Search results

The aim of this paper is to investigate the effect of wing kinematics change on force generation produced by flapping wings.

Forces produced by flapping wings are measured using a load cell and compared for the investigation. The measured forces are validated by estimation using an unsteady blade element theory.

From the measurement and estimation, the authors found that flapping wings produced positive and negative lifts when the wings are attached with the +30° and −30°, respectively.

The authors quantified the characteristics of change in the force generation by flapping wings for three wing kinematics. The wing kinematics was modified by changing the initial wing attachment angle.

The result may be applicable to design of control mechanism for an insect‐mimicking flapping‐wing micro air vehicle, which has only wings without control surfaces at its tail.

The preliminary work may provide an insight for design strategy of flapping‐wing micro air vehicles with compact and handy configurations, because they may perform controlled flight even without control surfaces at their tails.

The work included here is the first attempt to quantify the force generation characteristics for different wing kinematics. The suggested way of wing kinematics change can provide a concept for control mechanism of a flapping‐wing micro air vehicle.

Endurance time is an important factor limiting the progress of flapping-wing aircraft. In this study, this paper developed a prototype of a double-wing flapping-wing micro air vehicle (FMAV) that mimics insect-scale flapping wing for flight. Besides, novel methods for optimal selection of motor, wing length and battery to achieve prolonged endurance are proposed. The purpose of this study is increasing the flight time of double-wing FMAV by optimizing the flapping mechanism, wings, power sources, and energy sources.

The 20.4 g FMAV prototype with wingspan of 21.5 cm used an incomplete gear flapping wing mechanism. The motor parameters related to the lift-to-power ratio of the prototype were first identified and analyzed, then theoretical analysis was conducted to analyze the impact of wing length and flapping frequency on the lift-to-power ratio, followed by practical testing to validate the theoretical findings. After that, analysis and testing examined the impact of battery energy density and efficiency on endurance. Finally, the prototype’s endurance duration was calculated and tested.

The incomplete gear facilitated 180° symmetric flapping. The motor torque constant showed a positive correlation with the prototype’s lift-to-power ratio. It was also found that the prototype achieved the best lift-to-power ratio when using 100 mm wings.

A gear-driven flapping mechanism was designed, capable of smoothly achieving 180° symmetric flapping. Besides, factors affecting long-duration flight – motor, wings and battery – were identified and a theoretical flight duration analysis method was developed. The experimental result proves that the FMAV could achieve the longest hovering time of 705 s, outperforming other existing research on double-wing FMAV for improving endurance.

The purpose of the work is to design a flapping wing that generates net positive propulsive force and vertical force over a flapping cycle operating at a given freestream velocity. In addition, an optimal wing is designed based on the comparison of the force estimated from the quasi‐steady theory, with the wind‐tunnel experiments. Based on the designed wing configuration, a flapping wing ornithopter is fabricated.

This paper presents a theoretical aerodynamic model of the design of an ornithopter with specific twist distribution that results generation of substantial net positive vertical force and thrust over a cycle at non‐zero advance ratio. The wing has a specific but different twist distribution during the downstroke and the upstroke that maintains the designed angle of attack during the strokes. The wing is divided into spanwise strips and Prandtl's lifting line theory is applied to estimate aerodynamic forces with the assumptions of quasi‐steady flow and the wings are without any dihedral or anhedral. Spanwise circulation distribution is obtained and hence lift is calculated. The lift is resolved along the freestream velocity and perpendicular to the freestream velocity to obtain vertical force and propulsive thrust force. Experiments are performed in a wind tunnel to find the forces generated in a flapping cycle which compares well with the theoretical estimation at low flying speeds.

The estimated aerodynamic force indicates whether the wing geometry and operating conditions are sufficient to carry the weight of the vehicle for a sustainable flight. The variation of the aerodynamic forces with varying flapping frequencies and freestream velocities has been illustrated and compared with experimental data that shows a reasonable match with the theoretical estimations. Based on the calculations a prototype has been fabricated and successfully flown.

The theory does not take into account the unsteady effects and estimates the aerodynamic forces at wing level condition. It doesn’t predict stall and ignores structural deformations due to aerodynamic loads. The airfoil section is only specified by the chord, zero lift angle of attack, lift slope, profile drag coefficient and angle of attack as given inputs. To fabricate a light weight wing that maintains a very accurate geometric twist and camber distribution as per the theoretical requirement is challenging.

Useful for designing ornithopter wing (preferably bigger) involving an unswept rigid spar with flapping and twisting.

The novelty of the present wing design is the appropriate spanwise geometric twisting about the leading edge spar.

Flapping-wing vehicles show various advantages as compared to fixed wing vehicles, making flapping-wing vehicles' study necessary in the current scenario. The present study aims to provide guidelines for fixing geometric parameters for an initial engineering design by a simple aerodynamic and flight dynamic parametric study.

A mathematical analysis was performed to understand the aerodynamics and flight dynamics of the micro-air vehicle (MAV). Only the forces due to the flapping wing were considered. The flapping motion was considered to be a combination of the pitching and plunging motion. The geometric parameters of the flapping wing were varied and the aerodynamic forces and power were observed. Attempts were then made to understand the flight stability envelope of the MAV in a forward horizontal motion in the vertical plane with similar parametric studies as those conducted in the case of aerodynamics.

From the aerodynamic study, insights were obtained regarding the interaction of design parameters with the aerodynamics and feasible ranges of values for the parameters were identified. The flapping wing was found to have neutral static stability. The flight dynamic analysis revealed the presence of an unstable oscillatory mode, a stable fast subsidence mode and a neutral mode, in the forward flight of the MAV. The presence of unstable modes highlighted the need for active control to restore the MAV to equilibrium from its unstable state.

The study does not take into account the effects of control surfaces and tail on the aerodynamics and flight dynamics of the MAV. There is also a need to validate the results obtained in the study through experimental means which shall be taken up in the future.

The parametric study helps us to understand the extent of the impact of the design parameters on the aerodynamics and stability of the MAV. The analysis of both aerodynamics and dynamic stability provides a holistic picture for the initial design. The study incorporates complex mathematical equations and simplifies such to understand the aerodynamics and flight stability of the MAV from an engineering perspective.

The study adds to already existing knowledge on the design procedures of a flapping wing.

The purpose of this paper is to demonstrate the uncontrolled vertical takeoff of an insect-mimicking flapping-wing micro air vehicle (FW-MAV) of 12.5 cm wing span with a body weight of 7.36 g after installing batteries and power control.

The forces were measured using a load cell and estimated by the unsteady blade element theory (UBET), which is based on full three-dimensional wing kinematics. In addition, the mean aerodynamic force center (AC) was determined based on the UBET calculations using the measured wing kinematics.

The wing flapping frequency can reach to 43 Hz at the flapping angle of 150°. By flapping wings at a frequency of 34 Hz, the FW-MAV can produce enough thrust to over its own weight. For this condition, the difference between the estimated and average measured vertical forces was about 7.3 percent with respect to the estimated force. All parts for the FW-MAV were integrated such that the distance between the mean AC and the center of gravity is close to zero. In this manner, pitching moment generation was prevented to facilitate stable vertical takeoff. An uncontrolled takeoff test successfully demonstrated that the FW-MAV possesses initial pitching stability for takeoff.

This work has successfully demonstrated an insect-mimicking flapping-wing MAV that can stably takeoff with initial stability.

Bionic flapping-wing aerial vehicles (FWAVs) mimic natural flyers to generate the lift and thrust, such as birds, bats and insects. As an important component of the FWAVs, the flapping wings are crucial for the flight performance. The aim of this paper is to study the effects of different wings on aerodynamic performance.

Inspired by the wings structure of birds, the authors design four cambered wings to analyze the effect of airfoils on the FWAVs aerodynamic performance. The authors design the motor-driven mechanism of flapping wings, and realize the control of flapping frequency. Combined with the wind tunnel equipment, the authors build the FWAVs force test platform to test the static and dynamic aerodynamic performance of different flapping wings under the state variables of flapping frequency, wind speed and inclined angle.

The results show that the aerodynamic performance of flapping wing with a camber of 20 mm is the best. Compared with flat wing, the average lift can be improved by 59.5%.

Different from the traditional flat wing design of FWAVs, different cambered flapping wings are given in this paper. The influence of airfoils on aerodynamic performance of FWAVs is analyzed and the optimal flapping wing is obtained.

Ground effect is one of the important factors in the enhancement of wing aerodynamic performance. This study aims to investigate the aerodynamic forces and performance of a flapping wing with the bending deflection angel under the ground effect.

In this study, the wing and flapping mechanism were designed and manufactured based on the seagull flight and then assembled. It is worth noting that this mechanism is capable of wing bending in the upstroke flight as big birds. Finally, the model was examined at bending deflection angles of 0° and 107° and different distances from the surface, flapping frequencies and velocities in forward flight in a wind tunnel.

The results revealed that the aerodynamic performance of flapping wings in forward flight improved due to the ground effect. The effect of the bending deflection mechanism on lift generation was escalated when the flapping wing was close to the surface, where the maximum power loading occurred.

Flapping wings have many different applications, such as maintenance, traffic control, pollution monitoring, meteorology and high-risk operations. Unlike fixed-wing micro aerial vehicles, flapping wings are capable of operating in very-low Reynolds-number flow regimes. On the other hand, ground effect poses positive impacts on the provision of aerodynamic forces in the take-off process.

Bending deflection in the flapping motion and ground effect are two influential factors in the enhancement of the aerodynamic performance of flapping wings. The combined effects of these two factors have not been studied yet, which is addressed in this study.

The purpose of this study is to experimentally analyse the effect of flexible and stiffened membrane wings in the lift generation of flapping micro air vehicle (MAV).

This is analysed by the rectangle wing made up of polyethylene terephthalate sheets of 100 microns. MAV is tested for the free stream velocity of 2 m/s, 4 m/s, 6 m/s and k^* of 0, 0.25, 1, 3, 8. This test is repeated for flapping MAV of the free flapping frequency of 2 Hz, 4 Hz, 6 Hz, 10 Hz and 12 Hz.

This study shows that the membrane wing with proper stiffeners can give better lift generation capacity than a flexible wing.

Only a normal force component is measured, which is perpendicular to the longitudinal axis of the model.

In MAVs, the wing structures are thin and light, so the effect of fluid-structure interactions is important at low Reynold’s numbers. This data are useful for the MAV developments.

The effect of chord-wise flexibility in lift generation is the study of the effect of a flexible wing and rigid wing in MAV. It is analysed by the rectangle wing. The coefficient of normal force at different free stream conditions was analysed.

With possible practical application in a micro aerial vehicle (MAV), propulsion characteristics of a flapping wing with modified pitch motion are investigated both theoretically and experimentally in this paper.

Modified pitch motion is defined as a sinusoidal pitch motion with the pitch axis outside the wing chord line. Based on the momentum theory, an analytical model is developed to analyze the propulsion characteristics of the defined flapping wing. Following that, a water tunnel study of the effects of pitch axis distance, pitch frequency, and stream velocity on thrust generation is carried out. Thrust is directly measured using a 1‐D load cell and the flow visualization is captured using a high speed video camera.

It is found that shifting pitch axis outside wing chord line benefits the thrust generation significantly. Positive average thrust is produced at a relatively low frequency and increases almost quadratically with the motion frequency. The effect of stream velocity on the thrust time history is signified but has little effect on the average thrust magnitude.

Compared to other types of flapping wing motions, the proposed flapping can be achieved with simple mechanism and thus has the edge in practicality for propelling MAV or other submarine systems.

The paper provides useful aerodynamic characteristics of a type of flapping wing motion which possesses mechanical simplicity and relatively large thrust generation at low‐flapping frequency. This flapping wing has the potential to provide propulsion for a MAV or other submarine systems.

The purpose of this paper is to present the procedure and results from instrumented flight test performed on the flapping MAVs being developed by the authors. A test is performed using a test measurement system to obtain the real characteristics of the flapping vehicles during their flight.

The test is performed in an indoor flight test facility, equipped with a motion capture system and tracking cameras. Spatial position data are obtained from the vehicles with retro‐reflective tracking markers attached. A quantitative analysis is carried out through the investigation and interpretation of the test data for the flight performance assessment of the vehicles.

The finding of the analysis addresses that the test enabled the numerical measurement of vehicles' flying performance and shows the present vehicles have combined characteristics of both birds and insects.

The test metrics attempted in the present study are applicable to the test and evaluation of general flapping micro air vehicles. Thus, this testing method will be useful for the development of future micro air vehicle system.

Full‐scale instrumented flight test and measurement of performance parameters of flapping micro air vehicles other than visual observation are unprecedented and expected to present the guideline of systematic test and evaluation of flapping micro air vehicles.