Search results

This paper aims to develop a new 3D analytical model in cylindrical coordinates to study radial flux eddy current couplers (RFECC) while considering the magnetic edge and 3D curvature effects, and the field reaction due to the induced currents.

The analytical model is developed by combining two formulations. A magnetic scalar potential formulation in the air and the magnets regions and a current density formulation in the conductive region. The magnetic field and eddy currents expressions are obtained by solving the 3D Maxwell equations in 3D cylindrical coordinates with the variable separation method. The torque expression is derived from the field solution using the Maxwell stress tensor. In addition to 3D magnetic edge effects, the proposed model takes into account the reaction field effect due to the induced currents in the conducting part. To show the accuracy of the developed 3D analytical model, its results are compared to those from the 3D finite element simulation.

The obtained results prove the accuracy of the new developed 3D analytical model. The comparison of the 3D analytical model with the 2D simulation proves the strong magnetic edge effects impact (in the axial direction) in these devices which must be considered in the modelling. The new analytical model allows the magnetic edge effects consideration without any correction factor and also presents a good compromise between precision and computation time.

The proposed 3D analytical model presents a considerably reduced computation time compared to 3D finite element simulation which makes it efficient as an accurate design and optimization tool for radial flux eddy current devices.

A new analytical model in 3D cylindrical coordinates has been developed to find the electromagnetic torque in radial flux eddy current couplers. This model considers the magnetic edge effects, the 3D curvature effects and the field reaction (without correction factors) while improving the computation time.

The purpose of this paper is to present an applied method to design the low-speed contact between a mass and surface of a beam using an analytical solution based on the first-order shear deformation beam theory. Also, a simulation of impact process is carried out by ABAQUS finite element (FE) code.

In theoretical formulation, first strains and stresses are obtained, then kinetic and potential energies are written, and using a combination of Ritz and Lagrange methods, a set of system of motion equations in the form of mass, stiffness and force matrices is obtained. Finally, the motion equations are solved using Runge–Kutta fourth order method.

The von Mises stress contours at the impact point and contact force from the ABAQUS simulation are illustrated and it is revealed that the theoretical solution is in good agreement with the FE code. The effect of changes in projectile speed, projectile diameter and projectile mass on the results is carefully examined with particular attention to evaluate histories of the impact force and beam recess. One of the important results is that changes in projectile speed have a greater effect on the results than changes in projectile diameter, and also changes in projectile mass have the least effect.

This paper presents a combination of methods of energy, Ritz and Lagrange and also FE code to simulate the problem of sandwich beams under low velocity impact.

Detecting the orientation of cracks is a major challenge in the development of eddy current nondestructive testing probes. Eddy current-based techniques are limited in their ability to detect cracks that are not perpendicular to induced current flows. This study aims to investigate the application of the rotating electromagnetic field method to detect arbitrary orientation defects in conductive nonferrous parts. This method significantly improves the detection of cracks of any orientation.

A new rotating uniform eddy current (RUEC) probe is presented. Two exciting pairs consisting of similar square-shaped coils are arranged orthogonally at the same lifting point, thus avoiding further adjustment of the excitation system to generate a rotating electromagnetic field, eliminating any need for mechanical rotation and focusing this field with high density. A circular detection coil serving as a receiver is mounted in the middle of the excitation system.

A simulation model of the rotating electromagnetic field system is performed to determine the rules and characteristics of the electromagnetic signal distribution in the defect area. Referring to the experimental results aimed to detect artificial cracks at arbitrary angles in underwater structures using the rotating alternating current field measurement (RACFM) system in Li et al. (2016), the model proposed in this paper is validated.

CEDRAT FLUX 3D simulation results showed that the proposed probe can detect cracks with any orientation, maintaining the same sensitivity, which demonstrates its effectiveness. Furthermore, the proposed RUEC probe, associated with the exploitation procedure, allows us to provide a full characterization of the crack, namely, its length, depth and orientation in a one-pass scan, by analyzing the magnetic induction signal.

The purpose of this paper is to achieve the multi-objective optimization design of novel tubular switched reluctance motor (TSRM).

First, the structure and initial dimensions of TSRM are obtained based on design criteria and requirements. Second, the sensitivity analysis rules, process and results of TSRM are performed. Third, three optimization objectives are determined by the average electromagnetic force, smoothing coefficient and copper loss ratio. The analytic hierarchy process-entropy method-a technique for order preference by similarity to an ideal solution-grey relation analysis comprehensive evaluation algorithm is used to optimize TSRM. Finally, a prototype is manufactured, a hardware platform is built and static and dynamic experimental validations are carried out.

The sensitivity analysis reveals that parameters significantly impact the performance of TSRM. The results of multi-objective optimization show that the average electromagnetic force and smoothing coefficient after optimization are better than before, and the copper loss ratio reduces slightly. The experimental and simulated results of TSRM are consistent, which verifies the accuracy of TSRM.

In this paper, only three optimization objectives are selected in the multi-objective optimization process. To improve the performance of TSRM, the heating characteristics, such as iron loss, can be considered as the optimization objective for a more comprehensive analysis of TSRM performance.

A novel motor structure is designed, combining the advantages of the TSRM and the linear motor. The established sensitivity analysis rules are scientific and suitable for the effects of various parameters on motor performance. The proposed multi-objective optimization algorithm is a comprehensive evaluation algorithm. It considers subjective weight and objective weight and fully uses the original data and the relational degree between the optimization objectives.

In this paper, an improved multiobjective particle swarm optimization (PSO) algorithm is proposed to optimize a three-phase, 12-slot, 19-pole, yokeless axial-field flux-switching permanent magnet (YASA-AFFSPM) motor.

Based on the structural characteristics of the YASA-AFFSPM, a mathematical model is established to calculate the main size of the YASA-AFFSPM motor. The split ratio, stator axial length, sandwiching pole angle, rotor pole angle, PM arc and number of conductors per slot are selected as optimization variables. Also, the efficiency, power factor, cogging torque and average torque are considered as the optimization objectives. The objectives are optimized by combining the improved multiobjective PSO algorithm with electromagnetic calculation.

Based on the proposed algorithm, the investigated motor is optimized. The on-load efficiency, power factor and average torque of the motor performance have increased by 0.87%, 3.13% and 10.39%, respectively. Moreover, the cogging torque and slot fill factor have undergone decreases of 8.57% and 3.34%, respectively. Finally, the effectiveness of the algorithm is verified using experiment results.

So far, no comprehensive report has been observed on the optimization of the YASA-AFFSPM motor using evolutionary algorithms and the study of the effect of the motor parameters. Therefore, in this paper, the authors decided to investigate the effect of YASA-AFFSPM motor parameters and improve motor performance with the improved PSO method.

Evaluating the multiphysics performance of an electric motor can be a computationally intensive process, especially where several complex subsystems of the motor are coupled together. For example, evaluating acoustic noise requires the coupling of the electromagnetic, structural and acoustic models of the electric motor. Where skewed poles are considered in the design, the problem becomes a purely three-dimensional (3D) multiphysics problem, which could increase the computational burden astronomically. This study, therefore, aims to introduce surrogate models in the design process to reduce the computational cost associated with solving such 3D-coupled multiphysics problems.

The procedure involves using the finite element (FE) method to generate a database of several skewed rotor pole surface-mounted permanent magnet synchronous motors and their corresponding electromagnetic, structural and acoustic performances. Then, a surrogate model is fitted to the data to generate mapping functions that could be used in place of the time-consuming FE simulations.

It was established that the surrogate models showed promising results in predicting the multiphysics performance of skewed pole surface-mounted permanent magnet motors. As such, such models could be used to handle the skewing aspects, which has always been a major design challenge due to the scarcity of simulation tools with stepwise skewing capability.

The main contribution involves the use of surrogate models to replace FE simulations during the design cycle of skewed pole surface-mounted permanent magnet motors without compromising the integrity of the electromagnetic, structural, and acoustic results of the motor.

This papers aims to study lattice structures in terms of geometric variables, manufacturing variables and material-based variants and their correlation with compressive behaviour for their application in a methodology for the design and development of personalized elastic therapeutic products.

Lattice samples were designed and manufactured using extrusion-based additive manufacturing technologies. Mechanical tests were carried out on lattice samples for elasticity characterization purposes. The relationships between sample stiffness and key geometric and manufacturing variables were subsequently used in the case study on the design of a pressure cushion model for validation purposes. Differentiated areas were established according to patient’s pressure map to subsequently make a correlation between the patient’s pressure needs and lattice samples stiffness.

A substantial and wide variation in lattice compressive behaviour was found depending on the key study variables. The proposed methodology made it possible to efficiently identify and adjust the pressure of the different areas of the product to adapt them to the elastic needs of the patient. In this sense, the characterization lattice samples turned out to provide an effective and flexible response to the pressure requirements.

This study provides a generalized foundation of lattice structural design and adjustable stiffness in application of pressure cushions, which can be equally applied to other designs with similar purposes. The relevance and contribution of this work lie in the proposed methodology for the design of personalized therapeutic products based on the use of individual lattice structures that function as independent customizable cells.

The purpose of this paper is to verify results related to losses in the core of a brushless DC prototype motor, obtained using its computer FE models, by experimental tests on manufactured machines. The paper focuses on the comparison of losses in the core of a machine with a classical stator core made of an iron–silicon material (Fe–Si) and a new one made of a modern METGLAS material.

Computer models of the prototype motors were created using FEM. The designed machines were manufactured, and experimental tests were performed. To achieve high frequencies in rotating magnetic fields, motors with a stator to rotor pole ratio of 9/12 were built. Twin rotor approach was applied, as two identical rotors were built along the two geometrically identical stators made of different core materials.

Experimental studies have shown the superiority of the METGLAS material over the classical Fe–Si material. Material parameters were measured directly on the prepared cores as library data used in the simulation may be incorrect due to technological processes during core production, which was also verified. Problems related to twin rotor approach have been identified. Solution to the problem has been suggested. Necessity of 3D FEM modelling was identified.

The main source of originality is that METGLAS material used in the prototype machines was developed and manufactured by the authors themselves. Original approach to core parameter evaluation based on simplified methodology has been suggested. Another original part is a simplified methodology applied to loss measurement during no-load test.

The purpose of this paper is to predict the effect of bra pad specifications on breast deformation during jumping using a finite element (FE) method. Breast deformation is a key concern for women during exercise and can be effectively controlled with sports bras. In most studies, the deformation of breasts when wearing a sports bra is measured using motion capture devices to judge their effectiveness. However, the operation of such devices is highly complex and time-consuming. Computer-aided technology is an efficient way to simulate these experiments.

In this study, the breast model was obtained using three-dimensional (3D) scanning. Assembling models were obtained for FE analysis using reverse engineering and computer-aided design (CAD) software. The breast deformation results were obtained by completing pre-processing, solving and post-processing in the FE simulation software. To extend the application of these models, pads of different sizes and thicknesses within the bra were constructed to simulate the effect of pads on breast deformation.

The calculated root mean square errors were <1%, which indicated good agreement between the FE and experimental data in all the models. Nipple deformation was always the largest in most models. The smallest deformation occurred at the superior position of breasts in all models. In addition, larger pads were not effective in reducing breast deformation; however, thicker pads were.

The method developed in this study provides an effective way to predict breast deformation in multiple positions and is convenient for designing compression bras.

This research paper aims to investigate reinforced concrete (RC) walls' behaviour under fire and identify the thermal and mechanical factors that affect their performance.

A three-dimensional (3D) finite element (FE) model is developed to predict the response of RC walls under fire and is validated through experimental tests on RC wall specimens subjected to fire conditions. The numerical model incorporates temperature-dependent properties of the constituent materials. Moreover, the validated model was used in a parametric study to inspect the effect of the fire scenario, reinforcement concrete cover, reinforcement ratio and configuration, and wall thickness on the thermal and structural behaviour of the walls subjected to fire.

The developed 3D FE model successfully predicted the response of experimentally tested RC walls under fire conditions. Results showed that the fire resistance of the walls was highly compromised under hydrocarbon fire. In addition, the minimum wall thickness specified by EC2 may not be sufficient to achieve the desired fire resistance under considered fire scenarios.

There is limited research on the performance of RC walls exposed to fire scenarios. The study contributed to the current state-of-the-art research on the behaviour of RC walls of different concrete types exposed to fire loading, and it also identified the factors affecting the fire resistance of RC walls. This guides the consideration and optimisation of design parameters to improve RC walls performance in the event of a fire.