Search results

This paper evaluates an alternative queuing concept for marine container terminals that utilize a truck appointment system (TAS). Instead of having all lanes providing service to trucks with appointments, this study considers the case where walk-in lanes are provided to serve those trucks with no appointments or trucks with appointments but arrived late due to traffic congestion.

To enable the analysis of the proposed alternative queuing strategy, the queuing system is shown mathematically to be stationary. Due to the complexity of the model, a discrete event simulation (DES) model is used to obtain the average waiting number of trucks per lane for both types of service lanes: TAS-lanes and walk-in lanes.

The numerical experiment results indicated that the considered queuing strategy is most beneficial when the utilization of the TAS lanes is expected to be much higher than that of the walk-in lanes.

The novelty of this study is that it examines the scenario where trucks with appointments switch to the walk-in lanes upon arrival if the TAS-lane server is occupied and the walk-in lane server is not occupied. This queuing strategy/policy could reduce the average waiting time of trucks at marine container terminals. Approximation equations are provided to assist practitioners calculate the average truck queue length and the average truck queuing time for this type of queuing system.

Due to the conflicts between left turn traffic and opposite straight-going traffic in urban traffic network, some of the traffic lanes cannot be used to discharge vehicles during its green phases and the intersection capacity can be greatly reduced. This study/paper aims to reduce the effect of conflicts and increase its capacity through the reasonable pre-signal phase time with the exchangeable lanes.

This paper took into consideration various influence factors to intersection capacity and formulated the capacity optimization model based on 0-1 mixed-integer programming model. This model is efficiently solved by standard branch-and-bound algorithms.

The authors took an intersection as an example and solved the optimal signal timing and entrance lane capacity via this model. Then, simulations were carried out to verify the effect of the exchangeable lanes strategy of this intersection through the simulation software VISSIM and take the traffic volume and delay as outputs, which indicated that this model has better performance.

The front-end control strategy can not only exploit the full potential of the intersection but also significantly improve the operational efficiency of the intersection. It plays a positive role in improving urban intersection congestion.

As of December 2022, there were 119,000 gas stations, 10,800 gas stations and 4,488,000 charging piles nationwide, while the number of vehicles reached 312 million, including 11.49 million new energy vehicles. The imbalance between transportation energy supply and energy replenishment demand leads to crowded queues of vehicles at some stations and idle resources in others. How to reduce the phenomenon of large queues and improve the utilization rate of idle resources is the key to alleviating the imbalance between supply and demand.

Therefore, from the perspective of spatio-temporal equilibrium of urban transportation energy supply stations, multi-energy supply station cooperation is established in view of the phenomenon of large spatio-temporal differences among different energy supply stations, and corresponding inducing strategies are adopted for energy supplement vehicles in the road network, so that part of queued users go to energy supply stations with fewer vehicles, so as to balance the supply and demand of transportation energy in the region. On this basis, the income distribution of urban transportation energy supply station is discussed.

The total revenue after the cooperation was 13,095, an increase of 22.9%. Secondly, in terms of distribution rationality, three impact factors are selected and Shapley correction value is used to distribute the total income. Compared with independent operation, both sites have a certain degree of increase.

Traffic congestion at energy supply stations is closely related to the number, location and number of vehicles at energy supply stations. Therefore, using a cooperative approach of energy trading cannot solve the queuing problem. In addition, there are a few research results on the equalization of energy supply station services considering time-of-use pricing. However, these studies do not consider the vehicular grooming at congested stations. As far as the authors know, there are no relevant research results in the research on the service equilibrium of energy supply stations based on cooperative games.

The purpose of this paper is to develop a framework to evaluate and assess the performance of the COVID-19 vaccine distribution process that is sensitive to the unique supply-side and demand-side constraints exhibited in the US vaccine rollout.

A queuing framework that operates under two distinct regimes is formulated to analyze service rates that represent system capacity to vaccinate (under the first regime) and hesitancy-induced throughput (under the second regime). These supply- and hesitancy-constrained regimes form the focus of the present paper, as the former reflects the inherent ability of the nation in its various jurisdictions to mobilize, whereas the latter reflects a critical area for public policy to protect the population’s overall health and safety.

The two-regime framework analysis provides insights into the capacity to vaccinate and hesitancy-constrained demand, which is found to vary across the country primarily by politics and region. The framework also allows analysis of the end-to-end supply chain, where it is found that the ability to vaccinate was likely constrained by last-mile administration issues, rather than the capacity of the manufacturing and transportation steps of the supply chain.

This study presents a new framework to consider end-to-end supply chains as dynamic systems that exhibit different regimes because of unique supply- and demand-side characteristics and estimate rollout capacity and underlying determinants at the national, state and county levels.

This research studies a location-allocation problem considering the m/m/m/k queue model in the blood supply chain network. This supply chain includes three levels of suppliers or donors, main blood centers (laboratories for separation, storage and distribution centers) and demand centers (hospitals and private clinics). Moreover, the proposed model is a multi-objective model including minimizing the total cost of the blood supply chain (the cost of unmet demand and inventory spoilage, the cost of transport between collection centers and the main centers of blood), minimizing the waiting time of donors in blood donating mobile centers, and minimizing the establishment of mobile centers in potential places.

Since the problem is multi-objective and NP-Hard, the heuristic algorithm NSGA-II is proposed for Pareto solutions and then the estimation of the parameters of the algorithm is described using the design of experiments. According to the review of the previous research, there are a few pieces of research in the blood supply chain in the field of design queue models and there were few works that tried to use these concepts for designing the blood supply chain networks. Also, in former research, the uncertainty in the number of donors, and also the importance of blood donors has not been considered.

A novel mathematical model guided by the theory of linear programming has been proposed that can help health-care administrators in optimizing the blood supply chain networks.

By building upon solid literature and theory, the current study proposes a novel model for improving the supply chain of blood.

This paper considers locating congested fast charging stations (FCSs) and deploying chargers in a stochastic environment, while the related studies have predominantly focused on problems in deterministic environments. Reducing the inconvenience caused by congestion at FCSs is an important challenge for FCS service provider. This is the underlying motivation for this study to consider a problem for FCS network design with the congestion restriction in a stochastic environment. We proposed a maximal coverage problem subject to budget constraints and a congestion restriction in order to maximize the demand coverage. With the derivation of the congestion restriction in the considered stochastic environment, the problem is formulated into an integer programming model. A real-life case study is conducted and managerial implications are drawn from its results.

The purpose of this paper is to describe how emerging open standards are replacing traditional industrial networks. Current industrial Ethernet networks are not interoperable; thus, limiting the potential capabilities for the Industrial Internet of Things (IIoT). There is no forthcoming new generation fieldbus standard to integrate into the IIoT and Industry 4.0 revolution. The open platform communications unified architecture (OPC UA) time-sensitive networking (TSN) is a potential vendor-independent successor technology for the factory network. The OPC UA is a data exchange standard for industrial communication, and TSN is an Institute of Electrical and Electronics Engineers standard for Ethernet that supports real-time behaviour. The merging of these open standard solutions can facilitate cross-vendor interoperability for Industry 4.0 and IIoT products.

A brief review of the history of the fieldbus standards is presented, which highlights the shortcomings for current industrial systems in meeting converged traffic solutions. An experimental system for the OPC UA TSN is described to demonstrate an approach to developing a three-layer factory network system with an emphasis on the field layer.

From the multitude of existing industrial network schemes, there is a convergence pathway in solutions based on TSN Ethernet and OPC UA. At the field level, basic timing measurements in this paper show that the OPC UA TSN can meet the basic critical timing requirements for a fieldbus network.

This paper uniquely focuses on the specific fieldbus standards elements of industrial networks evolution and traces the developments from the early history to the current developing integration in IIoT context.

This research aims to improve the performance of rail fastener defect inspection method for multi railways, to effectively ensure the safety of railway operation.

Firstly, a fastener region location method based on online learning strategy was proposed, which can locate fastener regions according to the prior knowledge of track image and template matching method. Online learning strategy is used to update the template library dynamically, so that the method not only can locate fastener regions in the track images of multi railways, but also can automatically collect and annotate fastener samples. Secondly, a fastener defect recognition method based on deep convolutional neural network was proposed. The structure of recognition network was designed according to the smaller size and the relatively single content of the fastener region. The data augmentation method based on the sample random sorting strategy is adopted to reduce the impact of the imbalance of sample size on recognition performance.

Test verification of the proposed method is conducted based on the rail fastener datasets of multi railways. Specifically, fastener location module has achieved an average detection rate of 99.36%, and fastener defect recognition module has achieved an average precision of 96.82%.

The proposed method can accurately locate fastener regions and identify fastener defect in the track images of different railways, which has high reliability and strong adaptability to multi railways.

This paper presents a generic simulation model to determine the equipment mix (quay, yard and intra-terminal transfer) for a Container Terminal Logistics Operations System (CTLOS). The simulation model for the CTLOS, a typical type of discrete event dynamic system (DEDS), consists of three sub-models: ship queue, loading-unloading operations and yard-gate operations. The simulation model is empirically applied to phase 1 of the Yangshan Deep Water Port in Shanghai. This study considers different scenarios in terms of container throughput levels, equipment utilization rates, and operational bottlenecks, and presents a sensitivity analysis to evaluate and choose reasonable equipment ratio ranges under different operational conditions.

Internet of Things’ (IoT’s) first wave started with tracking services for better inventory management mainly using radio frequency identification (RFID) technology. Later on, monitoring services became one of the major interests, including sensing technologies, and then more actuation for remote control-type of IoT applications such as smart homes, smart cities and Industry 4.0. In this paper, the authors focus on the RFID technology impairment. They propose to take advantage of the mature IoT technologies that offer native service discovery such as blutooth or LTE D2D ProSe or Wifi Direct. Using the automatic service discovery in the new framework will make heterogeneous readers aware of the presence of other readers and this will be used by the proposed distributed algorithm to better control the multiple RFID reader interference problem. The author clearly considers emerging Industry 4.0 use case, where RFID technology is of major interest for both identification and tracking. To enhance the RFID tag reading performance, collisions in the RFID frequency should be minimized with reader-to-reader coordination protocols. In this paper, the author proposes a simple distributed reader anti-collision protocol named DiSim that makes use of proximity services of IoT network and is compliant with the current RFID standards. The author evaluates the efficiency of the proposal via simulation.

In this paper, the author proposes a simple distributed reader anti-collision protocol named DiSim that makes use of proximity services of IoT network and is compliant with the current RFID standards. The author evaluates the efficiency of the proposal via simulation to study its behavior in very dense and heterogeneous RFID environments. Specifically, the author explores the coexistence of powerful static readers and small mobile readers, comparing the proposal with a standard ETSI CSMA method. The proposal reduces significantly the number of access attempts, which are resource-expensive for the readers. The results show that the objectives of DiSim are met, producing low reader collision probability and, however, having lower average readings per reader per time.

DiSim is evaluated with the ETSI standard LBT protocol for multi-reader environments in several environments with varied levels of reader and tag densities, having both static powerful RFID readers and heterogeneous randomly moving mobile RFID readers. It effectively reduces the number of backoffs or contentions for the RFID channel. This has high reading success rate due to the avoided collisions; however, the readers are put to wait, and DiSim has less average readings per reader per time. As an additional side evaluation, the ETSI standard LBT mechanism was found to present a good performance for low-density mid-coverage scenarios, however, with high variability on the evaluation results.

To show more results, the author needs to do real experimentation in a warehouse, such as Amazon warehouse, where he expects to have more and more robots, start shelves, automatic item finding on the shelve, etc.

Future work considers experimentation in a real warehouse equipped with heterogeneous RFID readers and real-time analysis of RFID reading efficiency also combined with indoor localization and navigation for warehouse mobile robots.

More automatization is expected in the future; this work makes the use of RFID technology more efficient and opens more possibilities for services deployment in different domains such as the industry which was considered not only in this paper but also in smart cites and smart homes.

Compared to the literature, the proposal offers the advantage to not be dependent on a centralized server controlling the RFID readers. It also offers the possibility for an existing RFID architecture to add new readers from a different manufacturer, as the readers using the approach will have the possibility to discover the capabilities of the new interaction other RFID readers. This solution takes advantage of the available proximity service that will be more and more offered by the IoT technologies.