significantly close to the results obtained by replacing 15% of the SF. It is recommended that an SF ratio of 10% be adopted to achieve the greatest economic savings.

This study seeks to collaborate with the discussions on the usefulness of the narrative approach in accounting. In this context, this study aims to elaborate small collective stories, developed from interviews, to expose the population’s perception of the social and environmental impact (positive and negative externalities) resulting from iron ore mining in the city of Congonhas-Minas Gerais (MG).

This research, using counternarratives, aims to elaborate small collective stories, developed from 52 interviews, to expose the population’s perception of externalities resulting from the exploitation of iron ore in the city of Congonhas-MG, Brazil, to give more insight for social and environmental accounting reporting. A qualitative investigation is used with a narrative approach that focuses on a specific event in the participants’ lives.

The authors sought to create a sense of collective experiences of the interviewees through narratives representative of the residents’ perception of externalities in the form of small collective stories. However, it can be observed that the local population recognizes the impact of numerous externalities. Likewise, the use of narratives allows the reader to experience another reality – a reflection on the impact of business activities in a given context. Unlike conventional corporate social reporting, models based on qualitative information can be inclusive, produced by/for the community toward action that transforms the local reality.

This study intends to contribute to the debate on reporting models that are developed by and for external stakeholders. This approach has the potential to improve participants’ both awareness and engagement, supporting transformative social action. This study makes several contributions. It contributes to the literature with a narrative approach, which is not often used in the accounting literature; it brings insights from the Latin American context, which is especially valuable given how the Anglo-American accounting literature includes few papers addressing this context; it presents the view of marginalized communities that are too often overlooked (this narrative approach offers important insights into the lived experience of people at a very granular level).

This study examines the evidence of the impact of climate change on the financial performance of basic materials companies in Vietnam.

The research sample includes eighty-two basic materials companies listed on the Vietnamese stock market from 2003 to 2022. This study used one-way and two-way fixed-effects feasible generalized least squares (FGLS) estimation methods.

Climate change, measured through variables including changes in temperature, average rainfall, greenhouse gas emissions and rising sea levels, has a negative impact on the financial performance of companies in this industry. The study also found that, with rising temperatures, the financial performance of steel manufacturing companies decreased less than that of coal mining and forestry companies, but increasing greenhouse gases and rising sea levels reduced the financial performance of steel companies. We did not find evidence of any difference in the impact of climate change on the financial performance of basic materials companies before and after the UN Climate Change Conference (COP 21). This is a new finding, which is consistent with empirical studies in Vietnam and different from previous studies in that it provides new evidence on the impact of climate change on the financial performance of basic materials companies in the Vietnamese market and cross-checks the impact of climate change by sector and over time.

To the best of our knowledge, this is one of the first articles on climate change and the financial performance of basic materials companies.

This study aims to prevent occupational accidents occurring in the manufacturing industry by means of touch sensors. When the occupational accidents occurring in the manufacturing industry around the world are examined, it is seen that approximately 88% of occupational accidents occur from “dangerous movement” and 10% from “dangerous situation.” Although some studies related to safety culture studies, safety studies in design and collective or personal protective measures have been started, they have not been brought to an adequate level. It is observed that studies on dangerous movements continue even in many developed countries. In this study, first of all, a literature study was conducted. Occupational accidents experienced in the manufacturing sector in Turkey have been examined. In line with these investigations, a prototype circuit protection system has been developed that can prevent accidents caused by dangerous movement. With the circuit, its applicability and effectiveness were measured by conducting experiments on different manufacturing machines. The prototype circuit applied in this paper was made based on the logic of protective measures made on sawstop machines used in different sectors. In the experimental study conducted, it was observed that in 30 experiments conducted with a prototype on ten separate manufacturing machines, it stopped the machines 26 times at minimum and 29 times at maximum. On average, when looking at the system efficiency values, it was seen that the system was 81.6% effective, and it was observed that positive results could be obtained when converted into a real product.

In this study, their contribution to the prevention of work accidents caused by presses and rotary accents from machines used in the manufacturing industry by means of touch sensors used in Industry 4.0 was examined.

With Industry 4.0, different automation systems began to be switched in many areas and sectors. Studies have started on different sensors used also in Industry 4.0 in occupational health and safety studies, but it is seen that they have not been applied at an adequate level. It should be designed in such a way as to prevent errors or stop these errors in the studies performed. Today, sensors are produced at much lower costs than before. In addition, the constantly developing technology provides great convenience for these applications.

This study was applied for press and cylinder machines from manufacturing machines. This study has been tried for machines producing a maximum pressure of 300 tons.

A prototype was designed. Trials were done on some machines by prototype. There could be improve and find different solutions for safety problems in the industry with this perspective.