Search results

The purpose of this paper is to clarify the influence of low earth orbit space environment on the wear mechanism of TC4 alloy material and crank rocker mechanism.

In this study, friction experiments were carried out on TC4 alloy friction discs and crank rocker mechanisms, both before and after exposure to atomic oxygen and proton irradiation. Nanoindentation, grazing incidence X-ray diffraction (GIXRD), and X-ray photoelectron spectroscopy were employed to systematically characterize alterations in mechanical properties, surface phase, and chemical composition.

The results show that the wear mechanism of TC4 alloy friction disc is mainly adhesive wear in vacuum environment, while the wear mechanism of crank rocker mechanism includes not only adhesive wear but also abrasive wear. Atomic oxygen exposure leads to the formation of more oxides on the surface of TC4 alloy, which form abrasive particles during the friction process. Proton irradiation will lead to a decrease in fatigue performance and an increase in hardness on the surface of TC4 alloy, thus causing fatigue wear on the surface of TC4 alloy, and more furrows appear on the crank rocker mechanism after proton irradiation. In the three environments, the characteristics of abrasive wear of the crank rocker mechanism are more obvious than those of the TC4 alloy friction disc.

These results highlight the importance of understanding the subtle effects of atomic oxygen and proton irradiation on the wear behavior of TC4 alloy and provide some insights for optimizing its performance in space applications.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-02-2024-0051/

The purpose of this paper is to assess the hydrogen embrittlement sensitivity of carbon gradient heterostructure materials and to verify the reliability of the scratch method.

The surface-modified layer of 18CrNiMo7-6 alloy steel was delaminated to study its hydrogen embrittlement characteristics via hydrogen permeation, electrochemical hydrogen charging and scratch experiments.

The results showed that the diffusion coefficients of hydrogen in the surface and matrix layers are 3.28 × 10⁻⁷ and 16.67 × 10⁻⁷ cm²/s, respectively. The diffusible-hydrogen concentration of the material increases with increasing hydrogen-charging current density. For a given hydrogen-charging current density, the diffusible-hydrogen concentration gradually decreases with increasing depth in the surface-modified layer. Fracture toughness decreases with increasing diffusible-hydrogen concentration, so the susceptibility to hydrogen embrittlement decreases with increasing depth in the surface-modified layer.

The reliability of the scratch method in evaluating the fracture toughness of the surface-modified layer material is verified. An empirical formula is given for fracture toughness as a function of diffused-hydrogen concentration.

This paper aims to focus on the synthesis of the macrocyclic complexes (Cu and Zn) and their applications as anticorrosive materials in epoxy paint formulation for surface coating application.

A selected macrocyclic Cu(II) and Zn(II) complexes were prepared via template synthesis and characterized using Fourier transform infrared, thermal gravimetric analysis, scanning electron microscope, flexibility, hardness and adhesion of coating films prepared using epoxy paint.

The corrosion resistance of the epoxy-painted films was improved due to the incorporation of the Zn and Cu complexes into the formulation.

It was found that the metal complex-based formulation with Cu(II) and Zn(II) had outperformed the sample blank.

This paper aims to investigate the effect of chemical nickel plating and mechanical alloying on the mechanical and tribological properties of FeS/iron-based self-lubricating materials as well as the wear mechanism of the materials.

Surface modification of FeS powder was carried out by chemical nickel plating method and mechanical alloying of mixed powder by ball milling. The mechanical properties of the material were tested by tribological testing by M-200 ring block type friction and wear tester. Optical microscope was used to observe the surface morphology of the material and the transfer film on the surface of the mate parts, and scanning electron microscope and EDS were used to characterize the wear surface.

Mechanical alloying ball milling was carried out so that the lubricating particles in the matrix are uniformly dispersed; nickel-plated layer enhances the interfacial bonding of FeS and the matrix, and the combination of the two improves the mechanical properties of the material, and at the same time the friction side of the surface of the lubrication of FeS lubricant transfer film formed is denser and more intact, and the friction coefficient of friction side and the wear rate of the material have been greatly reduced.

This work aims to improve the mechanical and tribological properties of FeS/iron-based self-lubricating materials and to provide a reference for the preparation of materials with excellent overall properties.

This study aims to explore the synthesis, characteristics and utilization of polymer composites integrated with cutting-edge pigments.

The incorporation of advanced pigments introduces functionalities such as enhanced mechanical strength, thermal stability, ultraviolet resistance and color stability, thus extending the range of applications in diverse fields including automotive, aerospace, electronics and construction.

This review discusses the mechanisms underlying the property enhancements achieved through the incorporation of advanced pigments and highlights recent developments in the field.

Polymer composites incorporating advanced pigments have garnered significant attention in recent years because of their potential to enhance various material properties and broaden their applications. This paper explores the fabrication methods of polymer composites reinforced with organic/inorganic advanced pigments in brief along with their characteristics and applications.

This study aims to address the limited understanding of the complex correlations among strut size, structural orientation and process parameters in selective laser melting (SLM)-fabricated lattice structures. By investigating the effects of crucial process parameters, strut diameter and angle on the microstructure and mechanical performance of AlSi10Mg struts, the research seeks to enhance the surface morphologies, microstructures and mechanical properties of AM lattice structures, enabling their application in various engineering fields, including medical science and space technologies.

This comprehensive study investigates SLM-fabricated AlSi10Mg strut structures, examining the effects of process parameters, strut diameter and angle on densification behavior and microstructural characteristics. By analyzing microstructure, geometrical properties, melt pool morphology and mechanical properties using optical microscopy, scanning electron microscope, energy dispersive X-ray spectroscopy and microhardness tests, the research addresses existing gaps in knowledge on fine lattice strut elements and their impact on surface morphology and microstructure.

The study revealed that laser energy, power density and strut inclination angle significantly impact the microstructure, geometrical properties and mechanical performance of SLM-produced AlSi10Mg struts. Findings insight enable the optimization of SLM process parameters to produce lattice structures with enhanced surface morphologies, microstructures and mechanical properties, paving the way for applications in medical science and space technologies.

This study uniquely investigates the effects of processing parameters, strut diameter and inclination angle on SLM-fabricated AlSi10Mg struts, focusing on fine lattice strut elements with diameters as small as 200 µm. Unlike existing literature, it delves into the complex correlations among strut size, structural orientation and process parameters to understand their impact on microstructure, geometrical imperfections and mechanical properties. The study provides novel insights that contribute to the optimization of SLM process parameters, moving beyond the typically recommended guidelines from powder or machine suppliers.

This study aims to evaluate in situ oxidative polymerization of aniline (Ani) as a post-processing method to promote extrusion-based 3D printed parts, made from insulating polymers, to components with functional properties, including electrical conductivity and chemical sensitivity.

Extrusion-based 3D printed parts of polyethylene terephthalate modified with glycol (PETG) and polypropylene (PP) were coated in an aqueous acid solution via in situ oxidative polymerization of Ani. First, the feedstocks were characterized. Densely printed samples were then used to assess the adhesion of polyaniline (PAni) and electrical conductivity on printed parts. The best feedstock candidate for PAni coating was selected for further analysis. Last, a Taguchi methodology was used to evaluate the influence of printing parameters on the coating of porous samples. Analysis of variance and Tukey post hoc test were used to identify the best levels for each parameter.

Colorimetry measurements showed significant color shifts in PP samples and no shifts in PETG samples upon pullout testing. The incorporation of PAni content and electrical conductivity were, respectively, 41% and 571% higher for PETG in comparison to PP. Upon coating, the surface energy of both materials decreased. Additionally, the dynamic mechanical analysis test showed minimal influence of PAni over the dynamic mechanical properties of PETG. The parametric study indicated that only layer thickness and infill pattern had a significant influence on PAni incorporation and electrical conductivity of coated porous samples.

Current literature reports difficulties in incorporating PAni without affecting dimensional precision and feedstock stability. In situ, oxidative polymerization of Ani could overcome these limitations. However, its use as a functional post-processing of extrusion-based printed parts is a novelty.

The purpose of this study is therefore to detail an additive manufacturing process for printing TiD parts for implant applications. Titanium–diamond (TiD) is a new composite that provides biocompatible three-dimensional multimaterial structures. Thus, the authors report a powder-deposition and print optimization strategy to overcome the dual-functionality gap by printing bulk TiD parts. However, despite favorable customization outcomes, relatively few additive manufacturing (AM) feedstock powders offer the biocompatibility required for medical implant and device technologies.

AM offers a platform to fabricate customized patient-specific parts. Developing feedstock that can be 3D printed into specific 3D structures while providing a favorable interface with the human tissue remains a challenge. Using laser metal deposition, feedstock powder comprising diamond and titanium was co-printed into TiD parts for mechanical testing to determine optimal manufacturing parameters.

TiD parts were fabricated comprising 30% and 50% diamond. The composite powder had a Hausner ratio of 1.13 and 1.21 for 30% and 50% TiD, respectively. The flow analysis (Carney flow) for TiD 30% and 50% was 7.53 and 5.15 g/s. The authors report that the printing-specific conditions significantly affect the integrity of the printed part and thus provide the optimal manufacturing parameters for structural integrity as determined by micro-computed tomography, nanoindentation and biocompatibility of TiD parts. The hardness, ultimate tensile strength and yield strength for TiD are 4–6 GPa (depending on build position), 426 MPa and 375 MPa, respectively. Furthermore, the authors show that increasing diamond composition to 30% results in higher osteoblast viability and lower bacteria count than titanium.

In this study, the authors provide a clear strategy to manufacture TiD parts with high integrity, performance and biocompatibility, expanding the material feedstock library and paving the way to customized diamond implants. Diamond is showing strong potential as a biomedical material; however, upscale is limited by conventional techniques. By optimizing AM as the avenue to make complex shapes, the authors open up the possibility of patient-specific diamond implant solutions.

This paper aims to report the effect of titanium oxide (TiO₂) particles on the physical, mechanical, tribological and water resistance properties of 5% NaOH-treated bamboo fiber–reinforced composites.

In this research, the epoxy/bamboo/TiO₂ hybrid composite filled with 0–8 Wt.% TiO₂ particles has been fabricated using simple hand layup techniques, and testing of the developed composite was done in accordance with the American Society for Testing and Materials (ASTM) standard.

The results of this study indicate that the addition of TiO₂ particles improved the mechanical properties of the developed epoxy/bamboo composites. Tensile properties were found to be maximum for 6 Wt.%, and impact strength was found to be maximum for 8 Wt.% TiO₂ particles-filled composite. The highest flexural properties were found at a lower TiO₂ fraction of 2 Wt.%. Adding TiO₂ filler helped to reduce the water absorption rate. The studies related to the wear and friction behavior of the composite under dry and abrasive wear conditions reveal that TiO₂ filler was beneficial in improving the wear performance of the composite.

This research paper attempts to include both TiO₂ filler and bamboo fibers to develop a novel composite material. TiO₂ micro and nanoparticles are promising filler materials; it helps to enhance the mechanical and tribological properties of the epoxy composites and in literature, there is not much work reported, where TiO₂ is used as a filler material with bamboo fiber–reinforced epoxy composites.

This paper aims to systematically investigate the effect of laser remelting on the surface morphology and mechanical properties of laser deposition manufactured thin-walled Ti-6Al-4V alloy.

Thin-walled Ti-6Al-4V samples were prepared by laser deposition manufacturing (LDM) method and subsequently surface-treated by laser remelting in a controlled environment. By experiments, the surface qualities and mechanical properties of LDM Ti-6Al-4V alloy before and after laser remelting were investigated.

After laser remelting, the surface roughness of LDM Ti-6Al-4V alloy decreases from 15.316 to 1.813 µm, hard and brittle martensite presents in the microstructure of the remelted layer, and the microhardness of the laser remelted layer increases by 11.39%. Compared with the machined LDM specimen, the strength of the specimen including the remelted layer improves by about 5%, while the elongation and fatigue life decrease by about 72.17% and 64.60%, respectively.

The results establish foundational data for the application of laser remelting to LDM thin-walled Ti-6Al-4V parts, and may provide an opportunity for laser remelting to process the nonfitting surfaces of LDM parts.