Search results

The purpose of the study is to design the compensation network of a dynamic wireless power transfer system, considering the movement of the receiving coil along an electrified track with a large number of inductors buried on the road.

A finite element model has been developed to calculate the self-inductances of transmitting and receiving coils as well as the mutual inductances between the receiving coil and the transmitting ones in the nearby and for various relative positions. The calculated lumped parameters, self-inductances and mutual inductances depending on the relative positions between the coils, have been considered to design the compensation network of the active coils, which is composed of three capacitive or inductive reactances connected in the T form. The optimal values of the six reactances, three for the transmitting coils and three for the receiving one, have been calculated by resorting to the Genetic Algorithm NSGA-II.

In this paper, the results obtained by means of the optimizations have broadly discussed. The optimal values of the reactances of the compensation networks show a clear trend in the receiving part of the circuit. On the other hand, the problem seems very sensitive to the values of the reactances in the transmitting circuit.

Dynamic wireless power transfer system is one of the newest ways of recharging electric vehicles. Hence, the design of compensation networks for this kind of systems is a new topic, and there is the need to investigate possible solutions to obtain a good performance of the recharging system.

Microribbon with meander type based on giant magnetoimpedance (GMI) effect has become a research hot spot due to their higher sensitivity and spatial resolution. The purpose of this paper is to further optimize the line spacing to improve the performance of meanders for sensor application.

The model of GMI effect of microribbon with meander type is established. The effect of line spacing (Ls) on GMI behavior in meanders is analyzed systematically.

Comparison of theory and experiment indicates that decreasing the line spacing increases the negative mutual inductance and a consequent increase in the GMI effect. The maximum value of the GMI ratio increases from 69% to 91.8% (simulation results) and 16.9% to 51.4% (experimental results) when the line spacing is reduced from 400 to 50 µm. The contribution of line spacing versus line width to the GMI ratio of microribbon with meander type was contrasted. This behavior of the GMI ratio is dominated by the overall negative contribution of the mutual inductance.

This paper explores the effect of line spacing on the GMI ratio of meander type by comparing the simulation results with the experimental results. The superior line spacing is found in the identical sensing area. The findings will contribute to the design of high-performance micropatterned ribbon with meander-type GMI sensors and the establishment of a ribbon-based magnetic-sensitive biosensing system.

This paper aims to describe a modelling and solving methodology of a (static converter–electric motor–control) system for its sizing by optimization, considering the dynamic thermal heating of the machine.

The electrical drive sizing model is composed of two simulators (electrical and thermal) that are co-simulated with a master−slave relationship for the time step management. The computation is stopped according to simulation criteria.

This paper details a methodology to represent and size an electrical drive using a multiphysics and multidynamics approach. The thermal simulator is the master and calls the electrical system simulator at a fixed exchange time step. The two simulators use a dedicated dynamic time solver with adaptive time step and event management. The simulation automatically stops on pre-established criteria, avoiding useless simulations.

This paper aims to present a generic methodology for the sizing by optimization of electrical drives with a multiphysics approach, so the precision and computation time highly depend on the modelling method of each components. A genetic multiobjective optimization algorithm is used.

The methodology can be applied to size electrical drives operating in a thermally limited zone. The power electronics converter and electrical machine can be easily adapted by modifying their sub-model, without impacting the global model and simulation principle.

The approach enables to compute a maximum operating duration before reaching thermal limits and to use it as an optimization constraint. These system considerations allow to over constrain the electrical machine, enabling to size a smaller machine while guaranteeing the same output performances.

Static inverters are very important for the emergency energy distribution system of aircraft and similar machines. At the same time, the electrical energy produced at high frequency for electrical devices is used to reduce the weight of the cables in the aircraft and spacecraft because of the skin effect. In the high-frequency system, a thinner cable cross-section is used, and a great weight reduction occurs in the aircraft. So, fuel economy, less and late wear of the materials (landing gear, etc.) can be obtained with decreasing weight. This paper aims to present the development of a functional multilevel inverter (FMLI) with fractional sinus pulse width modulation (FSPWM) and a reduced number of switches to provide high-frequency and quality electrical energy conversion.

After the production of FSPWM for FMLI with a reduced component, which, to the best of the authors’ knowledge, is presented for the first time in this study, is explained step by step, and eight operating states are given according to different FSPWMs operating the circuit. The designed inverter and modulation technique are compared by testing the conventional modular multilevel inverter on different loads.

According to application results, it is seen that there is a 50% reduction in cross-section from 100 Hz to 400 Hz with the skin effect. At 1000 Hz, there is a 90% cross-section reduction. The decrease can be in cable weights that may occur in aircraft from 10 kg to 100 kg according to different frequencies. It causes less harmonic distortion than conventional converters. This supports the safer operation of the system. Compared to the traditional system, the proposed system provides more amplitude in converting the source to alternating voltage and increases the efficiency.

FSPWM is developed for multilevel inverters with reduced components at the high frequency and cascaded switching studies in the power electronics of aircraft.

Although the proposed system has less current and power loss as mentioned in the previous sections, it contains fewer power elements than conventional inverters that are equivalent for different hardware levels. This not only reduces the cost of the system but also provides ease of maintenance. To reduce the cable load in aircraft and create more efficient working conditions, 400 Hz alternative voltage is used. The proposed system causes less losses and lower harmonic distortions than traditional systems. This will reduce possible malfunctions and contribute to aircraft reliability for passengers and cargo. As technology develops, it is revealed that the proposed inverter system will be more efficient than traditional inverters when devices operating at frequencies higher than 400 Hz are used. With the proposed inverter, safer operation will be ensured, while there will be less energy loss, less fuel consumption and less carbon emissions to the environment.

The proposed inverter structure shows that it can provide energy transmission for electrical devices in space and aircraft by using the skin effect. It also contains less power elements than the traditional inverters, which are equivalent for different levels of hardware.

To simplify the circuit design and control complexity of the magnetic coupling resonant wireless charging system, the radio energy transmission constant current and constant voltage charging is realized.

The purpose of this study is to simplify the circuit design and control complexity of the magnetic coupling resonance wireless charging system, in order to achieve constant current and constant voltage charging for wireless energy transmission. First, the principle of LCC/S-S compensation structure is analyzed, and the equivalent mathematical model is established; then, the system characteristics under constant current and constant voltage mode are analyzed, and the design method of system parameters is given; finally, a simulation and experimental system is built to verify the correctness and feasibility of the theoretical analysis.

The results show that the proposed hybrid topology can achieve a constant current output of 2 A and a constant voltage output of 30 V under variable load conditions, and effectively suppress the current distortion problem under light load conditions. The waveform distortion rate of the inverter current is reduced from 33.97% to 10.45%.

By changing the high-order impedance characteristics of the compensation structure, the distortion of the current waveform under light load is suppressed, and the overall stability and efficiency of the system are improved.

This paper aims to optimize passive damper system (PDS) design by configuring its parameters to improve its performance and behavior in permanent magnet synchronous machines (PMSM).

First, the principle and effectiveness of the PDS are recalled. Second, the impact of different PDS parameters on its operation is analyzed. Third, a multi-objective optimization is proposed to explore a compromise design of PDS. Finally, the transient finite element method simulation is performed to validate the optimized design, which can ensure an excellent noise reduction effect and weaker negative impacts.

A suitable capacitance value in PDS is a key to realizing the damping effect. A larger copper wire can improve the noise reduction performance of PDS and reduce its Joule losses. A compromise solution obtained from a multi-objective optimization remains the excellent noise reduction and reduces Joule losses.

This paper explores the impact of PDS parameters on its operation and provides an orientation of PDS optimization, which is favorable to extend its application in different electrical machines.

The purpose objective of this study is to identify the friction coefficient and friction effect in electromagnetic upsetting (EMU) high-speed forming process.

Based on numerical simulation and upsetting experiment of 2A10 aluminum alloy bar, the friction coefficient between contact surfaces is obtained by combining the fitting displacement distribution function and the electromagnetic-mechanical coupling numerical model, and the influence of friction effect is analyzed.

The maximum impact velocity and acceleration during EMU are 13.9 m/s and −3.3 × 106 m/s², respectively, and the maximum strain rate is 7700 s⁻¹. The functional distribution relationship between friction coefficient combination (FS, FD) and characteristic parameters [upper diameter (D1) and middle diameter (D2)] is established. The values of FS and FD are 0.1402 and 0.0931, respectively, and the maximum relative error is 2.39%. By analyzing the distribution of equivalent stress and strain, it is found that plastic deformation has obvious zoning characteristics and there is serious failure concentration in the strong shear zone.

Friction coefficient significantly affects stress or strain distributions in material forming process, but it is difficult to obtain friction coefficients through experimental tests in the high-speed forming process. In this paper, a multi-field coupling numerical model is proposed to determine friction coefficients and applied to the electromagnetic impact loading process (a high-speed forming process).

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-05-2024-0154/

The purpose of this paper is to introduce a double-stator switched reluctance machine (DS-SRM) for electric vehicles (EVs) and to propose multi-mode operations for this machine.

Analysis of flux linkage distributions and torque characteristics using finite element method (FEM). Building a dynamic simulation model based on electromagnetic characteristics, mathematical equations and mechanical motion equations of the DS-SRM drive system. The paper proposes multi-mode operations (inner-stator excitation mode, outer-stator excitation mode and double-stator excitation mode) based on motor working regions. It also conducts simulation and experimental results to verify the effectiveness of the proposed multi-mode operations strategies and control schemes.

There is almost no electromagnetic coupling between the inner and outer stators due to the specially designed rotor structure and optimized windings polarity configuration. Analysis of flux linkage distributions and torque characteristics verified the independence of inner and outer stators. Proposal of multi-mode operations and corresponding control rules achieved the smooth switching between different modes.

The paper introduced the DS-SRM for EVs and proposed multi-mode operations, along with control rules, to optimize its performance. The specially designed rotor structure, optimized winding polarity configuration, and the proposed multi-mode operations contribute to the originality of the research.

Five-level rectifiers have received widespread attention because of their excellent performance in high-voltage and high-power applications. Taking a five-level rectifier with only four-IGBT for this study, a sliding mode predictive control (SMPC) algorithm is proposed to solve the problem of poor dynamic performance and poor anti-disturbance ability under the traditional model predictive control with the PI outer loop.

First, mathematical models under the two-phase stationary coordinate system and two-phase synchronous rotating coordinate system are established. Then, the design of the outer-loop sliding mode controller is completed by establishing the sliding mode surface and design approach rate. The design of the inner-loop model predictive controller was completed by discretizing the mathematical model equations. The modulation part uses a space vector modulation technique to generate the PWM wave.

The sliding mode predictive control strategy is compared with the control strategy with a PI outer loop and a model predictive inner loop. The proposed control strategy has a faster dynamic response and stronger anti-interference ability.

For the five-level rectifier, the advantages of fast dynamic influence and parameter insensitivity of sliding mode control are used in the voltage outer loop to replace the traditional PI control, and which is integrated with the model predictive control used in the current inner loop to form a novel control strategy with a faster dynamic response and stronger immunity to disturbances. This novel strategy is called sliding mode predictive control (SMC).

This paper aims to develop a model that reflects the current transformer (CT) core materials nonlinearity. The model enables simulation and analysis of the CT excitation current that includes the inductive magnetizing current and the resistive excitation current.

A nonlinear CT model is established with the magnetizing current as the solution variable. This model presents the form of a nonlinear differential equation and can be solved discretely using the Runge–Kutta method.

By simulating variations in the excitation current for different primary currents, loads and core materials, the results demonstrate that enhancing the permeability of the B–H curve leads to a more significant improvement in the CT ratio error at low primary currents.

The proposed model has three obvious advantages over the previous models with the secondary current as the solution variable: (1) The differential equation is simpler and easier to solve. Previous models contain the time differential terms of the secondary current and excitation flux or the integral term of the flux, making the iterative solution complicated. The proposed model only contains the time differential of the magnetizing current. (2) The accuracy of the excitation current obtained by the proposed model is higher. Previous models calculate the excitation current by subtracting the secondary current from the converted primary current. Because these two currents are much greater than the excitation current, the error of calculating the small excitation current by subtracting two large numbers is greatly enlarged. (3) The proposed model can calculate the distorted waveform of the excitation current and error for any form of time-domain primary current, while previous models can only obtain the effective value.