Search results

The purpose of this paper is the application and the improvement of a previous method based on an acrylonitrile butadiene styrene thread deposition in fused deposition modeling. To gain up to 20 per cent of mechanical strength in comparison with a classical deposition, this method suggests a smart threads deposition in the principal stresses direction.

In this work, the authors use single edge notched bend specimens with mixed mode I+II loading cases to study the influence of the thread deposition on the fracture toughness of the specimens. For this purpose, finite elements simulations have been used to evaluate the fracture toughness of the specimens through the calculation of the J integral. The study presents a method to compare the optimized and classical specimens and also to gather data and suggest a numerical model for this optimized deposition. For this reason, tensile tests are carried out to characterize the mechanical behavior of the printed samples with respect to the raster angle. Extra attention has been paid to 45 per cent samples behavior that shows a pronounced plasticity before the fracture. This interprets partially the improvement in the fracture behavior of the single edge notched bend samples.

The results show an enhancement through this optimization which leads to an increase of the maximal force in fracture up to 20 per cent and the fracture toughness of the specimens with stress intensity factors KI and KII increases about 30 per cent.

Additive manufacturing is increasingly gaining importance not only in prototyping but also in industrial production. For this reason, the characterization and the optimization of these technologies and their materials are fundamental. An adaptive deposition through a smart material based on specific mechanical behaviors would be an advance.

Epoxy resins are widely used in a variety of engineering applications, including composite wind turbine blades used in the renewable energy industry, highly complex structural components for aircraft, paints, coatings, industrial tooling, biomedical systems, adhesives, electronics and automotive. Epoxies' low fracture toughness is one of the key obstacles preventing its adoption in a wider range of applications. To address epoxy's low fracture toughness, this paper aims to examine the roles of intra-ply hybridization and nano reinforcing.

This paper investigates the role of intra-ply hybridization of glass-carbon woven fibers and adding 0.8 wt.% of multiwall carbon nanotube (MWCNT) nano reinforcement to overcome the low fracture toughness of epoxy. A bending test is used to calculate the composites elastic parameters, and a notched sample three-point bending test is used to show crack behavior in addition to using materials characterization methods to reveal the effect of the MWCNT on structure, bonding, glass transition temperature (Tg) and dispersion of MWCNT in the matrix. Furthermore, this paper suggests using the finite element method to overcome the difficulty in calculating the crack extension.

Intra-ply hybridization and MWCNT reinforcement decrease the crack extension of epoxy with time. The inclusion of high-strength carbon fiber increased the fracture toughness of glass composite. Furthermore, the existence of MWCNT in the surrounding area of the notch in epoxy composites hinders crack propagation and provides stiffness at the interface by bridging the crack and eventually enhancing its fracture toughness.

Studying the role of intra-ply hybridization of glass-carbon woven fibers and adding 0.8 wt.% of MWCNT nano reinforcement to overcome the low fracture toughness of epoxy. Additionally, this research recommends using the finite element method to overcome the challenge of computing the crack extension.

The purpose of this study was to investigate the effect of overload (bending moment with plastic deformation: Mp) on three point bending specimen at the fatigue limit of high-tensile-strength steel containing a crack in the stress concentration zone.

An artificial semi-circular slit was introduced and Mp was applied after which bending fatigue tests were carried out.

The relationship between the level of Mp and the fatigue limit (σ_w) was proportional; the fatigue limits of specimens containing 0.2- and 0.3-mm-deep slits are improved by the Mp process as much as twice the original values; the slit size that can be rendered harmless by the Mp process is a=0.05 mm in depth; and all non-propagating cracks appeared around the artificial slit.

Very few studies have been conducted on the fatigue limit of materials containing crack-like surface defects after overload in the stress concentration zone. This study elucidated the effect of Mp on the fatigue limit.

This paper aims to introduce a multiscale computational method for structural failure analysis with inheriting simulation of moving trans-scale boundary (MTB). This method is motivated from the error in domain bridging caused by cross-scale damage evolution, which is common in structural failure induced by damage accumulation.

Within the method, vulnerable regions with high stress level are described by continuum damage mechanics, while elastic structural theory is sufficient for the rest, dividing the structural model into two scale domains. The two domains are bridged to generate mixed dimensional finite element equation of the whole system. Inheriting simulation is developed to make the computation of MTB sustainable.

Numerical tests of a notched three-point bending beam and a steel frame show that this MTB method can improve efficiency and ensure accuracy while capturing the effect of material damage on deterioration of components and structure.

The proposed MTB method with inheriting simulation is an extension of multiscale simulation to structural failure analysis. Most importantly, it can deal with cross-scale damage evolution and improve computation efficiency significantly.

This study aims to systematically compare the effect of increasing fiber–matrix interface adhesion and matrix toughness in layered composite materials.

Silane ((3-glycidyloxypropyl) trimethoxysilane) was applied to strengthen the fiber–matrix interface connection in e-glass/epoxy laminated composite material. Using a cationic surfactant, 0.1% multi-walled carbon nanotubes (CNTs) were added to the matrix in two different ways, by with and without chemical functionalization using the vacuum infusion method.

In the results obtained from the three-point bending test specimens, it was determined that the synergistic effect of silane application and non-functionalized CNT in the matrix was higher in terms of flexural modulus and strength values.

The functionalization of multi-walled CNT did not give the expected results because of reasons such as viscosity increase and agglomeration in the matrix.

In this study, a simple model for normalization and prediction purposes was developed, which allows the determination of the flexural modulus and un-notched flexural strength values from one test result of the notched specimen. A systematic comparison was performed by varying each parameter in the composite material.

Gives a bibliographical review of the finite element methods (FEMs) applied for the linear and nonlinear, static and dynamic analyses of basic structural elements from the theoretical as well as practical points of view. The range of applications of FEMs in this area is wide and cannot be presented in a single paper; therefore aims to give the reader an encyclopaedic view on the subject. The bibliography at the end of the paper contains 2,025 references to papers, conference proceedings and theses/dissertations dealing with the analysis of beams, columns, rods, bars, cables, discs, blades, shafts, membranes, plates and shells that were published in 1992‐1995.

Macro synthetic steel fibers were incorporated into the concrete material as a toughening agent to improve the corrosion and cracking resistances of concrete in a sulfate-containing service environment.

To study the basic mechanical properties of this system, an accelerated concrete degradation test was designed to evaluate the influence of the sulfate ions on the concrete. A three-point bending test was carried out in the laboratory to evaluate the fracture toughness. The thickness of the damaged concrete layer and changes of microstructure of the degraded concrete were monitored by using ultrasound, scanning electron microscopy and X-ray diffraction detection methods.

The results showed that compared to the performance of ordinary concrete, in an exposure environment containing sulfate ions, the structure compactness of macro synthetic steel fiber concrete was improved, degradation resistance to the sulfate solution was enhanced and the fracture resistance performance was improved significantly.

The thickness of the degradation layer on the macro synthetic steel fiber concrete was less than a half of that of ordinary concrete in the sulfate environment, and was generally unchanged with increase in the sulfate concentration. Through micro-structural analysis, it was confirmed that macro synthetic steel fiber improved the compactness of the concrete structure, inhibiting access of sulfate ions to the interior of the concrete and thereby reducing the degree of sulfate degradation to the concrete.

This study aims to predict the fracture properties of geopolymer concrete, which is necessary for studying failure behaviour of concrete.

Geopolymers are new alternative binders for cement in which polymerization gives strength to concrete rather than through hydration. Geopolymer concrete was developed from industrial byproducts such as GGBS and dolomite. Present study estimates the fracture energy of GGBS geopolymer concrete using three point bending test (RILEM TC50-FMC) with different percentages of dolomite and compare with cement concrete having same strength.

The fracture properties such as peak load, critical stress intensity factor, fracture energy and characteristic length are found to be higher for GGBS-dolomite geopolymer concrete, when their proportion becomes 70:30.

To the best of the authors’ knowledge, this is an original experimental work.

Simple but also accurate models are needed to predict the failure response of concrete structures. Simplicity involves modelling assumptions while accuracy involves objectivity of both the experimentally identified model parameters and the numerica results. For concrete‐like heterogeneous and brittle materials, the modelling assumptions idealizing the material as a homogeneous continuum with classical linear or non‐linear behaviour, leads to some problems at the identification stage, namely the size effect phenomena. A continuum damage model, representing the non‐linear behaviour due to microcracking, is proposed here for predictive computations of structural responses. A Weibull based theory is used to determine, in a statistical sense, the value of the initial damage threshold. The essential influence of material heterogeneity on the damage evolution, is accounted for with a bi‐scale approach which is based on the idea of the non‐local continuum with local strain. It has already established that the non‐local approaches yield realistic failure predictions and the numerical results are convergent for subsequent mesh refinements. The applications presented here show the ability of the approach to predict the failure response of concrete structures without being obscured by size effect problems.

Mechanical anisotropy associated with material extrusion additive manufacturing (AM) complicates the design of complex structures. This study aims to focus on investigating the effects of design choices offered by material extrusion AM – namely, the choice of infill pattern – on the structural performance and optimality of a given optimized topology. Elucidation of these effects provides evidence that using design tools that incorporate anisotropic behavior is necessary for designing truly optimal structures for manufacturing via AM.

A benchmark topology optimization (TO) problem was solved for compliance minimization of a thick beam in three-point bending and the resulting geometry was printed using fused filament fabrication. The optimized geometry was printed using a variety of infill patterns and the strength, stiffness and failure behavior were analyzed and compared. The bending tests were accompanied by corresponding elastic finite element analyzes (FEA) in ABAQUS. The FEA used the material properties obtained during tensile and shear testing to define orthotropic composite plies and simulate individual printed layers in the physical specimens.

Experiments showed that stiffness varied by as much as 22% and failure load varied by as much as 426% between structures printed with different infill patterns. The observed failure modes were also highly dependent on infill patterns with failure propagating along with printed interfaces for all infill patterns that were consistent between layers. Elastic FEA using orthotropic composite plies was found to accurately predict the stiffness of printed structures, but a simple maximum stress failure criterion was not sufficient to predict strength. Despite this, FE stress contours proved beneficial in identifying the locations of failure in printed structures.

This study quantifies the effects of infill patterns in printed structures using a classic TO geometry. The results presented to establish a benchmark that can be used to guide the development of emerging manufacturing-oriented TO protocols that incorporate directionally-dependent, process-specific material properties.