Search results

It is well known that the prefabricated vertical drain (PVD) installation process generates a significant soil disturbance around PVD. This disturbed zone significantly affects the rate of settlement and excess pore pressure dissipation. However, the characteristics of these zones were still uncertain and difficult to quantify; there remains large discrepancy among researchers. This study aims to develop a simple analytical solution for radial consolidation analysis of PVD-installed deposit considering mandrel-induced disturbance.

The proposed solution takes into account the nonlinear distributions of both horizontal hydraulic conductivity and compressibility toward the drain. The proposed solution was applied to analyze field behavior of test embankment in New South Wales, Australia.

Both effects significantly increased the time required to achieve a certain degree of consolidation. The effect of hydraulic conductivity on the consolidation rate was more significant than the effect of compressibility variation. And, the increased compressibility in the soil-disturbed zone due to mandrel installation significantly increased vertical strain of the PVD-improved soil deposit. The predicted results using the proposed analytical solution were in good agreement with the field measurements.

A geotechnical engineer could use the proposed analytical solution to predict consolidation behavior of drainage-installed ground.

Consolidation behavior of PVD-installed ground could be reasonably predicted by using the proposed solution with considering variations of both hydraulic conductivity and compressibility due to PVD installation.

The purpose of this study is to understand the basics of interactions of groundwater and surface water, which is needed for effective management of water resources.

The experimental setup was framed using curved flume and the straight flume, which simulates the model of river and groundwater storage, respectively. The model set up further consists, downstream, central and upstream sections where 14 observation wells, which are arranged at a measured distance from the canal side.

Exit gradient is higher at downstream when the average head differences between canal and river are 31.9 cm and 35.7 cm. Free seepage height is more in the downstream wells than upstream and central wells. At the downstream section, there is a greater chance of instability of the riverbank.

Results will be used for better planning of hydraulic structural design.

Results will help in storing the large water and better irrigation planning for the water acute states and locations.

The originality is own developed physical model and its own first type to understand the basic of interaction and effects.

The consolidation behavior of prefabricated vertical drain (PVD)-installed soft deposits mainly depends on the PVD performance. The purpose of this study is to propose a numerical solution for the consolidation of PVD-installed soft soil using the large-strain theory, in which the reduction of discharge capacity of PVD according to depth and time is simultaneously considered.

The proposed solution also takes into account the general constitute relationship of soft soil. Subsequently, the proposed solution is applied to analyze and compare with the monitoring data of two cases, one is the experimental test and another is the test embankment in Saga airport.

The results show that the reduction of PVD discharge capacity according to depth and time increased the duration required to achieve a certain degree of consolidation. The consolidation rate is more sensitive to the reduction of PVD discharge capacity according to time than that according to the depth. The effects of the reduction of PVD discharge capacity according to depth are more evident when PVD discharge capacity decreases. The predicted results using the proposed numerical solution were validated well with the monitoring data for both cases in verification.

In this study, the variation of PVD discharge capacity is only considered in one-dimensional consolidation. However, it is challenging to implement a general expression for discharge capacity variation according to time in the two-dimensional numerical solution (two-dimensional plane strain model). This is the motivation for further study.

A geotechnical engineer could use the proposed numerical solution to predict the consolidation behavior of the drainage-improved soft deposit considering the PVD discharge capacity variation.

The large-strain consolidation of PVD-installed soft deposits could be predicted well by using the proposed numerical solution considering the PVD discharge capacity variations according to depth and time.

In petroleum industry, hydraulic fracturing is essential to enhance oil productivity. The hydraulic fractures are usually generated in the process of hydraulic fracturing. Although some mathematical models were proposed to analyze the well-flow behavior of conventional fracture, there are few models to depict unconventional fracture like reorientation fracture. To figure out the effect of reorientation fracture on production enhancement and guide the further on-site operating, this paper aims to investigate the well-flow behavior of vertical reorientation fracture in horizontal permeability anisotropic reservoir.

Based on the governing equation considering horizontal permeability anisotropy, the mathematical models for reorientation fractures in infinite reservoir are developed by using the principle of superposition. Furthermore, a rectangular closed drainage area is also considered to investigate the well-flow behavior of reorientation fracture, and the mathematical models are developed by using Green’s and source functions.

Computational results indicate that the flux distribution of infinite conductivity fracture is uniform at very early times. After a period, it will stabilize eventually. High permeability anisotropy and small inclination angle of reorientation will cause significant end point effect in the infinite conductivity fracture. The reorientation fractures with small inclination angle in high anisotropic reservoir are capable of improving 1-1.5 times more oil productivity in total.

This paper develops the mathematical methods to study the well-flow behavior for unconventional fracture, especially for reorientation fracture. The results validate the production enhancement effect of reorientation fracture and identify the sensitive parameters of productivity.

The purpose of this paper is to develop and validate a numerical model to study the effect of changing hydraulic parameters on saltwater intrusion in coastal aquifers.

The numerical model SEAWAT is validated and applied to a hypothetical case (Henry problem) and a real case study (Biscayne aquifer, Florida, USA) for different values of hydraulic parameters including; hydraulic conductivity, porosity, dispersion, diffusion, fluid density and solute concentration. The dimensional analysis technique is used to correlate these parameters with the intrusion length.

The results show that the hydraulic parameters have a clear effect on saltwater intrusion as they increase the intrusion in some cases and decrease it in some other cases. The results indicate that changing hydraulic parameters may be used as a control method to protect coastal aquifers from saltwater intrusion.

The results of the application of the model to the Biscayne aquifer in Florida showed that the intrusion can be reduced to 50 percent when the hydraulic conductivity is reduced to 50 percent. Decreasing hydraulic conductivity by injecting some relatively cheap materials such as bentonite can help to reduce the intrusion of saltwater. So the saltwater intrusion can be reduced with relatively low cost through changing some hydraulic parameters.

A relationship to calculate intrusion length in coastal aquifer is developed and the impact of different hydraulic parameters on saltwater intrusion is highlighted. Control of saltwater intrusion using relatively cheap method is presented.

Traditional laboratory measurements of soil water diffusivity (D) and soil water retention curve (SWRC) are always time-consuming and labor-intensive. Therefore, this paper aims to present a simple and robust test method for determining D and SWRC without reducing accuracy.

In this study, a D model of unsaturated soil was established based on Gardner–Russo model and then a combination of Gardner–Russo model with one-dimensional horizontal absorption method to obtain n and a parameters of Gardner–Russo model. One-dimensional horizontal absorption experiments on loam, silt loam and sandy clay loam were conducted to obtain the relationships between measured infiltration rate and cumulative infiltration with wetting front distance. Based on the obtained relationships, the measured infiltration data from the one-dimensional horizontal absorption tests were used to calculate n and a parameters and further constructing D and SWRC.

Both the calculated D and SWRC inversed from the infiltration data were in good agreement with the measured ones that obtained from the traditional horizontal absorption method and the centrifuge method, respectively. Error analysis indicated that only the infiltration data are enough to reliably synchronously determine D and SWRC.

A simple and robust method is proposed for synchronous determination of soil water diffusivity and water retention curve.

Apart from the basic material properties of liquid lubricants, such as, e.g., the viscosity and density of the hydraulic fluid, it is also important to have information regarding the electrical properties of the fluid used. The latter is closely related to the purpose, type, structure, and conditions of use of a hydraulic system, especially the powertrain design and fluid condition monitoring. The insulating capacity of the hydraulic fluid is important in cases where the electric motor of the pump is immersed in the fluid. In other cases, on the basis of changing the electrical conductive properties of the hydraulic fluid, we can refer its condition, and, on this basis, the degree of degradation.

The paper first highlights the importance of knowing the electrical properties of hydraulic fluids and then aims to compare these properties, such as the breakdown voltage of commonly used hydraulic mineral oils and newer ionic fluids suitable for use as hydraulic fluids.

Knowledge of this property is crucial for the design approach of modern hydraulic compact power packs. In the following, the emphasis is on the more advanced use of known electrical quantities, such as electrical conductivity and the dielectric constant of a liquid.

Based on the changes in these quantities, we have the possibility of real-time monitoring the hydraulic fluid condition, on the basis of which we judge the degree of fluid degradation and its suitability for further use.

Multi-well hydrofracturing is an important technology to create new fractures and expand existing fractures to increase reservoir permeability. The propagation morphology of the fracture network is affected by the disturbance between the fractures initiation sequences and spacings between adjacent wells. However, it remains unclear how well spacing and initiation sequences lead to fracture propagation, deflection and connection.

In this study, the thermal-hydro-mechanical coupling effect in the hydrofracturing process was considered, to establish a finite element-discrete element model of multistage hydrofracturing in a horizontal well. Using typical cases, the unstable propagation of hydraulic fractures in multiple horizontal wells was investigated under varying well spacing and initiation sequences. Combined with the shear stress shadow caused by in situ stress disturbed by fracture tip propagation, the quantitative indexes of fracture propagation such as length, volume, displacement vector, deflection and unstable propagation behavior of the hydrofracturing fracture network were analyzed.

The results show that the shear stress disturbance caused by multiple hydraulic fractures is a significant factor in multi-well hydrofracturing. Reducing the spacing between multiple wells increases the stress shadow area and aggravates the mutual disturbance and deflection between the fractures. The quantitative analysis results show that a decrease of well spacing reduces the total length of hydraulic fractures but increases the total volume of the fracture; compared with sequential and simultaneous fracturing, alternate fracturing can effectively reduce stress shadow area, alleviate fracture disturbance and generate larger fracture propagation length and volume.

The numerical models and results of the unstable propagation and stress evolution of the hydraulic fracture network under thermal-hydro-mechanical coupling obtained in this study can provide useful guidance for the evaluation and design of rock mass fracture networks in deep unconventional oil and gas reservoirs.

It is well-known that consolidation rate of prefabricated vertical drain (PVD)-installed ground is closely related to the discharge capacity of PVD, which decreases with an increase in effective stress. This paper aims to present consolidation behaviors of PVD-improved ground considering a varied discharge capacity of PVD.

A simple equivalent vertical hydraulic conductivity (k′_ve method) was proposed in plane strain numerical analysis, in which the effect of decreased discharge capacity with depth was considered. Numerical analysis was applied to analyze field behaviors of test embankment of soft mucky deposit.

Finite element method results indicated that consolidation behaviors of PVD-improved soil with a nonlinear distribution of discharge capacity with depth were in a good agreement with the observed field behaviors, compared with those with a constant discharge capacity and a linear distribution of discharge capacity. At a given time and depth, the consolidation rate in the case of discharge capacity with a nonlinear distribution is lower than that of a linear or constant distribution.

A geotechnical engineer could use the proposed method to predict consolidation behaviors of drainage-installed ground.

Consolidation behaviors of PVD-installed ground could be reasonably predicted by using the proposed method with considering effect of discharge capacity reduction.

Inclination angle has been reported to have an enhancing effect on the thermal-hydraulic characteristics and entropy of some thermal systems. Therefore, this paper aims to numerically investigate the effects of inclination angle, volume concentration and Reynolds number on the thermal and hydraulic characteristics and entropy generation rates of water-based Al₂O₃ nanofluids through a smooth circular aluminum pipe in a turbulent flow.

A constant heat flux of 2,000 Watts is applied to the circular surface of the tube. Reynolds number is varied between 4,000 and 20,000 for different volume concentrations of alumina nanoparticles of 0.5%, 1.0% and 2.0% for tube inclination angles of ±90o, ±60o, ±45o, ±30o and 0o, respectively. The simulation is performed in an ANSYS Fluent environment using the realizable kinetic energy–epsilon turbulent model.

Results show that +45o tube orientation possesses the largest thermal deviations of 0.006% for 0.5% and 1.0% vol. concentrations for Reynolds numbers 4,000 and 12,000. −45o gives a maximum pressure deviation of −0.06% for the same condition. The heat transfer coefficient and pressure drop give maximum deviations of −0.35% and −0.39%, respectively, for 2.0% vol. concentration for Reynolds number of 20,000 and angle ±90o. A 95%–99.8% and 95%–98% increase in the heat transfer and total entropy generation rates, respectively, is observed for 2.0% volume concentration as tube orientation changes from the horizontal position upward or downward.

Research investigating the effect of inclination angle on thermal-hydraulic performance and entropy generation rates in-tube turbulent flow of nanofluid is very scarce in the literature.