Search results

The purpose of this paper is to develop the bio-composite organic coatings by adding the bio-based additives that are extracted from banana peels and henna leaves as the organic corrosion inhibitors.

Bioactive constituents with inhibition properties are extracted from banana peels and henna leaves by using ethanol to form the ethanolic extract. The inhibiting efficiency of these bioactive constituents on mild steel corrosion in 3.5% sodium hydroxide (NaCl) solution is investigated. The investigation is performed using electrochemical impedance studies for 30 days. The optical and adhesive properties of the bio-composite coating systems have also been studied.

The best protection is obtained as the loading ratio of the banana peels ethanolic extract (BPEE) and henna leaves ethanolic extract (HLEE) are 10 Wt.% and 30 Wt.%, respectively. Overall, the results obtained show that the BPEE and HLEE not only enhance the optical properties but also can serve as an effective inhibitor for corrosion without affecting the adhesiveness of the neat acrylic properties.

Banana peels and henna leaves consist of bioactive constituents that have anti-corrosion properties which could inhibit corrosion.

The purpose of this study is to reveal the usability of waste paper sludge on the production of composite materials and the printability of their surfaces were investigated.

First, composite plates were produced by using dried and milled waste sludge together with polyester resin and epoxy. Screen printing using water, solvent and UV-based inks were carried out.

It was determined that UV and solvent-based inks in both resin groups were permanently attached to the surface of composite plates produced using paper mill waste sludge, while it was found that the adhesion was not achieved sufficiently in cardboard factory waste sludge.

The unique aspect of this study is obtained the composite plates from paper mill and cardboard mill waste sludge and improved the printability of them.

Formability is an important property of automotive pre-coated metals (PCMs). The purpose of this study is to investigate the effect of long alkyl chains of polycarbonatediol to control the formability of polyester coatings.

Polyester resins with long alkyl chains were synthesized using different contents of polycarbonatediol. These resins were characterised by gel permeation chromatography (GPC), ¹H nuclear magnetic resonance (¹H NMR) and fourier transform infrared spectroscopy (FT-IR). The polyester coatings were characterised according to their viscoelastic behaviour, formability, flexibility and anti-corrosion property.

The tensile strength of PCM should be larger than 5.6 MPa of the compressive stress at a strain of 23.4 per cent to overcome the harsh condition of deep drawing. To analyse the formability, F_ε (forming coefficient based on strain) and F_U (forming coefficient based on strain energy) were calculated. When F_ε and F_U were larger than 1, the polyester coatings exhibited good formability.

Long alkyl chains of polycarbonatediol gave flexibility and good formability to the polyester coatings.

There are two conditions that lead to the good formability of PCM. One is tensile strength and the other is forming coefficients based on strain and strain energy.

Long alkyl chains of polyester were a major factor to improve flexibility and formability. Thus, to have good formability, the tensile strength of PCM should be larger than 5.6 MPa, and the forming coefficients should be larger than 1.

This paper aims to use the solvent–casting–evaporation method to prepare new bio-composites with thermoplastic poly(ether urethane) (TPU-polyether) as the polymer matrix and reinforced with natural chicken feather fibre (CFF).

To produce the bio-composites, 0 to 60 per cent·w/w of fibres in steps of 30 per cent·w/w were added to the polymer matrix. The uniformity of distribution of the keratin fibres in the polymer matrix was investigated via scanning electron microscopy, and the results suggested compatibility of the TPU-polyether matrix with the CFFs, thereby implying effective fibre–polymer interactions.

Addition of natural fibres to the polymer was found to decrease the mass loss of the composites at higher temperatures and decrease the glass transition temperature, as well as the storage and loss modulus, at lower temperatures, while increasing the remaining char ratio, storage modulus and loss modulus at higher temperatures.

The investigation confirmed that waste keratin CFF can improve the thermo-mechanical properties of composites, simply and cheaply, with potentially large environmental and economic benefits.

The purpose of this study is to understand the behavior of hybrid bio-composites under varied applications.

Fabrication methods and material characterization of various hybrid bio-composites are analyzed by studying the tensile, impact, flexural and hardness of the same. The natural fiber is a manufactured group of assembly of big or short bundles of fiber to produce one or more layers of flat sheets. The natural fiber-reinforced composite materials offer a wide range of properties that are suitable for many engineering-related fields like aerospace, automotive areas. The main characteristics of natural fiber composites are durability, low cost, low weight, high specific strength and equally good mechanical properties.

The tensile properties like tensile strength and tensile modulus of flax/hemp/sisal/Coir/Palmyra fiber-reinforced composites are majorly dependent on the chemical treatment and catalyst usage with fiber. The flexural properties of flax/hemp/sisal/coir/Palmyra are greatly dependent on fiber orientation and fiber length. Impact properties of flax/hemp/sisal/coir/Palmyra are depended on the fiber content, composition and orientation of various fibers.

This study is a review of various research work done on the natural fiber bio-composites exhibiting the factors to be considered for specific load conditions.

The purpose of this study is to develop jute-glass hybrid fibre reinforced polyester-based bio-composites using an indigenously developed pultrusion set-up and to present a detailed discussion on their mechanical characterization.

The work was carried out to observe the hybridization effect of natural and synthetic fibres in combination with hybrid fillers loading mainly on strength and other properties. The used hybrid fillers were a combination of 9 Wt.% of carbon black%, 6 Wt.% of eggshell ash powder and 6 Wt.% of coconut coir ash powder. A lab-based developed pultrusion set-up was used to develop these hybrid GJFRP composites of 1,500 mm length. The developed composites were tested for tensile strength, compressive strength and impact strength.

The maximum tensile, compressive and impact strength obtained are 88.37 MPa, 56.13 MPa and 731.91 J/m from 9 Wt.%, 9 Wt.% and 0 Wt.% of hybrid fillers loading, respectively. Breaking energy was found maximum as 7.31 J in hybrid glass-jute hybrid fibre reinforced plastic composites with no filler loading and it was observed that filler loading was decreasing the impact strength of developed hybrid composites. Shrinkage and its variations in the diameter of the finally developed cylindrical shape composites were observed after cooling and solidification. Scanning electron microscopy was used to observe the internal cracks, bonding of fibres and resin, voids, etc.

Development of hybrid filler based novel eco-friendly bio-composites and its experimental investigation on the impact strength, tensile strength and compressive strength has not been attempted yet.

Examines the fifteenth published year of the ITCRR. Runs the whole gamut of textile innovation, research and testing, some of which investigates hitherto untouched aspects. Subjects discussed include cotton fabric processing, asbestos substitutes, textile adjuncts to cardiovascular surgery, wet textile processes, hand evaluation, nanotechnology, thermoplastic composites, robotic ironing, protective clothing (agricultural and industrial), ecological aspects of fibre properties – to name but a few! There would appear to be no limit to the future potential for textile applications.

The purpose of this paper is to investigate the performance of post-disaster housing reconstruction projects, propose the conceptual living-transforming disaster relief shelter (LTFDR-shelter) approach where temporary shelter is incrementally transformed into a more permanent dwelling by using living technologies and investigate its applicability to provide sustainable post-disaster housing following natural-hazard-induced disasters.

A questionnaire survey with 120 household recipients of three Sri Lankan post-disaster housing projects was employed to explore how the post-disaster housing projects have performed against the occupants' expectations. Furthermore, the new proposed LTFDR-shelter conceptual approach's applicability to address the existing issues found in the study was investigated.

The paper evaluates and identifies the physical and technical, and socio-economic performance issues of post-disaster housing and discusses the applicability of the proposed LTFDR-shelter conceptual approach as an efficient tool to adequately improve the identified factors integrating three phases of relief, rehabilitation and reconstruction employing living technology.

Although the study's scope was limited to the occupant view of the performance of post-disaster housing in Sri Lanka, the findings and conceptual LTFDR-shelter approach could be of particular relevance to other developing countries affected by similar disasters. Further research is recommended to investigate and develop this concept in depth.

This study lays the conceptual foundation for a new theoretical approach in post-disaster housing, which encourages more interdisciplinary collaborations and empirical investigations that potentially enhance post-disaster housing performance and facilitates the application of living technology in the built environment.

The purpose of this paper is to investigate the influences of coating colours and their contents on the fundamental properties of base papers and also evaluate these results in terms of mechanical and wood-free papers.

A design research approach has been based on the application of various coating colours and analysis of mechanical and optical tests results of the coated mechanical and wood-free base papers.

This study is confirmed that the coating colours can be easily applied to the surface of the papers. The experimental data have revealed that significant improvements exist in the values of tear resistance (strength), brightness and opacity of the mechanical base papers, especially by the application of the coating colours including kaolin pigment. The results show that mechanical papers can also be used in areas with high brightness expectations by applying coating colour.

The originality of this work is based on understanding and comparing the effects of applying similar coating formulations on mechanical and wood-free base papers.

Examines the sixteenth published year of the ITCRR. Runs the whole gamut of textile innovation, research and testing, some of which investigates hitherto untouched aspects. Subjects discussed include cotton fabric processing, asbestos substitutes, textile adjuncts to cardiovascular surgery, wet textile processes, hand evaluation, nanotechnology, thermoplastic composites, robotic ironing, protective clothing (agricultural and industrial), ecological aspects of fibre properties – to name but a few! There would appear to be no limit to the future potential for textile applications.