Search results

The purpose of this paper is to obtain the mechanical behavior and damage mechanism of the coal and rock near the stope under the stress state and stress paths of the surrounding rock with the dynamic mining.

Through the three-axial compression test and the uniaxial compression test by meso experiment device, the mechanical behavior and fracture evolution process of coal and rock were studied, and the acoustic emission (AE) characteristics under uniaxial compression of the coal and rock were contrasted.

Under the three-axial compression, the strength of coal and rock enhance significantly by confining pressure. The volume of outburst coal shows obvious stages: compression is followed by expansion. The coal first appear to undergo compaction under vertical stress due to volume decrease, but with the development of micro- and macro-cracks, the specimens appeared to expand; under the uniaxial compression, through the comparison of stress–strain relationship and the crack propagation process, stress drop and fracture of coal have obvious correlation. The destruction of coal was gradual due to the slow and steady accumulation of internal damage. Due to the influence of the end effect, the specimens show the “conjugate double shear failure”. The failure process of the coal and rock and the characteristics of the AEs have a corresponding relationship: the failure causes a large number of AE events. Before the events peak, there was an initial stage, calm growth stage and explosive growth stage. There were some differences between the rock and coal in the characteristics of the AE.

These research studies are conducted to provide guidance on the basis of mine disaster prevention and control.

The purpose of this study is to evaluate the methods employed for classifying and quantifying the potential of squeezing in tunnels. Along with the empirical and semi‐empirical approaches presently available in order to anticipate the potential of squeezing tunnel problems, the squeezing potential of Karaj water transfer tunnel and North West Tunnel Convey (NWTC) tunnels (Lot 2), located in Iran, are evaluated and presented. Those two case studies have an interesting geology profile and parameters to identify and then evaluate the squeezing potential.

In recent years, there has been an increasing interest in the tunnel construction. This paper describes the squeezing behavior of poor rock mass associated with deformability and strength properties. In Karaj water transfer tunnel, there are eight lithological rock types; and NWTC tunnel (Lot2) has 21 Lithological rock types. The parameters for rock classification, such as rock quality designation (RQD), rock mass rating (RMR), modified RMR, Q‐system, geological strength index (GSI), rock mass index (RMi), and rock structure rating (RSR) are evaluated and presented here. The parameters mentioned above are the input parameters for squeezing study in Karaj and NWTC tunnels. According to different methods of squeezing evaluation of tunnel presented in tables, the results of two case studies are presented in this paper.

One of the more significant findings to emerge from this study showed that about 3 km of the second part of NWTC tunnel, and 2 km of the Karaj tunnel have high squeezing potential. This research deals with not only an overview of the methods used for the identifying and quantifying of squeezing along with the empirical and semi‐empirical approaches presently available in order to anticipate the potential of squeezing tunnel problem, but also the case studies of NWTC and Karaj tunnels to evaluate and compare the potential of squeezing by different methods. These two tunnel case studies have high potential of squeezing therefore the lining of those two tunnels must be strong enough to overcome this issue.

This study is a precise and concise comparison of the evaluation of tunnels under squeezing rock condition. The present study confirms the previous findings and contributes additional evidence that suggests that there are many studies conducted using empirical and analytical methods to determine the squeezing phenomenon in tunnels. This paper responds to the various questions like, what is the squeezing phenomenon. How can we quantify the potential of squeezing in weak rock? What are the different approaches to the understanding of squeezing phenomenon?

Despite the many advantages this type of equipment offers, there are still some major drawbacks. Linear cutting machine (LCM) cannot accurately simulate the true rock-cutting process as 1. it does not account for the circular path along which tunnel boring machine (TBM) disk cutters cut the tunnel face, 2. it does not accurately model the position of a disk cutter on the cutterhead, 3. it cannot perfectly replicate the rotational speed of a TBM. To enhance the knowledge of these issues and in order to mimic the real rock-cutting process, a new lab testing equipment was developed by Hyundai Engineering and Construction.

A new testing machine called rotary cutting machine (RCM) is designed to simulate the excavation process of hard-rock TBMs and includes features such as TBM cutterhead, RPM simulation, constant normal force mode and constant penetration rate mode. Two sets of tests were conducted on Hwandeung granite using different disk cutter sizes to analyze the cutting forces in various excavation modes. The results are analyzed using statistical analysis and dimensional analysis. A new model is generated using dimensional analysis, and its results are compared against the results of actual cases.

The effectiveness of the new RCM test was demonstrated in its ability to apply various modes of excavation. Initial analysis of chip size revealed that the thickness of the chips is largely dependent on the cutter spacing. Tests with varying RPM showed that an increase in RPM results in an increase in the normal force and rolling force. The cutting coefficient (CC) demonstrated a linear correlation with penetration. The optimal specific energy is achieved at an S/p ratio of around 15. However, a slightly lower S/p ratio can also be used in the design if the cutter specifications permit. A dimensional analysis was utilized to develop a new RCM model based on the results from approximately 1200 tests. The model's applicability was demonstrated through a comparison of TBM penetration data from 26 tunnel projects globally. Results indicated that the predicted penetration rates by the RCM test model were in good agreement with actual rates for the majority of cases. However, further investigation is necessary for softer rock types, which will be conducted in the future using concrete blocks.

The originality of the research lies in the development of Hyundai Engineering and Construction’s advanced full-scale laboratory rotary cutting machine (RCM), which accurately replicates the excavation process of hard-rock tunnel boring machines (TBMs). The study provides valuable insights into cutting forces, chip size, specific energy, RPM and excavation modes, enhancing understanding and decision-making in hard-rock excavation processes. The research also presents a new RCM model validated against TBM penetration data, demonstrating its practical applicability and predictive accuracy.

The interaction between rock mass structural planes and dynamic stress levels is important to determine the stability of rock mass structures in underground geotechnical engineering. In this work, the authors aim to focus on the degradation effects of fracture geometric parameters and unloading stress paths on rock mechanical properties.

A three-dimensional Particle Flow Code (PFC3D) was used for a systematic numerical simulation of the strength failure and cracking behavior of granite specimens containing prefabricated cracks under conventional triaxial compression and triaxial unilateral unloading. The authors demonstrated the unique mechanical response of prefabricated fractured rock under two conditions. The crack initiation, propagation, and coalescence process of pre-fissured specimens were analyzed in detail.

The authors show that the prefabricated cracks and unilateral unloading conditions not only deteriorate the mechanical strength but also have significant differences in failure modes. The degrading effect of cracks on model strength increases linearly with the decrease of the dip angle. Under the condition of true triaxial unilateral unloading, the deterioration effect of peak strength of rock is very significant, and unloading plays a role in promoting the instability failure of rock after peak, making the rock earlier instability failure. Associating with the particle vector diagram and crack coalescence process, the authors find that model failure mode under unilateral loading conditions is obviously distinct from that in triaxial loading. The peak strain in the unloading direction increases sharply, resulting in a new shear slip.

This study is expected to improve the understanding of the strength failure and cracking behavior of fractured rock under unilateral unloading.

The induction of geological disasters is predominantly influenced by the dynamic evolution of the stress and plastic zones of the multilayer rock formations surrounding deep-rock roadways, and the behaviours and mechanisms of high in situ stress are key scientific issues related to deep-resource exploitation. The stress environment of deep resources is more complex owing to the influence of several geological factors, such as tectonic movements and landforms. Therefore, in practical engineering, the in situ stress field is in a complex anisotropic three-dimensional state, which may change the deformation and failure law of the surrounding rock. The purpose of this study is to investigate the tunnelling-induced stress and plastic evolution causing instability of multilayered surrounding rock by varying three-dimensional in situ stresses.

Based on data from the Yangquan Coal Mine, China, a finite difference model was established, and the elastic-plastic constitutive model and element deletion technology designed in the study were analysed. Gradual tunnelling along the roof and floor of the coal seam was used in the model, which predicted the impact tendency, and compared the results with the impact tendency report to verify the validity of the model. The evolutions of the stress field and plastic zone of the coal roadway in different stress fields were studied by modifying the maximum horizontal in situ stress, minimum horizontal in situ stress and lateral pressure coefficient.

The results shown that the in situ stress influenced the stress distribution and plastic zone of the surrounding rock. With an increase in the minimum horizontal in situ stress, the vertical in situ stress release area of the roof surrounding rock slowly decreased; the area of vertical in situ stress concentration area of the deep surrounding rock on roadway sides decreased, increased and decreased by turn; the area of roof now-shear failure area first increased and then decreased. With an increase in the lateral pressure coefficient, the area of the horizontal in situ stress release area of the surrounding rock increased; the area of vertical in situ stress release area of the roof and floor surrounding rock first decreased and then increased; the area of deep stress concentration area of roadway sides decreased; and the plastic area of the surrounding rock and the area of now-shear failure first decreased and then increased.

The results obtained in this study are based on actual cases and reveal the evolution law of the disturbing stress and plastic zone of multilayer surrounding rock caused by three-dimensional in situ stress during the excavation of deep rock roadways, which can provide a practical reference for the extraction of deep resources.

This study aims to research the large cross-section tunnel stability evaluation method corrected after considering the thickness-span ratio.

First, taking the Liuyuan Tunnel of Huanggang-Huangmei High-Speed Railway as an example and taking deflection of the third principal stress of the surrounding rock at a vault after tunnel excavation as the criterion, the critical buried depth of the large section tunnel was determined. Then, the strength reduction method was employed to calculate the tunnel safety factor under different rock classes and thickness-span ratios, and mathematical statistics was conducted to identify the relationships of the tunnel safety factor with the thickness-span ratio and the basic quality (BQ) index of the rock for different rock classes. Finally, the influences of thickness-span ratio, groundwater, initial stress of rock and structural attitude factors were considered to obtain the corrected BQ, based on which the stability of a large cross-section tunnel with a depth of more than 100 m during mechanized operation was analyzed. This evaluation method was then applied to Liuyuan Tunnel and Cimushan No. 2 Tunnel of Chongqing Urban Expressway for verification.

This study shows that under different rock classes, the tunnel safety factor is a strict power function of the thickness-span ratio, while a linear function of the BQ to some extent. It is more suitable to use the corrected BQ as a quantitative index to evaluate tunnel stability according to the actual conditions of the site.

The existing industry standards do not consider the influence of buried depth and span in the evaluation of tunnel stability. The stability evaluation method of large section tunnel considering the correction of overburden span ratio proposed in this paper achieves higher accuracy for the stability evaluation of surrounding rock in a full or large-section mechanized excavation of double line high-speed railway tunnels.

The purpose of the study is to quickly identify significant heterogeneity of surrounding rock of tunnel face that generally occurs during the construction of large-section rock tunnels of high-speed railways.

Relying on the support vector machine (SVM)-based classification model, the nominal classification of blastholes and nominal zoning and classification terms were used to demonstrate the heterogeneity identification method for the surrounding rock of tunnel face, and the identification calculation was carried out for the five test tunnels. Then, the suggestions for local optimization of the support structures of large-section rock tunnels were put forward.

The results show that compared with the two classification models based on neural networks, the SVM-based classification model has a higher classification accuracy when the sample size is small, and the average accuracy can reach 87.9%. After the samples are replaced, the SVM-based classification model can still reach the same accuracy, whose generalization ability is stronger.

By applying the identification method described in this paper, the significant heterogeneity characteristics of the surrounding rock in the process of two times of blasting were identified, and the identification results are basically consistent with the actual situation of the tunnel face at the end of blasting, and can provide a basis for local optimization of support parameters.

Reliability plays an important role in the execution of the maintenance improvement and the understanding of its concepts is essential to predict the type of maintenance according to the equipment state. Thereby, a computational tool was developed and programming with VBA in Excel® for reliability and failure analysis in a mining context. The paper aims to discuss these issues.

The developed approach use the modeling of stochastic processes, such as the renewal process, the non-homogeneous Poisson process and less conventional method as the Bayesian approach, by considering Jeffreys non-informative prior. The resolution gives the best associated model, the parameters estimation, the mean time between failure and the reliability estimate. This approach is validated with the reliability analysis of inter-failure times from underground rock bolters subsystems, over a two-year period.

Results show that Weibull and lognormal probability distribution fit to the most subsystems inter-failure times. The study revealed that the bolting head, the rock drill, the screen handler, the electric/electronic system, the hydraulic system, the drilling feeder and the structural consume the most repair frequency. The hydraulic and electric/electronic subsystems represent the lowest reliability after 50 operation hours.

For the first time, this case study defines practical failures and reliability information for rock bolter subsystems based on real operation data. This paper is useful to the comparative evaluation of rock bolter by detecting the weakest elements and understanding failure patterns in the individual observation subsystems on the overall machine performance.

The purpose of this study is to investigate the deformation characteristics and failure modes of the right bank slope of Xiluodu Hydropower Station after excavation.

Micro-seismic monitoring technology is applied to obtain the microfracture information and study the internal damage evolution law of the slope rock mass. A numerical model for discontinuous deformation analysis (DDA) is established to analyse the deformation characteristics and failure mode of the slope. Micro-seismic monitoring and DDA can verify and supplement each other's results in the investigation of slope failure.

The results show that the slope has a downhill displacement along the weathered zone under natural conditions; the maximum resultant displacement at the monitoring point is 380 mm. The micro-seismic events are concentrated in an area located 30–100 m horizontally away from the slope surface and at an elevation of 390–470 m. The distribution of these micro-seismic events is consistent with the location of the unloading and weathered zones; it is the same as the DDA simulation result.

The study is anticipated to be used as reference for the stability analysis of rock slopes. By combining the continuous (micro-seismic monitoring technology) and discontinuous (DDA) methods, the entire process starting from the gradual accumulation of internal rock micro-damage to the macroscopic discontinuous deformation and failure of the slope can be investigated.

An empirical examination of the perceived differences in offer quality between Western Australian rock lobster exporters and their respective Japanese importers reveals that consistent quality, a willingness to provide market information and a willingness to meet importers” immediate needs were the most important variables influencing an importer's decision to purchase. While both importers and exporters agreed that delivering consistent quality was the most important variable, exporters ranked competitive price much higher than importers. This suggests that Western Australian exporters may benefit from adding greater value to their product offer by providing continuous product support, timely market information and responding better to importers' immediate needs, rather than attempting to compete on price against lower cost producers.