Search results

In this study, 2D density-based SST K-turbulence model with compressibility effect is used to observe the flow separation and shock wave interactions of the flow. The wall static pressure and Mach number differences are also evaluated. This study aims to discuss the aforementioned objectives

This study outlines the evaluation of the performance of a 2D convergent–divergent nozzle with various triangular jet tab configurations that can be used for effective thrust vectoring of aerial vehicles.

From the study, it is seen that the shadow effect induced by the tab with a height of 30% produces higher oblique wave deflection and higher thrust deflection at the exit nozzle. The numerical calculation concluded that thrust vector efficiency of 30% jet tab is, 0.46%. In the case of 10% jet tab height the thrust vector efficiency is higher, i.e. 1.647%.

2D study.

The optimization will open up a new focus in TVC that can be implemented for effective attitude control in aircrafts.

Used in future aircrafts.

The influence of shadowing ratio with different tab heights at different Mach numbers has not been reported in the previous studies. Few of the studies on jet tab are focused on the acoustic studies and not pertaining to the aerodynamic aspects. The multi jet configuration, the combination of location, shapes and other parametric analysis have not been covered in the previous studied.

Aero-engine exhaust plume length can be more than the aircraft length, making it easier to detect and track by infrared seeker. Aim of this study is to analyze the effect of free stream Mach number (M_∞) on length of potential core of plume. Also, change in infrared (IR) signature of plume and aircraft surface with variation in elevation angle (θ) is examined.

Convergent divergent (CD) nozzle is located outside the rear fuselage of the aircraft. A two dimensional axisymmetric computational fluid dynamics (CFD) study was carried out to study effect of M_∞ on potential core. The CFD data with aircraft and plume was then used for IR signature analysis. The sensor position is changed with respect to aircraft from directly bottom towards frontal section of aircraft. The IR signature is studied in mid wave IR (MWIR) and long wave IR (LWIR) band.

The potential plume core length and width increases as M_∞ increases. At higher altitudes, the potential core length increases for a fixed M_∞. The plume emits radiation in the MWIR band, whereas the aerodynamically heated aircraft surface emits IR in the LWIR band. The IR signature in the MWIR band continuously decreases as the sensor position changes from directly bottom towards frontal. In the LWIR band the IR signature initially decreases as the sensor moves from the directly bottom to the frontal, as the sensor begins to see the wing leading edges and nose cone, the IR signature in the LWIR band slightly increases.

The novelty of this study comes from the data reported on the effect of free stream Mach number on the potential plume core and variation of the overall IR signature of aircraft with change in elevation angle from directly below towards frontal section of aircraft.

The purpose of this study is to investigate the effect of coaxial swirlers on acoustic emission and reduction of potential core length in jet engines.

The swirlers are introduced in the form of curved vanes with angles varied from 0° to 130°, corresponding to swirl numbers of 0–1.5. These swirlers are fixed in the annular chamber and tested at different nozzle pressure ratios of 2, 4 and 6.

The study finds that transonic tones exist for the nonswirl jet, creating an unfavorable effect. However, these screech tones are eliminated by introducing a swirl jet at the nozzle exit. Weak swirl shows a greater reduction in noise than strong swirl at subsonic conditions. In addition, the introduction of swirl jets at all pressure ratios significantly reduces jet noise and core length in supersonic conditions, mitigating the noise created by shockwaves and leading to screech tone-free jet mixing.

The paper provides valuable insights into the use of coaxial swirlers for noise reduction and core length reduction in jet engines, particularly in supersonic conditions.

This study aims to study the interaction effects between a rectangular supersonic jet with a flat wall computationally using wall length as a parameter. The purpose of this study is to investigate the effect of change in wall length on supersonic core length (SCL) reduction, jet deflection and jet decay behavior.

The design Mach number and aspect ratio at the rectangular exit were 1.8 and 2, respectively. To study the wall length effects on jet-wall interactions, wall length (L_w) was varied as 0.5D_h, 1D_h, 2D_h, 4D_h and 8D_h, where D_h was the hydraulic diameter of the nozzle exit. The flat wall with the matching width of the rectangular exit section of a supersonic nozzle was placed at the nozzle exit such that the supersonic jet grazed past the wall. The studies were carried out at over-expansion [nozzle pressure ratio (NPR) = 4], near optimum expansion (NPR = 6) and under-expansion (NPR = 8) levels.

Results indicated that significant reduction in wall-bounded SCL was noticed in the range of 0.5D_h  ≤  L_w ≤ 1D_h for both over-expansion and under-expansion conditions. At L_w ≥ 4D_h, SCL got enhanced at NPR = 4 and 6 but had a negligible effect at NPR = 8.

Thrust vector control, noise reduction and easy take-off for high-speed aircraft.

The effect of change in flat wall length on interaction characteristics of a rectangular supersonic jet was not studied before in terms of SCL reduction and jet decay behavior.

To present the detailed implementation processes of the IDEAL algorithm for two-dimensional compressible flows based on Delaunay triangular mesh, and compare the performance of the SIMPLE and IDEAL algorithms for solving compressible problems. What’s more, the implementation processes of Delaunay mesh generation and derivation of the pressure correction equation are also introduced.

Programming completely in C++.

Five compressible examples are used to test the SIMPLE and IDEAL algorithms, and the comparison with measurement data shows good agreement. The IDEAL algorithm has much better performance in both convergence rate and stability over the SIMPLE algorithm.

The detail solution procedure of implementing the IDEAL algorithm for compressible flows based on Delaunay triangular mesh is presented in this work, seemingly first in the literature.

This paper aims to model and analyze Jeffery Hamel’s channel flow with the magnetohydrodynamics second-grade hybrid nanofluid. Considering the importance of studying the velocity slip and temperature jump in the boundary conditions of the flow, which leads to results close to reality, this paper intends to analyze the mentioned topic in the convergent and divergent channels that have significant applications.

The examination is conducted on a EG-H_2 O <30%–70%> base fluid that contains hybrid nanoparticles (i.e. SWCNT-MWCNT). To ensure comprehensive results, this study also considers the effects of thermal radiation, thermal sink/source, rotating convergent-divergent channels and magnetic fields. Initially, the governing equations are formulated in cylindrical coordinates and then simplified to ordinary differential equations through appropriate transformations. These equations are solved using the Explicit Runge–Kutta numerical method, and the results are compared with previous studies for validation.

After the validation, the effect of the governing parameters on the temperature and velocity of the second-grade hybrid nanofluid has been investigated by means of various and comprehensive contours. In the following, the issue of entropy generation and its related graphical results for this problem is presented. The mentioned contours and graphs accurately display the influence of problem parameters, including velocity slip and temperature jump. Besides, when thermal radiation is introduced (Rd = +0.1 and Rd = +0.2), entropy generation in convergent-divergent channels decreases by 7% and 14%, respectively, compared to conditions without thermal radiation (Rd = 0). Conversely, increasing the thermal sink/source from 0 to 4 leads to an 8% increase in entropy generation at Q = 2 and a 17% increase at Q = 4 in both types of channels. The details of the analysis of contours and the entropy generation results are fully mentioned in the body of the paper.

There are many studies on convergent and divergent channels, but this study comprehensively investigates the effects of velocity slip and temperature jump and certainly, this geometry with the specifications presented in this paper has not been explored before. Among the other distinctive features of this paper compared to previous works, the authors can mention the presentation of velocity and temperature results in the form of contours, which makes the physical analysis of the problem simpler.