Search results

Optimised concrete components are often of complex geometries, which are difficult and costly to cast using traditional formworks. This paper aims to propose an innovative formwork system for optimised concrete casting, which is eco-friendly, recyclable and economical.

In the proposed formwork system, ice is used as mould pattern to create desired geometry for concrete member, then sand mould is fabricated based on the ice pattern. A mix design and a mixing procedure for the proposed sand mould are developed, and compression tests are also performed to ensure sufficient strength of the sand mould. Furthermore, surface preparation of the sand mould is investigated for easy demoulding and for achieving good concrete surface quality. Additionally, recyclability of the proposed sand mould is tested.

The proposed mix design and mixing procedure can provide sufficient strength for sand mould in concrete casting. The finished components exhibit smooth surfaces and match designed geometries, and the proposed sand mould can be fully recycled with satisfactory strength.

To the best of the authors’ knowledge, this is the first study that combines ice pattern and sand mould to create recyclable formwork system for concrete casting. The new techniques developed in this research has great potential to be applied in the fabrication of large-scale concrete structures with complex geometries.

Irregularly shaped architectural designs with surfaces curved in multiple directions, known as free-form designs, have gained significant public interest in recent decades. However, it is challenging to convert complex designs into real structures. This paper aims to realize free-form construction by developing a novel workflow in which additively manufactured thermoplastic polyurethane (TPU) molds are used.

The workflow is developed through mechanical tests on additively manufactured TPU specimens, determination of TPU mold design criteria and exploration of mold preparation methods. Two concrete elements with free-form geometries are fabricated using the proposed workflow.

TPU is a thermoplastic elastomer that is strong and inexpensive, making it an ideal mold material for casting complex concrete structures. An innovative workflow is developed in which TPU molds are used, appropriate release agents are selected for different concrete casting conditions and a mold subdivision method is proposed to facilitate the demolding process. Furthermore, the integrity of TPU molds can be maintained by following the proposed workflow, enabling repetitive use of molds. The fabrication of the two free-form structures shows that complex concrete members with high dimensional accuracy and excellent surface quality can be manufactured using the proposed method.

To the best of the authors’ knowledge, this is the first systematic study on using additively manufactured TPU molds for concrete casting of complex structures. The new techniques developed in this research can be applied to large-scale architectural, engineering and construction projects.

The influence of using magnetic water instead of tap water in the mechanical properties of the concrete exposed to elevated temperatures was investigated. Two concrete mixes were used and cast with the same ingredients. Tap water was used in the first mix and magnetic water was used in the second mix. A total of 48 specimens were cast and divided as follows: 16 cylinders for the concrete compressive strength test (8 samples for each mix), 16 cylinders for the splitting tensile strength (8 specimens for each mix) and 16 beams to test the influences of magnetized water on the flexural strength of concrete (8 specimens for each mixture). Specimens were exposed to temperatures of (25 °C, 200 °C, 400 °C and 600 °C). The experimental results showed that magnetic water highly affected the mechanical properties of concrete. Specimens cast and curried out with magnetic water show higher compressive strength, splitting tensile strength and flexural strength compared to normal water specimens at all temperatures. The relative strength range between the two types of water used was 110–123% for compressive strength and 110–133% for splitting strength. For the center point loading test, the relative flexural strength range was 118–140%. The use of magnetic water in mixing concrete contribute to a more complete hydration process.

Experimental study was carried out on two concrete mixes to investigate the effect of magnetic water. Mix#1 used normal water as the mixing water, and Mix#2 used magnetic water instead of normal water. After 28 days, all the samples were taken out of the tank and left to dry for seven days, then they were divided into different groups. Each group was exposed to a different temperature where it was placed in a large oven for two hours. Three different tests were carried out on the samples, these tests were concrete compressive strength, flexural strength and splitting tensile strength.

Exposure of concrete to high temperatures had a significant influence on concrete mechanical properties. Specimens prepared using magnetic water showed higher compressive strength at all temperature levels. The use of magnetic water in casting and curing concrete can increase the compressive strength by 23%. Specimens prepared using magnetic water show higher splitting tensile strength at all temperatures up to 33%. The use of magnetic water in casting and curing can strengthen and increase concrete resistance to high temperatures, a significant enhancement in flexural strength at all temperatures was found with a value up to 40%.

Previous research proved the advantages of using magnetic water for improving the mechanical properties of concrete under normal conditions. The potential of using magnetic water in the concrete industry in the future requires conducting extensive research to study the behavior of magnetized concrete under severe conditions to which concrete structures may be subjected to. These days, there are attempts to obtain stronger concrete with high resistance to harsh environmental conditions without adding new costly ingredients to its main mixture. No research has been carried out to investigate the effect of magnetic water on the mechanical properties of concrete exposed to elevated temperature. The main objective of this study is to evaluate the effect of using magnetic water on the mechanical properties of hardened concrete subjected to elevated temperature.

Concrete, the second most used material in the world, surpassed only by water, relies on a vast amount of cement. The process of cement production emits substantial amounts of carbon dioxide (CO₂). Consequently, it is crucial to search for cement alternatives. Geopolymer concrete (GC) uses industrial by-product material instead of traditional cement, which not only reduces CO₂ emissions but also enhances concrete durability. On the other hand, the disposal of concrete waste in the landfills represents a significant environmental challenge, emphasising the urgent need for sustainable solutions. This study aimed to investigate waste concrete's best form and rate as the alternative aggregates in self-compacting and ambient-cured GC to preserve natural resources, reduce construction and demolition waste and decrease pertinent CO₂ emissions. The binding material employed in this research encompasses fly ash, slag, micro fly ash and anhydrous sodium metasilicate as an alkali activator. It also introduces the best treatment method to improve the recycled concrete aggregate (RCA) quality.

A total of25%, 50% and 100% of coarse aggregates are replaced with RCAs to cast self-compacting geopolymer concrete (SCGC) and assess the impact of RCA on the fresh, hardened and water absorption properties of the ambient-cured GC. Geopolymer slurry was used for coating RCAs and the authors examined the effect of one-day and seven-day cured coated RCA. The mechanical properties (compressive strength, splitting tensile strength and modulus of elasticity), rheological properties (slump flow, T500 and J-ring) and total water absorption of RCA-based SCGC were studied. The microstructural and chemical compositions of the concrete mixes were studied by the methods of energy dispersive X-Ray and scanning electron microscopy.

It is evident from the test observations that 100% replacement of natural aggregate with coated RCA using geopolymer slurry containing fly ash, slag, micro fly ash and anhydrous sodium metasilicate cured for one day before mixing enhances the concrete's quality and complies with the flowability requirements. Assessment is based on the fresh and hardened properties of the SCGC with various RCA contents and coating periods. The fresh properties of the mix with a seven-day curing time for coated RCA did not meet the requirements for self-compacting concrete, while this mix demonstrated better compressive strength (31.61 MPa) and modulus of elasticity (15.39 GPa) compared to 29.36 MPa and 9.8 GPa, respectively, for the mix with one-day cured coated RCA. However, incorporating one-day-cured coated RCA in SCGC demonstrated better splitting tensile strength (2.32 MPa) and water absorption (15.16%).

A potential limitation of this study on SCGC with coated RCAs is the focus on the short-term behaviour of this concrete. This limited time frame may not meet the long-term requirements for ensuring the sustained durability of the structures throughout their service life.

This paper highlights the treatment technique of coating RCA with geopolymer slurry for casting SCGC.

Three-dimensional printing of concrete (3DPC) has a potential for the rapid industrialization of the housing sector, with benefits of reduced construction time due to no formwork requirement, ease of construction of complex geometries, potential high construction quality and reduced waste. Required materials adaption for 3DPC is within reach, as concrete materials technology has reached the point where performance-based specification is possible by specialists. This paper aims to present an overview of the current status of 3DPC for construction, including existing printing methods and material properties required for robustness of 3DPC structures or structural elements.

This paper has presented an overview of three categories of 3DPC systems, namely, gantry, robotic and crane systems. Material compositions as well as fresh and hardened properties of mixes currently used for 3DPC have been elaborated.

This paper presents an overview of the state of the art of 3DPC systems and materials. Research needs, including reinforcement in the form of bars or fibres in the 3D printable cement-based materials, are also addressed.

The critical analysis of the 3D concrete printing system and materials described in this review paper is original.

The purpose of this paper is to investigate the effect of the replacement of natural coarse aggregate (NCA) with different percentages of recycled coarse aggregate (RCA) on properties of low calcium fly ash (FA)-based geopolymer concrete (GPC) cured at oven temperature. Further, this paper aims to study the effect of partial replacement of FA by ground granulated blast slag (GGBS) in GPC made with both NCA and RCA cured under ambient temperature curing.

M25 grade of ordinary Portland cement (OPC) concrete was designed according to IS: 10262-2019 with 100% NCA as control concrete. Since no standard guidelines are available in the literature for GPC, the same mix proportion was adopted for the GPC by replacing the OPC with 100% FA and W/C ratio by alkalinity/binder ratio. All FA-based GPC mixes were prepared with 12 M of sodium hydroxide (NaOH) and an alkalinity ratio, i.e. sodium hydroxide to sodium silicate (NaOH:Na₂SiO₃) of 1:1.5, subjected to 90^°C temperature for 48 h of curing. The NCA were replaced with 50% and 100% RCA in both OPC and GPC mixes. Further, FA was partially replaced with 15% GGBS in GPC made with the above percentages of NCA and RCA, and they were given ambient temperature curing with the same molarity of NaOH and alkalinity ratio.

The workability, compressive strength, split tensile strength, flexural strength, water absorption, density, volume of voids and rebound hammer value of all the mixes were studied. Further, the relationship between compressive strength and other mechanical properties of GPC mixes were established and compared with the well-established relationships available for conventional concrete. From the experimental results, it is found that the compressive strength of GPC under ambient curing condition at 28 days with 100% NCA, 50% RCA and 100% RCA were, respectively, 14.8%, 12.85% and 17.76% higher than those of OPC concrete. Further, it is found that 85% FA and 15% GGBS-based GPC with RCA under ambient curing shown superior performance than OPC concrete and FA-based GPC cured under oven curing.

The scope of the present paper is limited to replace the FA by 15% GGBS. Further, only 50% and 100% RCA are used in place of natural aggregate. However, in future study, the replacement of FA by different amounts of GGBS (20%, 25%, 30% and 35%) may be tried to decide the optimum utilisation of GGBS so that the applications of GPC can be widely used in cast in situ applications, i.e. under ambient curing condition. Further, in the present study, the natural aggregate is replaced with only 50% and 100% RCA in GPC. However, further investigations may be carried out by considering different percentages between 50 and 100 with the optimum compositions of FA and GGBS to enhance the use of RCA in GPC applications. The present study is further limited to only the mechanical properties and a few other properties of GPC. For wider use of GPC under ambient curing conditions, the structural performance of GPC needs to be understood. Therefore, the structural performance of GPC subjected to different loadings under ambient curing with RCA to be investigated in future study.

The replacement percentage of natural aggregate by RCA may be further enhanced to 50% in GPC under ambient curing condition without compromising on the mechanical properties of concrete. This may be a good alternative for OPC and natural aggregate to reduce pollution and leads sustainability in the construction.

Additive lamination manufacturing (ALM), as a novel additive manufacturing technology, builds up the geometry via the lamination of fiber-reinforced polymer (FRP) fabric laterally, rendering it suitable for fabricating large-scale Stay-in-Place concrete formwork. This paper aims to investigate the control parameters and structure performance of ALM and assess its application for the fabrication of large-scale concrete formwork.

Based on previous feasibility studies, this research systematically investigates the control and material parameters that influence horizontal and vertical extrusion speeds, as well as the overall quality of ALM. Once the system parameters are established, a series of prototypes are fabricated and tested to validate the tensile strength of the formwork and its reinforcement capabilities. In addition, this study assesses the potential geometric freedom and implementation constraints of ALM.

This research identifies the essential control parameters for path planning in ALM and examines their impact on fabrication. In addition, this paper evaluates ALM’s strengths and limitations in producing concrete formwork for large-scale concrete structures, comparing these to industry benchmarks.

A critical challenge in additive manufacturing lies in its scalability and compatibility with existing construction processes. In comparison to concrete, FRP offers advantages such as being lighter, easier to handle and providing surface protection and reinforcement. These qualities make FRP superior for formwork and compatible with existing building standards. Despite its advantages and potential, the current path planning and control model in 3D printing do not apply to ALM due to its novel build-up process. Also, the performance of fabricated parts as part of integrated large-scale structures is yet to be studied.

The purpose of this paper is to concern with using municipal solid waste incineration bottom ash (MSWI-BA) in concrete application.

In this paper, the performance of reinforced concrete (RC) beams containing MSWI-BA was investigated. Four concrete mixes were used in this study. The control mix had a proportion of 1 (cement): 2 (fine aggregates): 4 (coarse aggregates) by weight. In the other three mixes, the fine aggregates were partially replaced with 20%, 40% and 60% MSWI-BA (by weight). The water to cement ratio was kept constant at 0.5 in all mixes. Concrete cubes and cylinders were prepared to determine some physical and mechanical properties of concrete, whereas RC beams were used for determining the structural performance.

There was an increase in compressive strength, tensile strength and the modulus of elasticity when 20% of fine aggregates were replaced with MSWI-BA. However, beyond 20% these properties were reduced. The load bearing capacity and deflection were the highest for the control beam and the beam with 20% MSWI-BA.

The research conducted in this investigation used a specific type of MSWI-BA. The composition of the waste can vary from one plant to another and this presents one of the limitations.

The findings of this research indicate that MSWI-BA can partially substitute fine aggregate, thus reducing the impact of construction on the environment.

The MSWI-BA used in this research differs from other types as the waste papers and cartons are removed from the waste and used to produce other products. Therefore, this study is considered original as it examines MSWI-BA with different properties for use in construction.

This study aims to make an effort to develop a model to predict the residual flexural strength of reinforced concrete beams subjected to reinforcement corrosion.

For generating the required data to develop the model, a set of experimental variables was considered that included corrosion current density, corrosion duration, rebar diameter and thickness of concrete cover. A total of 28 sets of reinforced concrete beams of size 150 × 150 × 1,100 mm were cast, of which 4 sets of un-corroded beams were tested in four-point bend test as control beams and the remaining 24 sets of beams were subjected to accelerated rebar corrosion inducing different levels of corrosion current densities for different durations. Corroded beams were also tested in flexure, and test results of un-corroded and corroded beams were utilized to obtain an empirical model for estimating the residual flexural strength of beams for given corrosion current density, corrosion duration and diameter of the rebars.

Comparison of the residual flexural strengths measured experimentally for a set of corroded beams, reported in literature, with that predicted using the model proposed in this study indicates that the proposed model has a reasonably good accuracy.

The empirical model obtained under this work can be used as a simple tool to predict residual flexural strength of corroded beams using the input data that include rebar corrosion rate, corrosion duration after initiation and diameter of rebars.

This study aimed to investigate the suitability and cost-benefit of using copper tailings as partial replacement of sand in concrete production. The study was motivated by the accumulation and non-use of copper tailings in dams among them tailing dam 25 also known as TD 25 in Kitwe city of the Copperbelt province in Zambia that take up approximately 111 hectares of unused land.

Laboratory experimental approach of concrete production based on water/cement ratios of 0.3 and 0.5 was used because this was an exploratory study designed to establish the primary performance of concrete. In total, 30 concrete cubes were cast based on the two water-cement ratios. In total, 0% to 30% partial sand replacement with copper tailings was used in both mixes with the 0% copper tailings replacement being the control mix and reference point. Other concrete tests included workability, density, compressive strength and element composition analysis.

Results revealed that copper tailings from TD 25 were suitable for partial replacement of sand in concrete. Thirty per cent of sand replacement with copper tailings was established as the maximum replacement amount to produce optimum compressive strength values from both mixes. The drier mix of 0.3 water-cement ratios produced higher compressive strength results of 23 MPa at 28 days of concrete curing with 2.34% as optimum concrete cost reduction.

The research results provide the cost-benefit analysis and savings that can be attained from using cheaper copper tailings based concrete. The study further provided the quantity of land available for development arising from absorption of copper tailings as a sustainable construction material. The local authority now has statistics and numerical values that it can use to absorb copper tailings as a concrete raw material.

The study provides guidance on optimum concrete grade produced and cost reduction details of copper tailing-based concrete to support for local authorities in suitable land wand waste management using real data.