Search results

The main purpose of this paper is to define 2D numerical study and a sensitivity analysis of natural convection heat transfer and entropy generation of Al₂O₃-water nanofluid in a trapezoidal cavity, with considering of the presence of a constant axial magnetic field.

The effects of the three effective parameters, the Rayleigh number, Hartmann number (Ha) and also inclination angle on the heat transfer performance and entropy generation, are investigated using a finite volume approach. The sensitivity analysis of the effective parameters is done utilizing the response surface methodology.

The results obtained showed that the mean Nusselt number and total entropy generation increase with the Rayleigh number. Also, increasing the inclination angle reduces the mean Nusselt number (regardless of the magnetic field). In addition, it is found that the mean Nusselt number increases until Ha = 10 and then decreases by increasing of Ha number, regardless of the inclination angle. The sensitivity of the mean Nusselt number to the Ha number and inclination angle α is negative. It is concluded that to maximize the mean Nusselt number and minimize the entropy generation, simultaneously, the Ha and inclination angle must be 50° and 0°, respectively.

There is no published research in the literature about sensitivity analysis of magneto-hydrodynamic heat transfer and entropy generation in inclined trapezoidal cavity filled with nanofluid.

Natural convection heat transfer analysis can be completed using entropy generation analysis. This study aims to accomplish both the natural convection heat transfer and entropy generation analyses for a hexagonal cavity loaded with Cu-H2O nanoliquid subjected to an oriented magnetic field.

Control volume-based finite element method is applied to solve the non-dimensional forms of governing equations and then, the entropy generation number is computed.

The results portray that both the average Nusselt and entropy generation numbers boost with increasing aspect ratio for each value of the undulation number, while both of them decrease with increasing the undulation number for each amplitude parameter. There is a maximum value for the entropy generation number at a specified value of Hartmann number. Also, there is a minimum value for the entropy generation number at a specified value of angle of the magnetic field. When the volume fraction of nanoparticles grows, the average Nusselt number increases and the entropy generation number declines. The entropy generation number attains to a maximum value at Ha = 14 for each value of aspect ratio. The average Nusselt number ascends 2.9 per cent and entropy generation number decreases 1.3 per cent for Ha = 0 when ϕ increases from 0 to 4 per cent.

A hexagonal enclosure (complex geometry), which has many industrial applications, is chosen in this study. Not only the characteristics of heat transfer are investigated but also entropy generation analysis is performed in this study. The ecological coefficient of performance for enclosures is calculated, too.

The aim of this paper is to investigate performance improvements of a monolithic solid oxide fuel cell geometry through an entropy generation analysis.

The analysis of entropy generation rates makes it possible to identify the phenomena that cause the main irreversibilities in the fuel cell, to understand their causes and to propose changes in the design and operation of the system. The various contributions to entropy generation are analyzed separately in order to identify which geometrical parameters should be considered as the independent variables in the optimization procedure. The local entropy generation rates are obtained through 3D numerical calculations, which account for the heat, mass, momentum, species and current transport. The system is then optimized in order to minimize the overall entropy generation and increase efficiency.

In the optimized geometry, the power density is increased by about 10 per cent compared to typical designs. In addition, a 20 per cent reduction in the fuel cell volume can be achieved with less than a 1 per cent reduction in the power density with respect to the optimal design.

The physical model is based on a simple composition of the reactants, which also implies that no chemical reactions (water gas shift, methane steam reforming, etc.) take place in the fuel cell. Nevertheless, the entire procedure could be applied in the case of different gas compositions.

Entropy generation analysis allows one to identify the geometrical parameters that are expected to play important roles in the optimization process and thus to reduce the free independent variables that have to be considered. This information may also be used for design improvement purposes.

In this paper, entropy generation analysis is used for a multi‐physics problem that involves various irreversible terms, with the double use of this physical quantity: as a guide to select the most relevant design geometrical quantities to be modified and as objective function to be minimized in the optimization process.

The aim of this article is to present the results of a parametric analysis of the entropy generation due to mixed convection in the entry‐developing region between two differentially heated isothermal vertical plates.

The entropy generation was estimated via a numerical solution of the mass, momentum and energy conservation equations governing the flow and heat transfer in the vertical channel between the two parallel plates. The resultant temperature and velocity profiles were used to estimate the entropy generation and other heat transfer parameters over a wide range of the operating parameters. The investigated parameters include the buoyancy parameter (Gr/Re), Eckert number (Ec), Reynolds number (Re), Prandtl number (Pr) and the ratio of the dimensionless temperature of the two plates (θ_T).

The optimum values of the buoyancy parameter (Gr/Re) optimum at which the entropy generation assumes its minimum for the problem under consideration have been obtained numerically and presented over a wide range of the other operating parameters. The effect of the other operating parameters on the entropy generation is presented and discussed as well.

The results of this investigation are limited to the geometry of vertical channel parallel plates under isothermal boundary conditions. However, the concept of minimization of entropy generation via controlling the buoyancy parameter is applicable for any other geometry under any other thermal boundary conditions.

The results presented in this paper can be used for optimum designs of heat transfer equipment based on the principle of entropy generation minimization with particular focus on the optimum design of plate and frame heat exchanger and the optimization of electronic packages and stacked packaging of laminar‐convection‐cooled printed circuits.

This paper introduces the entropy generation minimization via controlling the operating parameters and clearly identifies the optimum buoyancy parameter (Gr/Re) at which entropy generation assumes its minimum under different operating conditions.

The purpose of this paper is to examine the flow, heat transfer and entropy generation characteristics for an inclined channel of two immiscible micropolar fluids.

The flow region consists of two zones, the flow of the heavier fluid taking place in the lower zone. The flow is assumed to be governed by Eringen’s micropolar fluid flow equation. The resulting governing equations are then solved using the homotopy analysis method.

The following findings are concluded: first, the entropy generation rate is more near the plates in both the zones as compared to that of the interface. This indicates that the friction due to surface on the fluids increases entropy generation rate. Second, the entropy generation rate is more near the plate in Zone I than that of Zone II. This may be due to the fact that the fluid in Zone I is more viscous. This indicates the more the viscosity of the fluid is, the more the entropy generation. Third, Bejan number is the maximum at the interface of the fluids. This indicates that the amount of exergy (available energy) is maximum and irreversibility is minimized at the interface between the fluids. Fourth, as micropolarity increases, entropy generation rate near the plates decreases and irreversibility decreases. This indicates an important industrial application for micropolar fluids to use them as a good lubricant.

The problem is original as no work has been reported on entropy generation in an inclined channel with two immiscible micropolar fluids.

Microfluidics is one of the interesting areas of the research in thermal and engineering fields due to its wide range of applications in a variety of heat transport problems such as micromixers, micropumps, cooling systems for microelectromechanical systems (MEMS) micro heat exchangers, etc. Lower cost with better thermal performance is the main objective of these devices. Therefore, in this study, the entropy generation in an electrically conducting Casson fluid flow through an inclined microchannel with hydraulic slip and the convective condition hves been numerically investigated. Aspects of viscous dissipation, natural convection, joule heating, magnetic field and uniform heat source/sink are used

Suitable non-dimensional variables are used to reduce the non-linear system of ordinary differential equations, and then this system is solved numerically using Runge-Kutta-Fehlberg fourth fifth order method along with shooting technique. The obtained numerical solutions of the fluid velocity and temperature are used to characterize the entropy generation and Bejan number. Also, the Nusselt number and skin friction coefficient for various values of parameters are examined in detail through graphs. The obtained present results are compared with the existing one which is perfectly found to be in good agreement.

It is established that the production of the entropy can be improved with the aspects of joule heating, viscous dissipation and internal heat source/sink. The entropy generation enhances for increasing values of Casson Parameter (β) and Biot number (Bi). Furthermore, it is interestingly noticed that the enhancement of Reynolds number and uniform heat source/sink shows the dual behaviour of the entropy generation due to significant influence of the viscous forces in the region close to the channel walls. It was observed that increasing behaviour of the heat transfer rate for enhancement values of the Eckert number and heat source/sink ratio parameter and the drag force are retarded with higher estimations of Reynolds number.

Entropy generation analysis on MHD Casson fluid flow through an inclined microchannel with the aspects of convective, Joule heating, viscous dissipation, magnetism, hydraulic slip and internal heat source/sink has been numerically investigated.

This study aims to expose the flow phenomena and entropy generation during a; magnetohydrodynamic (MHD) Poiseuille flow of water-based nanofluids (NFs) in a porous channel subject to hydrodynamic slip and convective heating boundary conditions. The flow caused by the uniform pressure; gradient between infinite parallel plates is considered steady and fully developed. The nanoparticles; namely, copper, alumina and titanium oxide are taken with pure water as the base fluid. Viscous dissipation and Joule heating impacts are also incorporated in this investigation.

The reduced governing equations are solved analytically in closed form. The physical insights of noteworthy parameters on the important flow quantities are demonstrated through graphs and analyzed elaborately. The thermodynamic analysis is performed by calculating entropy generation; rate and Bejan number. A graphical comparison between solutions corresponding to NFs and regular fluid in the channel is also provided.

The analysis of the results divulges that entropy generation minimization can be achieved by an appropriate combination of the geometrical and physical parameters of thermomechanical systems. It is reported that ascent in magnetic parameter number declines the velocity profiles, while the inverse pattern is witnessed with augmentation in hydrodynamic slip parameters. The temperature dissemination declines with the growth of Biot numbers. It is perceived that the entropy generation rate lessens with an upgrade in magnetic parameter, whereas the reverse trend of Bejan number is perceived with expansion in magnetic parameter and Biot number. The important contribution of the result is that the entropy generation rate is controlled with an appropriate composition of thermo-physical parameter values. Moreover, in the presence of a magnetic field and suction/injection at the channel walls, the shear stresses at the channel walls are reduced about two times.

In various industrial applications, minimizing entropy generation plays a significant role. Miniaturization of entropy is the utilization of the energy of thermal devices such as micro heat exchangers, micromixers, micropumps and cooling microelectromechanical devices.

An attentive review of the literature discloses that quite a few studies have been conducted on entropy generation analysis of a fully developed MHD Poiseuille flow of NFs through a permeable channel subject to the velocity slip and convective heating conditions at the walls.

The purpose of this paper is to present a numerical analysis of the flow and heat transfer in a tube with a wire coil insert. A second law analysis of the results is accounted for, in order to assess the local and overall entropy generation in relation with the increased pressure drop and convective heat transfer. A wire coil with p/D=1.25 and e/D=0.076 is selected as insert device. A Reynolds number range between 100 and 1,000 is investigated, which corresponds to the typical operating regimes in the risers of liquid solar collectors. Different wall heat fluxes and inclination angles allow to analyze the potential impact of mixed convection in the presence of tube inserts.

Three-dimensional numerical simulations are performed using a finite-volume solver, assuming laminar flow conditions. Pure water and a mixture of water and propylene-glycol (20 percent) are used as working fluids, with temperature-dependent properties. Fanning friction factor, Nusselt number and local entropy generation results are obtained in the fully developed region.

The friction factor results are successfully compared with a well-known experimental correlation for wire coil inserts. The earlier onset of transition is devised at Re > 300. Nusselt number augmentations between 2.5- and 6-fold are reported with respect to the smooth tube. The mixed convection regime encountered in the smooth tube for the operating conditions investigated is canceled in the wire coiled tube, owing to the opposed effect of the swirl flow induced and the bouyancy forces. Frictional, heat transfer and overall entropy generation rates are computed locally in the fully developed region, allowing to relate these results with the flow structures in the mixed convection smooth tube and in the wire coiled tube. A threefold decrease in the entropy generation rate is reported for tubes with wire coil inserts.

An holistic understanding of the heat transfer enhancement in tubes with wire coil inserts is provided through the analysis of the flow pattern, Fanning friction factor, Nusselt number and local entropy generation rates. The reduced entropy generation in the enhanced tube serves as a performance criteria to confirm the positive effect of wire coil inserts in heat transfer for the operating regime under investigation, in spite of the increased pressure drop.

This paper aims to study numerically the steady natural convective heat transfer of a hybrid nanosuspension (Ag-MgO/H2O) within a partially heated/cooled trapezoidal region with linear temperature profiles at inclined walls under an effect of uniform Lorentz force. This investigation is useful for researchers studying in the area of cavity flows to know features of the flow structures and nature of hybrid nanofluid characteristics. In addition, a detailed entropy generation analysis has been performed to highlight possible regimes with minimal entropy generation rates.

The governing equations formulated using the Oberbeck–Boussinesq approach and single-phase nanoliquid model are transformed to a non-dimensional form by using non-dimensional variables. The obtained equations with appropriate boundary conditions are resolved by the finite difference technique. The developed code has been validated comprehensively. Analysis has been performed for a wide range of governing parameters, including Rayleigh number (Ra = 105), Prandtl number (Pr = 6.82), Hartmann number (Ha = 0–100), magnetic field inclination angle (φ = 0–?/2) and nanoparticles volume fraction (φ_hnf = 0 and 2%).

It has been shown that inclined magnetic field can be used to manage the energy transport performance. An inclusion of nanoparticles without Lorentz force influence allows forming more stable convective regime with descending heat plume in the central zone, while such a regime was performed for clear fluid only for moderate and high Hartmann numbers. Moreover, the average overall entropy generation can be decreased with a growth of the Hartmann number, while an addition of hybrid nanoparticles allows reducing this parameter for Ha = 30 and 50. The average Nusselt number can be increased with a growth of the nanoparticles concentration for low values of the magnetic field intensity.

Governing equations written using the conservation laws and dimensionless non-primitive variables have been resolved by the finite difference approach. The created numerical code has been verified by applying the grid independence test and computational outcomes of other researchers. The comprehensive analysis for various key parameters has been performed.

Thermo-magnetic convective flow analysis under the impact of thermal radiation for heat and entropy generation phenomena is an active research field for understanding the efficiency of thermodynamic systems in various engineering sectors. This study aims to examine the characteristics of convective heat transport and entropy generation within an inverted T-shaped porous enclosure saturated with a hybrid nanofluid under the influence of thermal radiation and magnetic field.

The mathematical model incorporates the Darcy-Forchheimer-Brinkmann model and considers thermal radiation in the energy balance equation. The complete mathematical model has been numerically simulated through the penalty finite element approach at varying values of flow parameters, such as Rayleigh number (Ra), Hartmann number (Ha), Darcy number (Da), radiation parameter (Rd) and porosity value (e). Furthermore, the graphical results for energy variation have been monitored through the energy-flux vector, whereas the entropy generation along with its individual components, namely, entropy generation due to heat transfer, fluid friction and magnetic field, are also presented. Furthermore, the results of the Bejan number for each component are also discussed in detail. Additionally, the concept of ecological coefficient of performance (ECOP) has also been included to analyse the thermal efficiency of the model.

The graphical analysis of results indicates that higher values of Ra, Da, e and Rd enhance the convective heat transport and entropy generation phenomena more rapidly. However, increasing Ha values have a detrimental effect due to the increasing impact of magnetic forces. Furthermore, the ECOP result suggests that the rising value of Da, e and Rd at smaller Ra show a maximum thermal efficiency of the mathematical model, which further declines as the Ra increases. Conversely, the thermal efficiency of the model improves with increasing Ha value, showing an opposite trend in ECOP.

Such complex porous enclosures have practical applications in engineering and science, including areas like solar power collectors, heat exchangers and electronic equipment. Furthermore, the present study of entropy generation would play a vital role in optimizing system performance, improving energy efficiency and promoting sustainable engineering practices during the natural convection process.

To the best of the authors’ knowledge, this study is the first ever attempted detailed investigation of heat transfer and entropy generation phenomena flow parameter ranges in an inverted T-shaped porous enclosure under a uniform magnetic field and thermal radiation.