Search results

The development of strategies for energy efficiency optimization in buildings has become a fundamental way to reduce buildings’ environmental impact because the amount of energy consumed by buildings is responsible for one‐third of total global energy consumption. The purpose of this research is to evaluate the performance of buildings in terms of their indoor operative temperature dynamics considering the impact of other neighbouring buildings. The goal of the paper is to verify whether close spatial relationships of buildings and urban morphology within a local network of buildings could cause a considerable effect on indoor thermal behaviour.

The authors simulated buildings in an existing city block in Albany, New York, USA. The block consisted of six single‐family houses.

The results demonstrate that buildings mutually impact the indoor thermal behaviour of other buildings in the network with indoor operative temperature differences of over 20 percent in summer and over 40 percent in winter for the test case examined. The research also compares this result with improvements in indoor operative temperature achieved through traditional envelope improvements. It was found that during the summer, certain envelope improvement strategies have nearly the same impact in terms of indoor thermal behaviour. During winter, the presence of neighbouring buildings causes a variation that is more than double the value of the effect caused by a typical envelope modification.

It is concluded that this mutual impact on indoor operative temperature across spatially proximal buildings should be included in dynamic analyses of buildings. Future research should examine the effect of these indoor operative temperature deviations on the energy performance predictions of buildings in urban and quasi‐urban settings.

Where buildability is concerned, the six total building performance (TBP) mandates are seldom taken into consideration.. The purpose of this paper is to examine the relationship between buildability and the two TBP mandates of thermal performance and building integrity performance.

A real life case study of a worker dormitories building project was used as the base model for analysis. A breakdown of the buildability scores for the project was first noted. Thereafter, the TBP guidelines relating to thermal performance and building integrity performance were incorporated into the base model and the buildability scores were recomputed.

Following the thermal performance guidelines, a negative relationship with buildability was observed. However, a positive result was established between the building integrity performance guidelines and buildability. The different relationships occurred due to the different aspects of the base model that needed to be changed to conform to the guidelines for both mandates.

It appears that the incorporation of guidelines for any one of the six TBP mandates will yield different results depending on the situation. This was the case for both thermal performance and building integrity performance in the present study.

The paper establishes the relationship between the TBP mandates of thermal performance, building integrity performance and buildability for the first time, which is beneficial to building designers.

This paper investigates thermal mass performance (TMP) in hot climates. The impact of using precast concrete (PC) as a core envelope with different insulation materials has been studied. The aim is to find the effect of building mass with different weights on indoor energy consumption, specifically cooling load in hot climates.

This research adopted a case study and simulation methods to find out the efficiency of different mass performances in hot and humid climate conditions. Different scenarios of light, moderate and heavyweight mass using PC have been developed and simulated. The impact of these scenarios on indoor cooling load has been investigated using the integrated environment solution-virtual environment (IES-VE) software.

The results showed that adopting a moderate weight mass of two PC sheets and a cavity layer in between can reduce indoor air temperature by 1.17 °C; however, this type of mass may increase the cooling demand. On the other hand, it has been proven that adopting a heavyweight mass for building envelopes and increasing the insulation material has a significant impact on reducing the cooling load. Using a PC Sandwich panel and increasing the insulation material layers for external walls and thickness by 50 mm will reduce the cooling load by 15.8%. Therefore, the heavyweight mass is more efficient compared to lightweight and moderate mass in hot, humid climate areas such as the UAE, in spite of the positive indoor TMP that can be provided by the lightweight mass in reducing the indoor air temperature in the summer season.

This research contributes to the thermal mass concept as one of these strategies that have recently been adopted to optimize the thermal performance of buildings and developments. Efficient TMP can have a massive impact on reducing energy consumption. However, less work has investigated TMP in hot and humid climate conditions. Furthermore, the impact of the PC on indoor thermal performance within hot climate areas has not been studied yet. The findings of this study on TMP in the summer season can be generated in all hot climate zones, and investigating the TMP in other seasons can be extended in future studies.

Although vacuum insulation panels (VIPs) are thermal insulators that combine high thermal performance with limited thickness, application in the building sector is still rare due to lack of scientific knowledge on the behaviour of these panels applied in building constructions. This paper, therefore, seeks to give an overview of the requirements for and the behaviour of VIPs integrated into building components and constructions. Moreover, the interaction between different requirements on and properties of these integrated components are discussed in detail, since a desired high quality of the finished product demands an integral approach regarding all properties and requirements, especially during the design phase. Therefore, the importance of an integral design approach to application of VIPs is shown and emphasized in this paper.

To achieve this objective, the legally and technically required properties of VIPs and especially their interrelationships have been studied, resulting in a relationship diagram. Based on these investigations of thermal‐ , service life‐ and structural‐properties have been selected to be studied more elaborately using experimental set‐up for structural testing and simulation software for thermal and hygrothermal testing.

Two relationships between requirements or properties were found to be of principal importance for the design of façade components in which VIPs are integrated. First, thermal performance requirements strongly interact with structural performance, principally through the edge spacer of this façade component. A high thermal performance requires minimization of the thermal edge effect, in most cases reducing the structural performance of the entire panel. Second, an important relationship between thermal performance and service life has been recognised. The operating phenomenon mainly governing this interaction is thermal conductivity aging.

Most research in the field of vacuum insulation until now has been directed towards gaining knowledge on specific properties of the product, especially on thermal and hygrothermal properties. The relationships and interactions between these properties and the structural behaviour, however, have been neglected. This paper, therefore, addresses the need for an integral design (and study) approach for the application of VIPs in architectural constructions.

This paper aims to investigate the thermal comfort practices in four non-domestic buildings and explores how the organisational context affects the actions and practices of occupants and facilities managers.

The study applied qualitative methods and post-occupancy evaluation methodologies to investigate the thermal practices in four case studies. A combination of qualitative and quantitative methodologies was deployed, namely, semi-structured interviews, questionnaires, observation and monitoring studies of building performance.

The concept “distributed agency” was applied to analyse the thermal comfort practices in non-domestic buildings. This concept helped to illustrate everyday actions by occupants and facilities managers in relation to the organisational context. Occupants’ actions and building management practices could be affected by the organisation norms and context leading to problems and dissatisfaction with indoor thermal conditions.

This study is based on a small number of case studies and it is exploratory. Extensive monitoring data were not available. However, the research identified the thermal conditions and occupants’ satisfaction levels as background where actions to achieve thermal comfort and facilities manager’s practices took place.

The study suggests the need to examine in greater depth how the organisational goals and individual goals could be linked to support specific building performance targets.

The paper advocates for the application of multidisciplinary approaches to study the occupant dimension of building performance. It suggests the need to develop a nuanced understanding of how occupants pursue comfort as active agents who interact with the built environment.

The study has applied social practice theory to consider the influence of the organisation on thermal comfort practices in non-domestic buildings; considering the perspectives of building occupants and facilities managements within the organisational context.

Heat gain in buildings occurs due to heat transfer through the building fabric or envelope, especially the walls and roof. The purpose of this paper is to identify and recommend the suitable wall materials for better thermal performance in buildings in warm and hot climatic zones of India. As India lies between the tropic of cancer and the equator, the solar radiation from the sun falls more on the walls than the roofs of the buildings. Thus, it is imperative to protect the walls from heat gain to promote thermal comfort in naturally ventilated buildings and reduce the energy loads due to artificial cooling systems in air-conditioned buildings.

In this paper, an investigation of heat flow characteristics in steady-state and the transient state for five different uninsulated wall structures using computational fluid dynamics (CFD) software has been carried out. The climate conditions at Madurai, India have been considered for this study.

The findings of the study revealed that aerated autoclaved concrete (AAC) and hollow clay blocks (HCB) for external walls in naturally ventilated buildings in warm climatic regions could improve the building’s thermal performance index and reduce peak indoor operative temperature by about 6°C–7°C. The results of steady-state and transient state analysis were found to be in good agreement with the results of the reviewed literature.

Over the past few decades, only very few architects and builders have been successful in influencing their clients to accept alternate materials such as AAC blocks, HCB, stabilized earth blocks, adobe blocks, fly-ash bricks as an alternate to conventional bricks in an attempt of highlighting their benefits, such as; materials that are easily available, more energy-efficient, can withstand the extreme weather conditions, promote thermal comfort and cost-effective. This paper provides strong evidence that AAC and HCB blocks are the most appropriate materials for improving the thermal performance of envelope walls in regions where the outdoor temperatures are above 40°C.

This paper has made an attempt to identify the appropriate wall materials for effective thermal performance in warm and hot climates. A comparative analysis between five different wall types under the existing solar conditions has been analyzed using CFD simulation study in steady-state and transient conditions under summer conditions and the appropriate wall materials have been suggested. There has been no attempt carried out so far to analyze the thermal performance of different walls using 24 h transient approach in CFD.

The residential sector in Ireland accounted for 25 per cent of energy related CO2 emissions in 2016 through burning fossil fuels, a major contributor to climate change. In support of Ireland’s CO2 reduction targets, the existing housing stock could contribute greatly to the reduction of space-heating energy demand through retrofit. Approximately 50 per cent of Ireland’s 2m dwellings pre-date building regulations and are predominantly of cavity and solid wall construction, the performance of which has not been extensively investigated at present. Although commitment to thermal upgrade/retrofit of existing buildings may increase under future government policies, the poor characterisation of actual thermal performance of external walls may hinder the realisation of these targets. Thermal transmittance (U-values) of exterior walls represents a source of uncertainty when estimating the energy performance of dwellings. It has been noted in research that the standard calculation methodology for thermal transmittance should be improved. Implementing current U-value calculation methods may result in misguided retrofit strategies due to the considerable discrepancies between in situ measurements and calculated wall U-values as documented in the case studies carried out in this research. If the method of hygrothermal analysis were to be employed as a replacement for the current standard calculation, it could have significant implications for policy and retrofit decision making. The paper aims to discuss this issue.

This research project analysed a case study situated in Dublin, Ireland. The case studies offer an account of the in situ thermal transmittance of exterior walls and link these to hygrothermally simulated comparisons along with more traditional design U-values.

The findings of this research identify discrepancies between in situ and design U-values, using measurement, hygrothermal simulation and standard method U-value calculations. The outcomes of the research serve as an introduction to issues emanating from a larger research project in order to encourage researchers to understand and further explore the topic.

It has previously been highlighted that moisture content is linked to the increase in thermal conductivity of building materials, thus reducing the thermal effectiveness and increasing the elemental U-value. Therefore, it is vital to implement reliable prediction tools to assess potential thermal performance values. This paper presents the findings of a critical instance case study in Dublin, Ireland in which an existing west facing external wall in a semi-detached dwelling was analysed, simulated and measured to verify the elemental wall assembly and quantify thermal transmittance (U-value) incorporating the major criteria required for building performance simulation.

Understanding the thermal performance of sandcrete hollow block walls in the tropic is very essential for occupants' well-being, productivity and efficiency, due to its widespread application in buildings in the study area. Lokoja, in Nigeria, lies in the warm humid zone with its attendant's high temperatures all year round. Thus, providing an acceptable walling material that will control the high indoor air temperature becomes imperative. This paper assessed sandcrete hollow blocks as a walling material used in Lokoja, to determine the thermal performances for effective thermal comfort of the residents.

It involves the construction of a habitable model building with the commonly available sandcrete hollow blocks in the area. One unit of Cryopak iMINI Temperature and Relative Humidity Data Logger called new generation intelligent iMINI with Serial Number and Product Code MX-CI-145–0009 and MX-HE-S-16-L was installed, to record the indoor air temperature and relative humidity data at an interval of one hour, for 12 months covering dry and wet seasons. The results of the recorded data were downloaded to an excel spread sheet for assessment and analysis throughout the seasons. The values were computed using the temperature–humidity index (THI) equation, with a view to determine the indoor thermal comfort level category.

The study revealed that sandcrete hollow block walls provide thermal discomfort of the indoor environment for both seasons, with attendant adverse effects in the comfort of the occupants. The paper concludes that proper orientation of buildings, planting of trees, use of low absorbing or reflective surface materials, application of cavity walls to receive insulation materials in between the hollow spaces provided, instead of the single walling as well as providing shading device elements, can improve users' comfort and also ameliorate the heat effect on the external surface of building transferred into the interior by conduction, radiation or convection within the area and in the tropics at large. Other thermally eco-friendly wall materials available in Lokoja includes timber, stabilized laterite–cement blocks, burnt bricks and earth-mud bricks which can be used to replace sandcrete hollow block walls. These alternative wall materials are used for construction of residential and office buildings by the colonial government of Sir Fredrick Lugard in the study area.

The application of sandcrete hollow blocks as a wall material is in vogue, not minding its thermal discomfort to the users and the environment; this is due to its availability and ease of production. The acceptability of this walling material requires holistic study to unravel the best way to reduce the thermal discomfort inherent in its application.

The author succeeded in revealing the thermal performance of sandcrete hollow blocks as walling material in Lokoja, the study area. It is a first attempt at understanding the performance for human comfort in the area. This will greatly assist the resident and other researchers to improve on the application of sandcrete hollow blocks as walling material towards ensuring that maximum indoor thermal comfort is achieved.

Despite the number of quality management procedures being currently applied, construction defects in the domestic sector are acknowledged to contribute to the energy performance gap of buildings. This paper investigates the limitations and challenges to the implementation of project quality plans (PQPs) and their impact on the achievement of expected thermal performance in the UK social housing projects.

A qualitative approach, guided by grounded theory, was used in this research. This methodology provided the structure for systematic data analysis iterations, enabling cross-case analysis. An analytic induction process was designed to seek the explanation of the targeted phenomenon and required data collection until no new ideas and concepts emerged from the research iterations. This study collected data from five social housing projects through interviews, site observations and project documentation.

Multiple limitations and challenges were identified in the implementation of PQP to deliver thermal efficient social housing. Generally, there is the need for more objective quality compliance procedures based on required evidence. When investigating the root of the challenges, it was concluded that the adoption of statutory approval as the main quality compliance procedure led to the dilution of the responsibility for prevention and appraisal of defects that compromised the effectiveness of PQP devised by housing associations (HA) and contractors.

This study identifies the shortcomings of PQP in addressing quality issues with potential to undermine the thermal performance of social housing projects. The findings could be used by HA, contractors and policymakers as steppingstones to improve the energy efficiency in the domestic sector.

From the 2000s onward, construction practices of urban residential buildings in China have shown a material transformation from clay brick to aerated concrete block. Moreover, the consumption of insulating materials for buildings has been increasing due to the new requirements in building energy-saving standards. This transformation and the increased consumption of insulating materials might have a vital impact on a building’s thermal comfort and its associated energy flows. Therefore, the purpose of this paper is to investigate the indoor thermal performance of urban residential buildings built with different materials and further discuss the correlations between indoor thermal comfort and the associated energy input.

This study investigated four residential buildings selected from four residential communities located in the cold climate zone of China. The Integrated Environment Solutions program was used to evaluate the thermal comfort levels and to quantify the operational energy consumption of the case study buildings. Additionally, the University of Bath’s Inventory of Carbon and Energy database was used to estimate the embodied energy consumption and CO₂ emissions.

The study found that materials transition and increasing consumption did not necessarily improve indoor thermal comfort. However, the materials transition has significantly decreased the embodied energy consumption of urban residential buildings. Furthermore, the increased utilization of insulating materials has also decreased the heating and cooling energy consumption. Therefore, overall, the environmental impacts of urban residential buildings have been reduced significantly.

In the future, residential buildings completed in the 1990s will need regular maintenance, such as adding insulation. Residential buildings completed based on the latest energy-saving requirements should optimize their ventilation design, for example, by increasing the ventilation rate and by reducing solar heat gains in the summer.

This paper investigates the effects of the materials change on thermal comfort levels and the environmental impacts of urban residential buildings in the cold climate zone of China, as these have not been the focus of many previous studies.