Search results

As the crucial support component of the propeller power system, the reliability of the operation of submersible pumps is influenced by the lubrication performance of water-lubricated thrust bearings. When the water-lubricated thrust bearings are under start-stop or heavy load conditions, the effect of surface morphology is crucial as the mixed lubrication regime is encountered. This paper aims to develop one mixed lubrication model for the water-lubricated thrust bearings to predict the effects of surface skewness, kurtosis and roughness orientation on the loading carrying capacity and tribological behavior.

This paper developed one improved mixed lubrication model specifically for the water-lubricated thrust bearing system. In this model, the hydrodynamic model was improved by using the height of the rough surface and its probability density function, combined with the average flow model. The asperity contact model was improved by using the equation for the Pearson system of frequency curves to characterize the non-Gaussian aspect of surface roughness distribution.

According to the results, negative skewness, large kurtosis and lateral surface pattern can improve the tribological performance of water-lubricated thrust bearings. Optimizing the surface morphology is a reasonable design method that can improve the performance of water-lubricated thrust bearings.

In this paper, one mixed lubrication model specifically for the water-lubricated thrust bearing with the effect of surface roughness into consideration was developed. Based on the developed model, the effect of surface morphology on tribological behavior can be evaluated.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-08-2023-0247/

This paper aims to systematically investigate the effect of laser remelting on the surface morphology and mechanical properties of laser deposition manufactured thin-walled Ti-6Al-4V alloy.

Thin-walled Ti-6Al-4V samples were prepared by laser deposition manufacturing (LDM) method and subsequently surface-treated by laser remelting in a controlled environment. By experiments, the surface qualities and mechanical properties of LDM Ti-6Al-4V alloy before and after laser remelting were investigated.

After laser remelting, the surface roughness of LDM Ti-6Al-4V alloy decreases from 15.316 to 1.813 µm, hard and brittle martensite presents in the microstructure of the remelted layer, and the microhardness of the laser remelted layer increases by 11.39%. Compared with the machined LDM specimen, the strength of the specimen including the remelted layer improves by about 5%, while the elongation and fatigue life decrease by about 72.17% and 64.60%, respectively.

The results establish foundational data for the application of laser remelting to LDM thin-walled Ti-6Al-4V parts, and may provide an opportunity for laser remelting to process the nonfitting surfaces of LDM parts.

This paper aims to compare the surface roughness and hardness of three commercially available self-curing acrylic resins for dental use, under different polymerization conditions.

A comparative in vitro study was conducted using a convenience sample of 12 × 5 × 2 mm blocks with n = 40 for each material (Nic Tone, Arias Plus and Orthocryl®), with subgroups according to the polymerization method: conventional (C) and polymerization under ambient conditions (A). The surface roughness of the materials was measured using a profilometer; hardness was measured with a portable hardness tester. Additionally, surface morphology as well as particles size and morphology were evaluated with scanning electron microscopy.

There were significant differences in roughness and hardness values between the three self-curing acrylic resins (p < 0.05), as well as within each self-curing acrylic resin according to the polymerization method used (p < 0.05). The samples polymerized with the conventional method presented lower surface roughness and hardness values.

This study provides scientific evidence of values not provided by manufacturers in relation to the surface roughness and hardness of these materials, and all of them met the ideal minimum values of surface roughness, regardless of the polymerization technique used.

Surface quality and porosity significantly influence the structural and functional properties of the final product. This study aims to establish and explain the underlying relationships among processing parameters, top surface roughness and porosity level in additively manufactured 316L stainless steel.

A systematic variation of printing process parameters was conducted to print cubic samples based on laser power, speed and their combinations of energy density. Melt pool morphologies and dimensions, surface roughness quantified by arithmetic mean height (Sa) and porosity levels were characterized via optical confocal microscopy.

The study reveals that the laser power required to achieve optimal top surface quality increases with the volumetric energy density (VED) levels. A smooth top surface (Sa < 15 µm) or a rough surface with humps at high VEDs (VED > 133.3 J/mm³) can serve as indicators for fully dense bulk samples, while rough top surfaces resulting from melt pool discontinuity correlate with high porosity levels. Under insufficient VED, melt pool discontinuity dominates the top surface. At high VEDs, surface quality improves with increased power as mitigation of melt pool discontinuity, followed by the deterioration with hump formation.

This study reveals and summarizes the formation mechanism of dominant features on top surface features and offers a potential method to predict the porosity by observing the top surface features with consideration of processing conditions.

This paper aims to study the influence of microparticles on the surface cavitation behavior of 2Cr3WMoV steel; microparticle suspensions of different concentration, particle size, material and shape were prepared based on ultrasonic vibration cavitation experimental device.

2Cr3WMoV steel was taken as the research object for ultrasonic cavitation experiment. The morphology, quantity and distribution of cavitation pits were observed and analyzed by metallographic microscope and scanning electron microscope.

The study findings showed that the surface cavitation process produced pinhole cavitation pits on the surface of 2Cr3WMoV steel. High temperature in the process led to oxidation and carbon precipitation on the material surface, resulting in the “rainbow ring” cavitation morphology. Both the concentration and size of microparticles affected the number of pits on the material surface. When the concentration of microparticles was 1 g/L, the number of pits reached the maximum, and when the size of microparticles was 20 µm, the number of pits reached the minimum. The microparticles of Fe3O4, Al2O3, SiC and SiO2 all increased the number of pits on the surface of 2Cr3WMoV steel. In addition, the distribution of pits of spherical microparticles was more concentrated than that of irregularly shaped microparticles in turbidity.

Most of the current studies have not systematically focused on the effect of each factor of microparticles on the cavitation behavior when they act separately, and the results of the studies are more scattered and varied. At the same time, it has not been found to carry out the study of microparticle cavitation with 2Cr3WMoV steel as the research material, and there is a lack of relevant cavitation morphology and experimental data.

Micro-texture is processed on the surface to reduce the friction of the contact surface, and its application is more and more extensive. The purpose of this paper is to create a texture function model to study the influence of surface parameters on the accuracy of the simulated surface so that it can more accurately reflect the characteristics of the real micro-textured surface.

The microstructure function model of rough surfaces is established based on fractal geometry and polar coordinate theory. The offset angle θ is introduced into the fractal geometry function to make the surface asperity normal perpendicular to the tangent of the surface. The 2D and 3D contour surfaces of the surface groove texture are analyzed by MATLAB simulation. The effects of fractal parameters (D and G) and texture parameter h on the curvature of the surface micro-texture model were studied.

This paper more accurately characterizes the textured 3D curved surface, especially the surface curvature. The scale coefficient G significantly affects curvature, and the influence of fractal dimension D and texture parameters on curvature can be ignored.

The micro-texture model of the rough surface was successfully established, and the range of fractal parameters was determined. It provides a new method for the study of surface micro-texture tribology.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-09-2023-0298/

The purpose of this paper is to investigate the effect of laser peening (LP) on mechanical and wear properties of 304 stainless steel sheet.

Three-dimensional morphology, micro-hardness and micro-structure of shocked samples were tested. The wear amount, wear track morphology and wear mechanism were also characterized under dry sliding wear using Al₂O₃ ceramics ball.

The LP treatment generates deformation twins that contribute to the grain refinement and hardness increase. The wear test displays that the wear mechanism of samples is mainly abrasive wear and oxidation wear at 10 N load. While at 30 N, the delamination and adhesion areas of treated sample are reduced visibly compared to untreated ones.

This study specifically investigates the mechanical and wear properties of 304 stainless steel after the direct action of LP on its surface, which shows an effective improvement on the wear resistance. For example, the wear loss of processed sample is reduced by 19% at 30 N, the friction coefficient decreases from 0.4714 to 0.4308 and the groove depth is reduced from 78.1 to 74.4 µm under same condition.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-01-2024-0007/

The purpose of this paper is to determine the ultra-high cycle fatigue behavior and ultra-slow crack propagation behavior of selective laser melting (SLM) AlSi7Mg alloy under as-built conditions.

Constant amplitude and two-step variable amplitude fatigue tests were carried out using ultrasonic fatigue equipment. The fracture surface of the failure specimen was quantitatively analyzed by scanning electron microscope (SEM).

The results show that the competition of surface and interior crack initiation modes leads to a duplex S–N curve. Both manufacturing defects (such as the lack of fusion) and inclusions can act as initially fatal fatigue microcracks, and the fatigue sensitivity level decreases with the location, size and type of the maximum defects.

The research results play a certain role in understanding the ultra-high cycle fatigue behavior of additive manufacturing aluminum alloys. It can provide reference for improving the process parameters of SLM technology.

This paper aims to characterize the surface film formed on Alloys 800 and 690 in chloride and thiosulfate-containing solution at 300°C.

Alloy 800 and 690 were immersed in chloride and thiosulfate-containing solution at 300°C up to five days, and then the surface film was analyzed by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM) and energy dispersive X-ray spectrometers (EDX).

Through static immersion experiments in a high-temperature and high-pressure water environment, the alloy samples covered by surface film after five days of immersion were obtained. The morphology of the surface film was characterized at both horizontal and cross-sectional scales using SEM and focused ion beam-TEM techniques. It was observed that due to the influence of the quartz lining, the surface film primarily exhibited a bilayered structure. The first layer contained a significant amount of SiO₂, with a higher content of metal hydroxides compared to metal oxides. The second layer was predominantly composed of Fe, Ni and Cr, with a higher content of metal oxides compared to metal hydroxides.

The results showed that the materials of the lining of the autoclave could significantly influence the film composition of the tested material, which should be paid attention when analyzing the corrosion mechanism at high temperature.

The purpose of this paper was to investigate how variations in the geometry of silicon chips and the presence of surface defects affect their static bending properties. By comparing the bending radius and strength across differently sized and treated chips, the study sought to understand the underlying mechanics that contribute to the flexibility of silicon-based electronic devices. This understanding is crucial for the development of advanced, robust and adaptable electronic systems that can withstand the rigors of manufacturing and everyday use.

This study explores the impact of silicon chip geometry and surface defects on flexibility through a multifaceted experimental approach. The methodology included preparing silicon chips of three distinct dimensions and subjecting them to thinning processes to achieve a uniform thickness verified via scanning electron microscopy (SEM). Finite element method (FEM) simulations and a series of four-point bending tests were used to analyze the bending flexibility theoretically and experimentally. The approach was comprehensive, examining both the intrinsic geometric factors and the extrinsic influence of surface defects induced by manufacturing processes.

The findings revealed a significant deviation between the theoretical predictions from FEM simulations and the experimental outcomes from the four-point bending tests. Rectangular-shaped chips demonstrated superior flexibility, with smaller dimensions leading to an increased bending strength. Surface defects, identified as critical factors affecting flexibility, were analyzed through SEM and atomic force microscopy, showing that etching processes could reduce defect density and enhance flexibility. Notably, the study concluded that surface defects have a more pronounced impact on silicon chip flexibility than geometric factors, challenging initial assumptions and highlighting the need for defect minimization in chip manufacturing.

This research contributes valuable insights into the design and fabrication of flexible electronic devices, emphasizing the significant role of surface defects over geometric considerations in determining silicon chip flexibility. The originality of the work lies in its holistic approach to dissecting the factors influencing silicon chip flexibility, combining theoretical simulations with practical bending tests and surface defect analysis. The findings underscore the importance of optimizing manufacturing processes to reduce surface defects, thereby paving the way for the creation of more durable and flexible electronic devices for future technologies.