Search results

The purpose of this paper is to present a semi-analytical solution to one-dimensional (1D) consolidation induced by a constant inner point sink in viscoelastic saturated soils.

Based on the Kelvin–Voigt constitutive law and 1D consolidation equation of saturated soils subject to an inner sink, the analytical solutions of the effective stress, the pore pressure and the surface settlement in Laplace domain were derived by using Laplace transform. Then, the semi-analytical solutions of the pore pressure and the surface settlement in physical domain were obtained by implementing Laplace numerical inversion via Crump method.

As for the case of linear elasticity, it is shown that the simplified form of the presented solution in this study is the same as the available analytical solution in the literature. This to some degree depicts that the proposed solution in this paper is reliable. Finally, parameter studies were conducted to investigate the effects of the relevant parameters on the consolidation settlement of saturated soils. The presented solution and method are of great benefit to provide deep insights into the 1D consolidation behavior of viscoelastic saturated soils.

The presented solution and method are of great benefit to provide deep insights into the 1D consolidation behavior of viscoelastic saturated soils. Consolidation behavior of viscoelastic saturated soils could be reasonably predicted by using the proposed solution with considering variations of both flux and depth because of inner point sink.

To establish relationships between effective vertical stress‐void ratio and hydraulic conductivity‐void ratio on high water content dredged clays, which are then used to predict the field consolidation behavior.

The large strain consolidation model is used for numerical modeling of large‐strain self‐weight consolidation. Material parameters determined from seepage‐induced consolidation tests provided satisfactory predictions of field compression behavior.

It is shown that realistic estimates of self‐weight consolidation behavior of dredged sea bottom sediments stored on land can be made by using a seepage‐induced consolidation test system and an appropriate consolidation model such as CS2, which is very important in storage capacity design and reclamation planning of such storage areas.

In this paper, the findings are presented of an experimental investigation of the consolidation behavior of Golden Horn dredge material using a seepage‐induced testing system. The experimentally determined consolidation properties have yielded useful relationships for the variation of void ratio with effective stress and coefficient of permeability with void ratio, and use of these has enabled a realistic prediction of the observed behavior.

It is well-known that consolidation rate of prefabricated vertical drain (PVD)-installed ground is closely related to the discharge capacity of PVD, which decreases with an increase in effective stress. This paper aims to present consolidation behaviors of PVD-improved ground considering a varied discharge capacity of PVD.

A simple equivalent vertical hydraulic conductivity (k′_ve method) was proposed in plane strain numerical analysis, in which the effect of decreased discharge capacity with depth was considered. Numerical analysis was applied to analyze field behaviors of test embankment of soft mucky deposit.

Finite element method results indicated that consolidation behaviors of PVD-improved soil with a nonlinear distribution of discharge capacity with depth were in a good agreement with the observed field behaviors, compared with those with a constant discharge capacity and a linear distribution of discharge capacity. At a given time and depth, the consolidation rate in the case of discharge capacity with a nonlinear distribution is lower than that of a linear or constant distribution.

A geotechnical engineer could use the proposed method to predict consolidation behaviors of drainage-installed ground.

Consolidation behaviors of PVD-installed ground could be reasonably predicted by using the proposed method with considering effect of discharge capacity reduction.

It is well known that the prefabricated vertical drain (PVD) installation process generates a significant soil disturbance around PVD. This disturbed zone significantly affects the rate of settlement and excess pore pressure dissipation. However, the characteristics of these zones were still uncertain and difficult to quantify; there remains large discrepancy among researchers. This study aims to develop a simple analytical solution for radial consolidation analysis of PVD-installed deposit considering mandrel-induced disturbance.

The proposed solution takes into account the nonlinear distributions of both horizontal hydraulic conductivity and compressibility toward the drain. The proposed solution was applied to analyze field behavior of test embankment in New South Wales, Australia.

Both effects significantly increased the time required to achieve a certain degree of consolidation. The effect of hydraulic conductivity on the consolidation rate was more significant than the effect of compressibility variation. And, the increased compressibility in the soil-disturbed zone due to mandrel installation significantly increased vertical strain of the PVD-improved soil deposit. The predicted results using the proposed analytical solution were in good agreement with the field measurements.

A geotechnical engineer could use the proposed analytical solution to predict consolidation behavior of drainage-installed ground.

Consolidation behavior of PVD-installed ground could be reasonably predicted by using the proposed solution with considering variations of both hydraulic conductivity and compressibility due to PVD installation.

The consolidation behavior of prefabricated vertical drain (PVD)-installed soft deposits mainly depends on the PVD performance. The purpose of this study is to propose a numerical solution for the consolidation of PVD-installed soft soil using the large-strain theory, in which the reduction of discharge capacity of PVD according to depth and time is simultaneously considered.

The proposed solution also takes into account the general constitute relationship of soft soil. Subsequently, the proposed solution is applied to analyze and compare with the monitoring data of two cases, one is the experimental test and another is the test embankment in Saga airport.

The results show that the reduction of PVD discharge capacity according to depth and time increased the duration required to achieve a certain degree of consolidation. The consolidation rate is more sensitive to the reduction of PVD discharge capacity according to time than that according to the depth. The effects of the reduction of PVD discharge capacity according to depth are more evident when PVD discharge capacity decreases. The predicted results using the proposed numerical solution were validated well with the monitoring data for both cases in verification.

In this study, the variation of PVD discharge capacity is only considered in one-dimensional consolidation. However, it is challenging to implement a general expression for discharge capacity variation according to time in the two-dimensional numerical solution (two-dimensional plane strain model). This is the motivation for further study.

A geotechnical engineer could use the proposed numerical solution to predict the consolidation behavior of the drainage-improved soft deposit considering the PVD discharge capacity variation.

The large-strain consolidation of PVD-installed soft deposits could be predicted well by using the proposed numerical solution considering the PVD discharge capacity variations according to depth and time.

The purpose of this paper is to evaluate the influence of a mixture of nutrient solution, bacteria and biofilm on the consolidation, unconfined compression and desiccation characteristics of two soils that could be used in waste containment applications.

Experimental work was conducted to investigate the influence of biofilm on the desiccation, strength and consolidation characteristics of two barrier soils. The soils were evaluated with water alone and with a biofilm solution composed of nutrients, bacteria and exopolymeric substances (EPS). These solutions were mixed with a locally available clay (“red bull tallow” (RBT)) as well as a mix of 65 percent sand and 35 percent bentonite (65‐35 Mix).

Reductions in strength and increases in ductility are observed with biofilm amendment for two soil types. The shear strength was reduced from 413 to 313 kPa and from 198 to 179 kPa for RBT and 65‐35 Mix, respectively. Desiccation tests reveal an increase in moisture retention for early time increments in amended specimens, while both increases and decreases are noted after extended drying. Increases in the rate of consolidation and modest decreases in the compression and swell index were observed. In particular, the consolidation coefficient was increased from 0.036 to 0.064 cm²/min and from 0.060 to 0.093 cm²/min for RBT and 65‐35 Mix, respectively.

These results are useful in establishing the broader impacts of using biofilm as an additive to increase the performance (e.g. reduce hydraulic conductivity and increase resistance to crack formation) of barrier materials in waste containment applications. Moreover, the data provide insight into the geotechnical implications of biofilm‐producing methanotrophic activity that occurs naturally in the covers of municipal solid waste landfills.

Very little research has been published on the influence of biofilm on the behavior of barrier materials in general, and on geotechnical properties in particular. This paper is unique in making the connection between methanotrophic activity, soil modification and barrier material performance.

This paper aims to investigate the behaviour of geosynthetic reinforced deep cement mixed (DCM) column-supported embankments constructed over soft soils.

Coupled consolidation analyses based on the finite element method are carried out assuming that the soil and DCM columns are fully saturated porous mediums. In the first part of the paper, a case study of an embankment constructed over a very soft soil deposit in Finland is presented. Two- and three-dimensional finite element models for the case study are developed including isolated and attached DCM columns beneath the embankment to capture the arching mechanism between DCM columns. The model simulations were carried out considering the actual staged construction procedure adopted in the field. Finite element predictions show good agreement with field data and confirm that the load transfer is mainly between attached columns beneath the embankment. Next, the significance of geosynthetic reinforcement on the load transfer mechanism is investigated. Finally, the influence of permeability of columns and soft soil on the performance of geosynthetic reinforcement column-supported embankments is studied.

Results demonstrate that the excess pore pressure dissipation rate is fast in DCM column-improved ground compared to the same case without any columns, although the same permeability is assigned to both DCM columns and surrounding soft soil. When DCM column permeability exceeds soil permeability, excess pore pressure dissipation rate shows a remarkable increase compared to that observed when the DCM column permeability is less than or equal to the permeability of surrounding soft soil. [ ]

This paper investigates the contribution of permeability and geosynthetic layer on the vertical load transfer mechanism of the embankment and modelling issues related to application of the embankment load and the properties of the cement-improved columns.

Elasto‐plastic models based on critical state formulations have been successful in describing many of the most important features of the mechanical behaviour of soils. This review paper deals with the applications of this class of models to the numerical analysis of geotechnical problems. After a brief overview of the development of the models, the basic critical state formulation is presented together with the main modifications which have actually been used in computational applications. The problems associated with the numerical implementation of this type of models are then discussed. Finally, a summary of reported computational applications and some specific examples of analyses of geotechnical problems using critical state models are presented.

This paper gives a review of the finite element techniques (FE) applied in the area of material processing. The latest trends in metal forming, non‐metal forming, powder metallurgy and composite material processing are briefly discussed. The range of applications of finite elements on these subjects is extremely wide and cannot be presented in a single paper; therefore the aim of the paper is to give FE researchers/users only an encyclopaedic view of the different possibilities that exist today in the various fields mentioned above. An appendix included at the end of the paper presents a bibliography on finite element applications in material processing for 1994‐1996, where 1,370 references are listed. This bibliography is an updating of the paper written by Brannberg and Mackerle which has been published in Engineering Computations, Vol. 11 No. 5, 1994, pp. 413‐55.

Competition is today forcing companies to increase their effectiveness exploiting synergy and learning in product innovation. Most literature, however, is still mainly focused on how product development projects, seen as isolated efforts, are organised and managed. Basing on preliminary results from the Euro‐Australian co‐operation project CIMA (Euro‐Australian co‐operation centre for Continuous Improvement and innovation MAnagement), this paper proposes a model to explain how companies can gain a substantial competitive advantage by facilitating knowledge generation and transfer during the overall product life‐cycle